Résumé du contenu de la page N° 1
OWNER’S MANUAL
DATA PROJECTOR
TDP-T95
TDP-T100
Others Maintenance Operations Preparations Before Using
Résumé du contenu de la page N° 2
Before Using SAFETY PRECAUTIONS The lightning flash with arrowhead symbol, within an equilateral triangle, is intended - Reorient or relocate the receiving antenna. to alert the user to the presence of uninsulated "dangerous voltage" within the product's - Increase the separation between the equipment and receiver. enclosure that may be of sufficient magnitude to constitute a risk of electric shock to - Connect the equipment into an outlet on a circuit different from that to which the receiver i
Résumé du contenu de la page N° 3
IMPORTANT SAFETY INSTRUCTIONS CAUTION:PLEASE READ AND OBSERVE ALL WARNINGS AND 5. Heat 8. Power-Cord Protection INSTRUCTIONS GIVEN IN THIS OWNER'S MANUAL AND THOSE The product should be situated Power-supply cords should be MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR FUTURE away from heat sources such as routed so that they are not likely to REFERENCE. radiators, heat registers, stoves, or be walked on or pinched by items other products (including placed upon or against them, This unit is fully
Résumé du contenu de la page N° 4
IMPORTANT SAFETY INSTRUCTIONS (Continued) e) If the product has been dropped or 10. Lightning storms 12. Do not place the product 15. Accessories damaged in any way (If the cabinet For added protection for this vertically Do not place this product on an should break, please handle with product during storm, or when it is unstable cart, stand, tripod, Do not use the product in the care to avoid injury) . left unattended and unused for bracket, or table. The product may upright position to proje
Résumé du contenu de la page N° 5
IMPORTANT SAFETY INSTRUCTIONS (Continued) POWER SUPPLY CORD SELECTION If your line voltage is 220 to 240V, use one of the following types of cable. 19. Replacement Parts 22. Do not use the product in When replacement parts are a closed installation state. Plug Plug required, be sure the service Do not place the product in a box configuration Plug type Line voltage configuration Plug type Line voltage technician has used replacement or in any other closed installation Australian 200 – 240V parts
Résumé du contenu de la page N° 6
IMPORTANT PRECAUTIONS (Continued) Avoid Volatile Liquid Disposal Do not use volatile liquids, such as an insect spray, near the unit. Do not leave rubber or This product contains substances which are harmful to humans and the environment. plastic products touching the unit for a long time. They will leave marks on the finish. • The lamp contains mercury. If cleaning with a chemically saturated cloth, be sure to follow the product's precautions. Please dispose of this product or used lamps in
Résumé du contenu de la page N° 7
CONTENTS Before Using Maintenance SAFETY PRECAUTIONS .................................................................................. 2 About lamp ......................................................................................................... 43 IMPORTANT SAFETY INSTRUCTIONS ........................................................... 4 Lamp replacement ............................................................................................. 44 POWER SUPPLY CORD SELECTION ........
Résumé du contenu de la page N° 8
Preparations Checking the package contents Names of each part on the main unit Please make sure that the following items are included in the box, along with the main unit. (6)(5) (4) (3) (2) (1) If any item is missing, please contact the store immediately where you purchased the product. (1) (5) (8) (6) (2) (7) (3) (3) (7)(8) (9) (10) (11) (12) (13) (12)(14) (15) (4) Back Front (See note) ■■ (1) Remote control ■■ (6) Power cord Name : Function ■■ (2) LR03 (SIZE AAA) batteries for remote ■■
Résumé du contenu de la page N° 9
Names of each part on the control panel and remote control Name : Main Function Control panel Remote Control (13)AUTO SET button : Sets up analog input from computer. p.28 Remote control Warning label (9) (10) (11) Laser light (14) Laser indicator : Lights when laser is on. transmitter source p.20 (15) Mouse control button : Controls a mouse pointer. ® p.20 (14) (16)PAGE+ button : Proceeds PowerPoint slides. (4) (13) p.30 (17) MUTE button : Cuts off the picture and sound temporarily. (1) (3)
Résumé du contenu de la page N° 10
Approx. 5m Names of the terminals on the rear panel Preparing and using the remote control (1) (2) (3) (4) (5) (6) ■ Loading dry-cell batteries ■ Operating the remote into the remote control control q Remove the battery cover. Turn on the ON/OFF switch of the remote control. Point toward the projector’s infrared remote sensor, and press a button on the remote control. • Operating the projector from the front w Insert the dry-cell batteries. Be sure to align the plus and minus Approx. 15° ends of
Résumé du contenu de la page N° 11
Operating a computer using the remote control Placement A computer can be operated using the projector’s remote control. This function is available Placement Styles ® ® ® on any computer with the Windows 98/98SE, Windows Me, Windows 2000, or Win- As shown in the figures below, this device can be placed in 4 different styles. ® dows XP OS, that is equipped with a USB port which can support USB1.1 (The mouse The factory setting is “floor-mounted front projection.” Set the [Projection mode] in the
Résumé du contenu de la page N° 12
Connection Notes Before connection • The COMPUTER 1 IN terminal functions identically to the COMPUTER 2 IN terminal. • Read the owner’s manual of the device you are connecting to the projector. • Some types of computer cannot be used or connected to this projector. • The MONITOR OUT terminal outputs signals from the COMPUTER 1 IN terminal or the p.50 COMPUTER 2 IN terminal, or outputs Y/PB/PR as selected with the INPUT button. If no Check for an RGB output terminal, supported signal , etc. •Turn
Résumé du contenu de la page N° 13
Operations Turning the power on and off Notes ■ Connecting the power cord • The start-up screen will disappear after a moment. You can dismiss the start-up screen Insert the power cord connector into 1 before this by performing any operation. You can also configure the start-up screen not to the AC IN socket of the projector. p.37 appear via the Display setting menu . • The first time you use the projector after purchase, after the start-up screen disappears, Insert the power cord plug into a 2
Résumé du contenu de la page N° 14
Basic operations Turn on the power. 5 Projector placement angle adjustments 1 p.24 Turn on the power by following the instructions in “Turning the power on” . The placement angle and the height of the projected image can be adjusted by the foot adjuster. 2 Select the language and the lamp power (When using the q Lift up the front of the projector to first time). 1 the desired angle, then press the foot adjuster release button. When the projector is used for the first time after purchase, the sta
Résumé du contenu de la page N° 15
Using handy features Adjusting Keystone distortion [Auto] ■ Using auto setting (Only for input from computer) Remote 2 This function sets up the projector to the optimum state such as Press the button. Control sampling phase, frequency, screen position, and clamp for each The keystone distortion is automatically corrected. The icon appears during this type of the input signal by using simple operations. correction. When adjustment is finished, the Keystone menu appears again. For fine adjust-
Résumé du contenu de la page N° 16
Using handy features (Continued) Notes ■ Changing screen size • The icon appears while resizing. Remote The screen size for the projected image can be changed. • Operating a function other than Mute will release resizing. Control Press the remote control’s SCREEN SIZE button. • As zooming is processed digitally, the image quality is degraded in larger zoom Pressing the button switches Full/Thru/Wide in turn. ratio. • During resizing or moving the zooming area, the image may be distorted. Notes
Résumé du contenu de la page N° 17
Using handy features (Continued) How to cancel password (from [On] to [Off]) ■ Password function 1 When the password function is added and [Password] is set to [On], image projection Select [Password] in the Default setting menu and press the or requires an entry of the preset password at power-on. button. To add the password function, perform the following procedure: The password entry screen is displayed. (The password function, once added, cannot be deleted. Set [Password] to [Off] if you 2
Résumé du contenu de la page N° 18
Using the menus You can call up on-screen menus, and conduct a number of adjustments and settings using ■ The image adjustment menu p.16 the operation buttons on the control panel (main unit side) and remote control. Use this menu to set or adjust image-related items. Items that can be set or adjusted are marked with “Yes”, and those that cannot are marked with “No”. (When an item is masked, ■ How to use the menus it indicates that you cannot select for the current input.) The menu shown below
Résumé du contenu de la page N° 19
Using the menus (Continued) ■ The display setting menu Item Description Computer Y/PB/PR Video S-video Use this menu to set screen display-related items. Position V-position Yes No No No (The items in gray color cannot be set with the current input selection.) Adjust the vertical position of the image. Clamp 1 Yes No No No Description Item Adjusts the clamp pulse position. Screen size Clamp 2 Yes No No No (Full): Display with 1024 × 768 dot resolution Adjusts the clamp pulse width. (Thru):
Résumé du contenu de la page N° 20
Using the menus (Continued) Note Notes • If you use the screen size setting function on commercial video software, •You can register a logo from computer input only. broadcast or cable-broadcasting programs to display images with the varying • The area that can be registered is 512 × 384 dots at the center of the screen. To aspect ratio except for the purpose of your private viewing and listening, it may register a company logo, prepare the image within the limit. infringe the copyright protecte
