Résumé du contenu de la page N° 1
PjNET-30
OWNER'S MANUAL
The owner's manuals of Pj-to NetDirector are included on the supplied docu-
ment CD-ROM as the PDF file format. To read the owner's manual, set the docu-
ment CD-ROM onto your computer and follow the guide on the screen.
To read the owner's manual, you need the Adobe Reader (Adobe Acrobat
Reader) version 6.0 or later software in your computer. The Adobe Reader can be
obtained from the Adobe website (http://www.adobe.com).
Pj-to NetDirector
Quick Setup Guide
ACT
LINK
EN
Résumé du contenu de la page N° 2
Read this First Compliance Federal Communication Commission Notice This equipment has been tested and found to comply EIKI PjNET-30 with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to Tested To Comply With FCC Standards provide reasonable protection against harmful interfer- ence in a residential installation. This equipment gener- FOR HOME OR OFFICE USE ates, uses and can radiate radio frequency energy and, if not installed and use
Résumé du contenu de la page N° 3
Read this First CaUTIoN oN USE IN NET woRK - W hen you receive an alert e-mail from the projector, you must check the projector immediately. Fire or accident may result if the projector is used in an abnormal condition. - When you install the projector at remote location and use it through the network, you must perform the safety inspections periodically. In this case you must pay attention to the change of environment in which you installed the projector. It may cause fire or an accident
Résumé du contenu de la page N° 4
Quick Setup Guide Read this First Package contains The package contains following items. Check each item as you unpack the package. If you have any of the following items missing, contact the sales dealer. ❑ Network unit 1 piece ❑ Quick Setup Guide 1 piece English/Japanese ❑ Software CD-ROM 1 piece Network Viewer & Capture 3 software PJ Network Manager software ❑ Document CD-ROM 1 piece Pj-to NetDirector Owner's Manual PJ Network Manager Owner's manual How to read the o wner's Manual on CD
Résumé du contenu de la page N° 5
Computer environment Read this First o perating environment To perform the managing and setting of the projector by using this product, the environ- ment described below is required. Standard mode Windows 98, Windows Me, Windows NT4.0SP6 Operating System Windows 2000, Windows XP Higher than Pentium III 900MHz Recommended CPU 64MB (Minimum)/ 128MB or more(Recommended) Memory 128MB or more for WindowsXP HDD free area 100MB or more Drive equipment CD-ROM drive S upport one of following resolutions
Résumé du contenu de la page N° 6
Setting up Name and function of each part (Top View) PowER indicator This lights up red when the network function is set ON in the projector menu. Mounting screws Mount by using a coin etc. a CT indicator This turns on and off with green when sending or receiving of data LINK indicator This lights up red when the network unit is connected to the network correctly. (Bottom View) Connector plug Connecting to the terminal on the pro- jector. Serial port Used to control the external equipmen
Résumé du contenu de la page N° 7
Setting up Installation and network configuration Connector Cover Mounting Screw Cover 1 D isconnect the AC plug from the projector. 2 R emove the connector cover and screw covers (2 pieces) from the projector and insert plug on this product to the option connector. 3 T ighten two screws by using a coin etc. Screw Cover Connection of LaN cable To connect to the network, it is required to use the UTP (Unshielded Twisted Pair) straight cable with RJ-45 plug. There are two different types of ca
Résumé du contenu de la page N° 8
Setting up Network configuration Confirmation of the network menu When installing this product to the projector, the network on-screen menu items for this product are activated automatically. If not activated, the product may not have been installed correctly. Please check item "Mounting" ( ☞ p.7). Configure the network Before performing the network configuration, prepare network address numbers (IP Address, Subnet Mask, Default Gateway, DNS) assigned to the projector. Ask your network admi
Résumé du contenu de la page N° 9
Setting up 1 2 2 Configuration for IP Address/ Sub net/ Gateway* /DNS* Press SELECT button again. The following network setting pallet appears on the screen. Enter the specified network addresses. The red frame moves sequentially left or right with 7 8 button. The number up or down with d e button. (Example of the screen display) * W ithout the above method of using point buttons, there are some methods to set the network address, using the screen 10-key pallet or using the direct 10-key en
Résumé du contenu de la page N° 10
Setting up Login the setting page of the projector 1 Enter the IP address Launch the web browser installed in your computer, enter the IP address into the "Address" on the browser and then press "Enter" key. Enter the address (192.168.1.201) that you configured in item "Network configura- tion" ( ☞ p.9). The default IP address is [192.168.0.2]. 2 Select a display mode and login T his product provides 2 types of control mode, Standard Mode and Light Mode as the below. Select a proper mode t
Résumé du contenu de la page N° 11
Setting up 3 Display of main setting page The following main setting page will be displayed according to your display mode selection. Perform various kinds of settings through this page. Click on the menus to dis- play the control and setting pages. z Main setting page in the Standard Mode display Clock display Display on or off by clicking text ON or OFF Sub menu tab Switches the sub menu tab Page numbers Switches the pages by clicking the number's tab Setting page Returns to Display Mai
Résumé du contenu de la page N° 12
Software Installation Guide Installing the software To install the software into the computer with w indows 2000, w indows XP or w indows NT, you should logon as administrator. Before installation, make sure that the other applications are closed, otherwise installation cannot be made properly. Network Viewer & Capture 3 installation 1 Set the supplied Network Viewer & Capture 3 CD-ROM into the CD-ROM drive of your computer. Double click SetupTool.exe icon in the "Tool" folder in the CD-RO
Résumé du contenu de la page N° 13
Software Installation Guide Installed software and places Network Viewer 3 (File Converter 2) is installed in the "Printers and Faxes" folder in the "Control Panel". ● Network Viewer 3 (File Converter 2): This is a kind of the printer driver to convert to the JPEG data optimized to project by the pro- jector from any of the documents created by the application software. PJ Network Manager installation 1 S et the supplied CD-ROM into the CD-ROM dr i ve o f your comp uter. D oub le click Setu
Résumé du contenu de la page N° 14
U.S.A. Canada EIKI International, Inc. EIKI CANADA - Eiki International, Inc. 30251 Esperanza P.O. Box 156, 310 First St. - Unit 2, Rancho Santa Margarita Midland, ON, L4R 4K8, Canada CA 92688-2132 Tel : 800-563-3454 (705)-527-4084 U.S.A. Fax : 800-567-4069 (705)-527-4087 Tel : 800-242-3454 (949)-457-0200 E-Mail : canada@eiki.com Fax : 800-457-3454 (949)-457-7878 E-Mail : usa@eiki.com Eastern Europe Deutschland & Österreich EIKI CZECH spol. s.r.o. EIKI Deutschland GmbH Umelecká 15 Am Frauwald 1
