Résumé du contenu de la page N° 1
SERVICE MANUAL
X1160 Series/X1260 Series
X1160Z Series/X1260K Refresh
Date Revise Version Description
2007.08.27 V1.0 Initial Issue
2008.07.09 V2.0 Add X1160 Refresh/X1260 Refresh
2008.08.25 V3.0 Add X1160Z/X1160Z Refresh
2008.10.10 V4.0 Add X1260K Refresh
Copyright October.2008. All Rights Reserved P/N: 36.88T03G001
SI : TSE: Check: Approved:
Résumé du contenu de la page N° 2
PARTS X1160 X1160refresh X1160Zrefresh X1160Z X1260 X1260refresh X1260Krefresh LOGO 35.88T02G001 35.88T03G001 35.89B02G001 MYLAR IO MYLAR 35.88T01G001 35.89B01G001 THERMAL N/A 43.89T17G001 SWITCH DMD 48.87K01G001 48.87M01G001 48.89B01G001 SPEAKER N/A 49.89B01G001 BLOW- 49.88T01G001 ER1 BLOW- N/A 49.86E02G001 ER2 ZOOM N/A 51.89B04G001 51.89B04G001 RING FRONT IR N/A 51.88T24G001 N/A 51.88T24G001 CAP FRONT 51.88T03G001 51.88T27G001 75.89B02G001 75.89B01G001 75.89B02G001 COVER IR SEN- N/A 80.87Y05G0
Résumé du contenu de la page N° 3
Preface This manual is applied to X1160 Series/X1260 Series/X1160Z Series/X1260K Refresh projection system. The manual gives you a brief description of basic technical information to help in service and maintain the product. Your customers will appreciate the quick response time when you immediately identify problems that occur with our products. We expect your customers will appreciate the service that you offer them. This manual is for technicians and people who have an electronic backgr
Résumé du contenu de la page N° 4
Table of Content Chapter 1 Introduction Highlight 1-1 Compatible Mode 1-3 Product Overview 1-5 Chapter 2 Disassembly Process Equipment Needed & Product Overview 2-1 Disassemble Lamp Cover Module 2-2 Disassemble Lamp Module 2-2 Disassemble Top Cover Module 2-3 Disassemble T
Résumé du contenu de la page N° 5
Assemble LVPS Module 2-20 Assemble Lamp Driver Module 2-21 Assemble Interrupt Switch Module 2-22 Assemble Fan Module 2-23 Assemble
Résumé du contenu de la page N° 6
Optical Performance Measure 4-11 Other 4-12 Chapter 5 Firmware Upgrade Equipment Needed 5-1 DLP Composer Lite Setup Procedure 5-2 USB Driver Upgrade Procedure 5-4 Firmware Upgrade Procedure 5-5 Waveform Download 5-8 Chapter 6 EDID Upgrade EDID Introduction 6-1 Equipment Needed 6-2 Setup Procedure 6-3 EDID Key-In Procedure 6-4 Default Language Reset
Résumé du contenu de la page N° 7
Chapter 1 Introduction 1-1 Highlight No Item Description 1 Dimensions (LxWxH) - 267 mm x 187 mm x 80 mm 2 Weight - <5 lbs - 7 degree with elevator mechanism (for X1160/X1260/ X1160Z) 3 Tilt Angle - 3 degree with elevator mechanism (for X1160 refresh /X1260 refresh/X1160Z refresh/X1260K refresh) - Universal AC 100 – 240 V ~ 50-60 Hz with PFC input - 160W for Osram E20.6 Lamp @ normal operation (for x1160 series/x1260 series/x1160z series) 4 Power Supply - 180W for Osram E20.
Résumé du contenu de la page N° 8
No Item Description Engineering Spec: - 1500 : 1 Full White and Black (Minimum; Full power mode) (for X1160/X1260/X1160Z) - 1800 : 1 Full White and Black (Typical; Full power mode) (for X1160/X1260/X1160Z) - 1400 : 1 Full White and Black (Minimum; Full power mode) (for X1160 refresh/X1260 refresh/X1160Z refresh) 8 Contrast - 1800 : 1 Full White and Black (Typical; Full power mode) (for X1160 refresh/X1260 refresh/X1160Z refresh) - 400 : 1 Full White and Black (Minimum; Full pow
Résumé du contenu de la page N° 9
No Item Description - Number of active dots : 800(H) x 600(V) (for X1160/ X1160 refresh/1160Z/X1160Z refresh) 16 Number of active dots - Number of active dots : 1024(H) x 768(V) (for X1260/X1260 refresh/X1260K refresh) - Hsync Frequency 31 ~ 69 kHz (for X1160 refresh/X1160/ X1160Z/X1160Z refresh) - Hsync Frequency 31 ~ 80 kHz (for X1260 refresh/X1260K refresh) - Vsync Frequency 50 ~ 85 Hz - Video Signal RGB (PC) ● Analog RGB 0.7Vp-p, 75 ohm, Separate TTL H,V Sync 17 Input signal spec
Résumé du contenu de la page N° 10
1-2 Compatible Mode VGA Analog - PC Signal Compatibility Resolution V-Sync [Hz] H-Sync [KHz] 640x480 60 31.50 640x480 72 37.90 640x480 75 37.50 VGA 640x480 85 43.30 720x400 70 31.50 720x400 85 37.90 800x600 56 35.10 800x600 60 37.90 800x600 72 48.10 SVGA 800x600 75 46.90 800x600 85 53.70 832x624 75 49.70 1024x768 60 48.40 1024x768 70 56.50 XGA 1024x768 75 60.00 1024x768 85 68.70 1152x864 70 63.80 1152x864 75 67.50 1280x1024 60 64.00 1152x864 (For X1260/X1260 re- 85 77.10 fresh/X1260K refresh
Résumé du contenu de la page N° 11
VGA Analog - Extended Wide timing Compatibility Resolution V-Sync [Hz] H-Sync [KHz] 1280x768 60 48.36 1280x768 75 60.30 1280x720 60 44.80 1280x768 WXGA (For X1260/X1260 re- 85 68.60 fresh/X1260K refresh) 1280x800 60 49.60 1440x900 60 59.90 X1160 Series/X1260 Series/X1160Z Series/X1260K Refresh Confidential 1-5
Résumé du contenu de la page N° 12
Product Overview Projector Outlook Front /Upper side Item Description Item Description Zoom ring (X1260 series/ Power button and Power Indicator 1 5 X1260K Refresh) LED 2 Focus ring 6 Remote controller 3 Zoom lens 7 Remote control receiver 4 Lens cap X1160 Series/X1260 Series/X1160Z Series/X1260K Refresh Confidential 1-6
Résumé du contenu de la page N° 13
Rear side Item Description Item Description PC analog signal/HDTV/component 1 6 KensingtonTM lock port video input connector RS232 connector (Only for X1260 refresh/ 2 S-Video input connector 7 X1260/X1260K refresh) Monitor loop-through output 3 Composite video input connector 8 connector (VGA-Out) (Only for X1260 refresh/ X1260/X1260K refresh) Audio input connector (Only for X1260 re- 4 USB connector 9 fresh/X1260/X1260K refresh) 5 Power socket X1160 Series/X1260 Series/X1160Z Series/X1260K Ref
Résumé du contenu de la page N° 14
Remote Control and Control Panel Layout Item Icon Function Description 1 Infrared transmitter Sends signals to the projector. 2 Power/Power LED Power button and Power Indicator LED. 3 POWER Refer to the “Turning the Projector On/Off” section. • Press “MENU” to launch the Onscreen display (OSD) menu, back to the previous step for the OSD menu 4 MENU operation or exit the OSD menu. • Confirm your selection of items. Four directional select Use up, down, left, right buttons to select items or make
Résumé du contenu de la page N° 15
Item Icon Function Description Automatically synchronizes the projector to the input 10 RESYNC source. Press “SOURCE” to choose RGB, Component, S-Video, 11 SOURCE Composite and HDTV sources. Momentarily turns off the video. Press “HIDE” to hide the 12 HIDE image, press again to display the image. Empowering 13 Unique Acer functions: eView, eTimer Management. key 14 FREEZE To pause the screen image. X1160 Series/X1260 Series/X1160Z Series/X1260K Refresh Confidential 1-9
Résumé du contenu de la page N° 16
Connecting the Projector Item Description Item Description 1 Power cord 5 S-Video cable 2 VGA cable 6 Audio cable jack/jack 3 Composite video cable 7 RS232 cable 4 USB cable Note: To ensure the projector works well with your computer,please make sure the timing of the display mode is compatible with the projector. X1160 Series/X1260 Series/X1160Z Series/X1260K Refresh Confidential 1-10
Résumé du contenu de la page N° 17
X1160 Refresh/X1160/X1160Z Refresh/X1160Z XTAL 20MHz Main Board CDCDLP223 100MHz 20MHz 320MHz 512Mbits XDR Front IR Flash DRAM CDCD5704 DMD Board For Option 8 bits 400MHz DC 3.3V ADC VGA Graphics VGA IN Port AD9883A Component Display 24bits Port 1 0.55" 2xLVDS Image DAD2000 SVGA DMD Chip XTAL 16 pair LVDS DDP2230 Svideo 14.318MHz Svideo Port Input Video decoder 10bits ASIC TVP5147 Port 3 CVBS Composite Port Input USB USB Port Input I2C DC output TMP75 EEPROM 8051-MCU 1.2V/2.5V W79E804ASG 3.3V/
Résumé du contenu de la page N° 18
X1260 Refresh/X1260/X1260K Refresh X1160 Series/X1260 Series/X1160Z Series/X1260K Refresh Confidential 1-12
Résumé du contenu de la page N° 19
Bottom Cover Dimension X1160 Series/X1260 Series/X1160Z Series/X1260K Refresh Confidential 1-13
Résumé du contenu de la page N° 20
Chapter 2 Disassembly& Assembly Process 2-1 Equipment Needed & Product Overview 1. Screw Bit (+) :107 2. Hex Sleeves 5mm 3. Screw Bit (+) :102 4. Screw Bit (-) :102 5. Long Nose Nipper 6. Tweezers X1160/X1160 refresh/X1260/X1260 refresh/X1160Z/X1160Z refresh/X1260K refresh 7. unit * Before you start: This process is protective level II. Operators should wear electrostatic chains. * Note: 1.If you need to replace the main board, you have to get into service mode and record the
