Résumé du contenu de la page N° 10
L - C L I C K D R Connection Turning the power on and off Before connection Connecting the power cord • Read the owner’s manual of the device to be connected to the projector. Insert the power cord connector into the 1 • Some types of computer cannot be used connected to this projector. AC IN socket of the projector. p.36 Check for an RGB output terminal, supported signal , etc. • Turn off the power of both devices before connection. Insert the power cord plug into a wall or 2 • The figure bel
Résumé du contenu de la page N° 11
L - C L I C K D R Turning the power on and off (Continued) Basic operations Notes 1 Turn on the power. • The start-up screen will disappear after a moment. You can dismiss the start-up screen p.19 Turn on the power, following the instructions in “Turning on the power” . before this by performing any operation. You can also configure the start-up screen not to p.29 appear via the Display setting menu . 2 Select language (When using for first time). • The first time you use the projector after pu
Résumé du contenu de la page N° 12
L - C L I C K D R Basic operations (Continued) Using handy features 5 Projector placement angle adjustments Using auto setting (Auto setting) The placement angle and the height of the projected image can be adjusted by the foot This function sets up the projector to the optimum state for Remote adjuster. Control panel Control each type of the input signal by using simple operations. q Lift up the front of the projector until 1 ON LAMP TEMP FAN 1 Press the AUTO SET button. ON/STANDBY LASER CALL
Résumé du contenu de la page N° 13
L L L L - - - - C C C C L L L L I I I I C C C C K K K K D D D D R R R R Using handy features (Continued) Correcting the keystone distortion (Keystone) Freezing the image (Freeze) Remote p.22 When the foot adjuster is used to change the The image being projected can be made to be frozen. This function is to Control Remote projection angle, the picture will undergo keystone (trap- be used to pause a video during a presentation, etc. Control panel Control ON/STANDBY LASER CALL ezoidal) distort
Résumé du contenu de la page N° 14
L - C L I C K D R Using handy features (Continued) Using the menus You can call up on-screen menus, and conduct a number of adjustments and settings, Displaying Information [Status display] p.14 using the operation buttons on the control panel (main unit side) and remote control. This displays information about the input signal, lamp use time, etc. Press the button twice (or press the CALL button on the remote How to use the menus control once). The menu shown below is only for operation i
Résumé du contenu de la page N° 15
Using the menu (Continued) The image adjustment menu The display setting menu Use this menu to adjust image-related items. Use this menu to set screen display-related items. Items Items that can be adjusted are marked with “Yes”, and those that cannot are marked Description Item with “No”. Screen size Item Description Computer Y/PB/PR Video S-video (Full): Display with native resolution (1,024 x 768 pixels) Contrast Lower Higher Yes Yes Yes Yes (Thru): Display with sampling resolutio
Résumé du contenu de la page N° 16
L - C L I C K D R Operating a computer using the remote control Lens and main unit cleaning A computer can be operated using the projector’s remote control. This function is available Lens cleaning on any computer with the Windows 98SE, Windows Me, Windows 2000, Windows XP, Mac • Clean the lens with a commercially available blower and/or OS 9, or Mac OS X, that is equipped with a USB port which can support USB1.1. lens cleaner. However, please note that Toshiba does not the guarantee operatio
Résumé du contenu de la page N° 17
Lamp replacement (Continued) Trouble indications The indicator lights inform you of internal abnormalities. Remove the lamp cover. 3 1 Loosen the screws and remove the lamp cover. 3 ON LAMP TEMP FAN No power 2 ⇒ Problem with projector • Unplug the power cord, and contact your dealer. 4 Pull out the lamp. ⇒ The lamp cover is not properly attached. Loosen the three screws holding the lamp in place, p.32 • Unplug the power cord, and reattach the lamp cover. and pull on the handle to remove the lam
Résumé du contenu de la page N° 18
Before calling service personnel Specifications If you think something is wrong, check the following before contacting customer service. List of general specifications p.33 Please see “Trouble indications” as well. Item Specification If This Happens Check Consumption Power 340 W Weight 2.4 kg No power • Is the power cord plugged in? Is it connected to the projector? p.33 External Dimensions 248 × 90 × 201 mm (W × H × D) • Is the lamp cover loose? (including protruding parts) p.33 Power goes
Résumé du contenu de la page N° 19
Specifications (Continued) List of supported signals (RGB signals) List of supported signals (Y/PB/PR signals) This projector supports the following RGB signals. Note, however, that depending on the Signal format fh(kHz) fv(Hz) computer model, the screen may show flicker or streaking. Please adjust the projector if 480i(525i)@60Hz 15.73 59.94 this happens. 480p(525p)@60Hz 31.47 59.94 p.23 (Press the AUTO SET button, and adjust automatically or manually. ) 576i(625i)@50Hz 15.63 50.00 576p(6
Résumé du contenu de la page N° 20
Specifications (Continued) CONTROL terminal Pin assignment Pin No. Signal Name Description 1 RXD Receiving data 12 2 CTS Consent to send 4 3 DSR Data set ready 4 GND Signal ground 3 5 5 RTS Request to send 6 N.C No connection 6 8 7 TXD Sending data 7 8 N.C No connection Mini DIN 8 pin connector Interface format 1 Communication method RS-232C, 9600bps, No Parity, Data Length: 8 bits; Stop Bit Length: 1 bit 2 Communication format STX (02h) Command (3Byte) ETX (03h) Only 1 command valid per
Résumé du contenu de la page N° 1
ON LAMP TEMP FAN
ON/STANDBY INPUT
MENU
VO - V +
L. OL.
AUTO KEYSTONE AUTO SET
OWNER’S MANUAL
DLP DATA PROJECTOR
TDP-D1
TDP-D2
Others Maintenance Operations Preparations Before Using
Résumé du contenu de la page N° 2
SAFETY PRECAUTIONS IMPORTANT SAFETY INSTRUCTIONS THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. : WARNING OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: ( ) ( ) CAUTION:PLEASE READ AND OBSERVE ALL WARNINGS AND 1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE,AND 2 THIS DEVICE MUST ACCEPT BEFORE OPERATING,PLEASE READ OWNER'S MANUAL. INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. DO NOT REMOVE SCREWS EXCEPT LAMP COVER SCREWS. THIS CLASS B DIGITAL APPRATUS COMPLIES WITH CANAD
Résumé du contenu de la page N° 3
IMPORTANT SAFETY INSTRUCTIONS (Continued) 5. Heat 8. Power-Cord Protection 11. Object and Liquid Entry 14. Attachments The product should be situated Power-supply cords should be Never push objects of any kind Do not use attachments not away from heat sources such as routed so that they are not likely to into this product through openings recommended by the product radiators, heat registers, stoves, or be walked on or pinched by items as they may touch dangerous manufacturer as they may cause o
Résumé du contenu de la page N° 4
IMPORTANT SAFETY INSTRUCTIONS (Continued) 16. Damage Requiring Service 18. Servicing 21. Do not leave thermal-paper Unplug this product from the wall Do not attempt to service this documents or easily outlet and refer servicing to product yourself as opening or deformed items on top of qualified service personnel under removing covers may expose you the unit or near the air the following conditions: to dangerous voltage or other exhaust. a) When the power-supply cord or hazards. Refer all serv
Résumé du contenu de la page N° 5
POWER SUPPLY CORD SELECTION IMPORTANT PRECAUTIONS (Continued) If your line voltage is 220 to 240V, use one of the following types of cable. Avoid Volatile Liquid Do not use volatile liquids, such as an insect spray, near the unit. Do not leave rubber or Plug Plug configuration Plug type Line voltage configuration Plug type Line voltage plastic products touching the unit for a long time. They will leave marks on the finish. If cleaning with a chemically saturated cloth, be sure to follow the p
Résumé du contenu de la page N° 6
CONTENTS EXEMPTION CLAUSES •Toshiba Corporation bears no responsibility in the case of damages arising from natural Before Using disaster such as earthquakes, lightning, etc., fire not liable to Toshiba Corporation, operating SAFETY PRECAUTIONS .......................................................................................... 2 IMPORTANT SAFETY INSTRUCTIONS ................................................................... 3 by third parties, other accidents, or use under abnormal condi
Résumé du contenu de la page N° 7
Checking the package contents Names of each part on the main unit Please make sure that the following items are included in the box, along with the main unit. (6) (5) (4) (3) (2) (1) If an item is missing, please contact the store from which you purchased the product immediately. (1) (6) (11) (2) (7) (12) (10) (3) (8) (7) (8) (9) WARNING Label CAUTION Label (4) (9) MODEL NO./ (7) (9) (8) (15) (16) RATING Label (5) (10) WARNING Label SERIAL No. Label CAUTION Label (1) Remote control
Résumé du contenu de la page N° 8
L - C L I C K D R Names of each part on the control panel and remote control Control Panel Remote Control (18) Pointer control button : Moves mouce pointer (Computer operation) p.30 p.30 (19) L-CLICK button : L-click of mouse (Computer operation) Laser emitter (10) (9) (8) (7) Laser (15) (24) (20) R-CLICK button : R-click of mouse (Computer operation) p.30 Remote control Warning ON LAMP TEMP FAN transmitter p.30 (21) DRAG button : DRAG of mouse (Computer operation) ON/STANDBY LASER (22) INPUT
Résumé du contenu de la page N° 9
Approx. 5m Approx. 5m Preparing and using the remote control Placement Loading dry-cell batteries Operating the remote control Placement Styles As shown in the figures below, this device can be placed in 4 different styles. into the remote control Point the remote control toward the The factory setting is “floor-mounted front projection.” Set the placement style in the projector’s infrared remote sensor, q Remove the battery cover. p.28 default setting menu , in accordance with your needs. a
