Instruction d'utilisation Sanyo 1AA6P1P1756

Résumé du contenu de la page N° 1

Rear Projection Display
Installation Manual
REQUEST A SALES DEALER FOR INSTALLATION
Please read all instructions below and install this system properly.
Please read "SAFETY PRECAUTIONS" and "IMPORTANT SAFETY INSTRUCTIONS" on
OWNER'S MANUAL to install and place this system.
This system is supplied in 3 packages and they need to be installed. Please make sure all the
parts are included. If any part is missing, or if you have questions, contact a sales dealer.
Install the system following steps.

Résumé du contenu de la page N° 2

CHECK CONTENTS IN PACKAGES 1 This system is supplied in 3 packages. Make sure all the parts listed below (cabinets, Installation parts, and accessories) are included in those packages. Package 1 Top Cabinet : Refer to the steps 3 to 6 for installation. Package 2 Bottom Cabinet : Refer to the steps 2, 6 and 7 for installation. Qty. Glass Doors ------------------------------------------- 2 Installation Parts Compartment Shelves ----------------------------- 4 Shelves' Pins -----------------------

Résumé du contenu de la page N° 3

ASSEMBLE BOTTOM CABINET 2 Cover Plates Joint Bolts (4 pcs) Remove Joint Bolts and Cover Plates 1 (2 pcs) Remove the 4 Joint Bolts on the Bottom Cabinet. Keep these bolts for later use. They are necessary for joint the Top and Bottom Cabinets. Joint Bolts (4 pcs) Remove the 2 Cover Plates on the top of the Bottom Cabinet. Keep the Cover Plates for later use. Replace those plates, when the appliance needs to be transported. 2 Install Center Panel Install the Center Panel to the Bottom Cabinet.

Résumé du contenu de la page N° 4

J0INT TOP AND BOTTOM CABINETS 3 Joint Top and Bottom Cabinets 1 Screws (14 pcs) Lift the Top Cabinet and put it on the Bottom Cabinet. When setting the Top Cabinet, be sure the frame of the Bottom Cabinet is fitted into the frame of the Top Cabinet completely. Top Cabinet CAUTION THE TOP CABINET OF THIS PROJECTOR HAS ITS GRAVITY AT THE SCREEN SIDE. WHEN LIFTING THE TOP CABINET, BE CAREFUL NOT TO DROP. Bottom Cabinet Remove Back Cover 2 Remove the 14 Screws and the Back Cover. Keep the screws

Résumé du contenu de la page N° 5

SETUP PROJECTION MIRROR 4 Preparation 1 Projection Mirror Remove the 4 Protection Pads inside of the Top Cabinet and remove the 2 Fixing Bands (right and left) of the Projection Mirror. Fixing Bands CAUTION NEVER TOUCH THE PROJECTION MIRROR DIRECTLY. IT MAY EFFECT THE PROJECTION IMAGE QUALITY. MOVE THE MIRROR BY HOLDING THE MIRROR HANDLE. Protection Pads (4pcs) BE SURE TO REMOVE ALL THE Projection Mirror PROTECTION PADS FROM THE CABINET. Fixing Bands (2 pcs) 2 Set Mirror Arms Remove the 8

Résumé du contenu de la page N° 6

ADJUST PROJECTION MIRROR 5 When the figure of the projection image does not match the Projection Screen, adjust the Projection Mirror. If the figure fits the Projection Screen precisely, skip the steps 2, 3 and 4 and replace the Back Cover. Check Projection Image 1 Connect the projector to the AC outlet, and turn the projector on. Connect the video output equipment to the projector. Project the image of cross-hatch or circles to check whether the picutre is displayed Screw(B) fully on the Pro

Résumé du contenu de la page N° 7

ASSEMBLE STORAGE SPACES 6 Screws (14 pcs) Replace Back Cover 1 Replace the Back Cover to the Top Cabinet. Turn the Back Cover over, and fix the cover in the reverse to the initial position. Back Cover Install Glass Doors 2 Holder Cover 1. Remove the Hinge Covers by removing the 2 screws of each Hinge. 2. Hold the Glass Doors between the Glass Hinges and the Hinge Covers. Install the Glass Doors so Screws (2pcs x 4) Holder Magnet that the side with the Holder Magnet is matched to the magnet ins

Résumé du contenu de la page N° 8

LOCK CABINET 7 Lock the Cabinet 1 Turn Lock Bolts to the direction indicated on the figure to lock the cabinet on the floor. Make sure that all the Casters are slightly raised from the floor. The tilt of Cabinet can be also adjusted with these Lock Bolts. Lock Bolt Lifting the Letting the cabinet up to cabinet down to CAUTION settle it. move it. BE SURE TO LOCK THE CABINET WITH LOCK BOLTS PROPERLY. IF THE CABINET IS NOT LOCKED, CABINET IS UNSTABLE AND MAY FALL DOWN. Cabinet Dimensions ( W x H