Résumé du contenu de la page N° 1
magicolor® 3100 Series
Service Manual
1750051-001B
The essentials of imaging
www.minolta-qms.com
Résumé du contenu de la page N° 2
ii
Résumé du contenu de la page N° 3
Introduction
Résumé du contenu de la page N° 4
Résumé du contenu de la page N° 5
Introduction 1. Trademarks The following are trademarks or registered trademarks of their respective owners. Other product names mentioned in this manual may also be trademarks or registered trademarks of their respective owners. Registered trademarks are registered in the United States Patent and Trademark Office; some trademarks may also be registered in other countries. QMS, magicolor, and the MINOLTA-QMS logo are registered trademarks of MINOLTA-QMS, Inc. Minolta is a trade-mark of Minol
Résumé du contenu de la page N° 6
Cautions for operation 1. Marks giving caution Maintenance operations requiring special cautions or additional information to descriptions of this manual are presented as "Warning", "Caution", or "Note", according to their nature. If instructions are not observed, death or serious injury may be caused. If instructions are not observed, injuries of workers or physical damages to assets (including this laser printer) may result. Particularly important essentials for procedures, steps, rules, and
Résumé du contenu de la page N° 7
Introduction While the printer is ON, never touch live parts if not required absolutely. Power is supplied to the power switch / inlet (LVPS ASSY) even while the printer is off. Never touch its live components. Do not touch live parts unless otherwise specified. vii
Résumé du contenu de la page N° 8
3.2 Driving units When servicing gears or other driving units, be sure to turn them OFF and plug off. Drive them manually when required. Never touch the gears or other driving units while the printer is running. 3.3 High-temperature units When servicing high-temperature units (securing unit, etc.), be sure to turn them OFF to prevent burns, injuries and other troubles, remove the power plug and start service processes after they have cooled down enough. Immediately after completion of operat
Résumé du contenu de la page N° 9
Introduction 3.5 Warning/caution labels Warning labels and caution labels are attached to this laser printer to prevent accidents Check those labels for their peeling or stain when servicing the printer. 3.5.1 Caution label for high-temperature units ix
Résumé du contenu de la page N° 10
4. List of Abbreviations ADC Automatic Density Control MPT Multipurpose Tray AG Analog Ground MSI Multi Sheet Inserter AUX Auxiliary N/F Normal Force B/W Blank and White NP No Paper BCR Bias Charge Roller NVM Non Volatile Memory BTR Bias Transfer Roller (Image Transfer Roller) OPC Organic Photo Conductor BUR Back Up Roller P/H Paper Handling C Cyan PCDC Pixel Count Dispense Control CART Cartridge PHD Printer Head (Imaging Cartridge) CCW Counterclockwise Pixel Picture Cell (Picture Element) CL Cl
Résumé du contenu de la page N° 11
Introduction Unpacking the Printer The printer must be carried horizontally with two or more persons. Extreme care must be taken to avoid personal injuries Check visually the printer for evidence of any damages. Peel all tapes off the printer. Remove protection parts (2 pieces) from the paper tray. xi
Résumé du contenu de la page N° 12
xii
Résumé du contenu de la page N° 13
Contents
Résumé du contenu de la page N° 14
Résumé du contenu de la page N° 15
CONTENTS Introduction ..................................................................................................... iii 1. Trademarks ...................................................................................................................... v 2. Copyright Notice............................................................................................................... v 1. Marks giving caution.................................................................................
Résumé du contenu de la page N° 16
1.3 Test Print Pattern .............................................................................................................................. 2-98 2. Diagnostics Using the MINOLTA- QMS magicolor 3100 Diagnostics (Hanabi Service Commander).........................................................................................2-99 2.1 General ............................................................................................................................................. 2-99
Résumé du contenu de la page N° 17
Table of Contents RRP3.8 SWITCH ASSY SIZE (PL3.2.4)...............................................................................................3-158 RRP3.9 LEVER LOW PAPER (PL3.2.7) .............................................................................................. 3-160 RRP3.10 INDICATOR (PL3.2.8)........................................................................................................... 3-162 RRP3.11 GUIDE INDICATOR (PL3.2.10) ......................................
Résumé du contenu de la page N° 18
RRP7.2 ROLL EXIT (PL7.1.4) ............................................................................................................. 3-214 RRP7.3 ROLL MID (PL7.1.5)................................................................................................................ 3-215 RRP7.4 MOTOR ASSY DUP (PL7.1.8) ................................................................................................ 3-216 RRP8. BTR ASSY & FUSER........................................................
Résumé du contenu de la page N° 19
Table of Contents Chapter 4 Plug/Jack (P/J) Connector Locations...................................... 4-271 1. Connector [P (plug) / J (jack)]....................................................................................4-273 1.1 List of P/J ........................................................................................................................................ 4-273 1.2 P/J layout diagram ......................................................................................
Résumé du contenu de la page N° 20
6.2 Operation Modes ............................................................................................................................ 6-360 7. Control.......................................................................................................................6-361 7.1 Control of Paper Size...................................................................................................................... 6-361 7.2 Selective Control on Paper Pick-up Unit.....................
