Résumé du contenu de la page N° 1
Drywall Screwdriver
MODEL 6800DBV
MODEL 680lDBV
INSTRUCTION MANUAL
DOUBLE
INSULATION
Bit shank No load speed Overall Net
MODEL Capacities
size (RPM) length weight
114” Hex 0 - 2,500 (;::E)
6800DBV
Drywall screws No. 6
Self drilling screw . . . 5 mm (3116”)
--I 6801DBV ,,4,, Hex 4,000 280 mm 1.5 kg
(1 1”) (3.3 Ibs)
’::,my
Résumé du contenu de la page N° 2
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools to rain. Don't use tool in presence of
Résumé du contenu de la page N° 3
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry tool with finger on switch. Be sure switch is OFF when plugging in. 16. EXTENSION CORDS. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltag
Résumé du contenu de la page N° 4
VOLTAGE WARNING: Before connecting the tool to a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY to the user - as well as damage to DO NOT PLUG IN THE TOOL. Using a power source with the tool. If in doubt, voltage less than the nameplate rating is harmful to the motor. SAVE THESE INSTRUCTIONS. ADDITIONAL SAFETY
Résumé du contenu de la page N° 5
Removing or installing locator assembly To remove the locator assembly, pull the Locking position locking sleeve forward and then turn it Locking sleeve-, counterclockwise. To install the locator assembly, screw it clockwise and then push the locking sleeve back in lightly toward the motor. Turn the locking sleeve slightly to match the locking positions and then push in firmly to lock the locator in place. I Locator \ I1 Removing or installing bit CAUTION : Always be sure that the
Résumé du contenu de la page N° 6
Initially, adjust the locator assembly to create a distance of approximately 1 mm (3/64") from the tip of the locator to the base of the screw head. One full turn of the locator equals 1.5 mm (1/16") change in depth. After adjusting the locator assembly, push the locking sleeve in to lock the locator in place. Drive a trial screw into your material or a piece of duplicate material. If the depth is not suitable for the screw, continue adjusting until the proper depth setting is obtained. 1
Résumé du contenu de la page N° 7
Reversing switch action This tool has a reversing switch to change the direction of rotation. Move the revers- ing switch lever to the & position for clockwise rotation or the .& position for counterclockwise. Reversing switch lever 1 CAUTION : Always check the direction of rotation before drilling. .Use the reversing switch only when the tool comes to a complete stop. Changing the direction of rotation before the tool stops may ruin the tool. Operation Fit the screw on the point of
Résumé du contenu de la page N° 8
ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. *Phillips insert bit (10 per pkg.) Magnetic bit holder Part No. 784801 -1 Size 1 Part No. 78421 2-OA Nose piece assembly 7842 1 1 -2A Part No. 12221 1-8 7842 1 1-6 78421 3-A I Reduce
Résumé du contenu de la page N° 9
Jun -07-'93 US 9
Résumé du contenu de la page N° 10
Jun -07- 93 US MODEL 6800DEV. 6801DBV IF"," ,",", DESCRIPTION MACHINE 11 Felt Cover 25 1 Rubber Pin 4 26 1 1 Ball Bearing 21 Felt Ring 30 62718 For Model 6800DBV 31 LOCatOl Locking Sleeve 608LB For Model 6801DBV 41 an sn 52 Pan Head Screw M4x55 (With Warherl ARMATURE ASSEMBLY 0 Ring 27 61 IWith Item 26 231 71 Gear Housing 1 23 Ball Bearing 62718 ni Leaf sprrng 30 1 Baffle piate 31 Sfeel Ball 3 5 1 FIELD ASSEMBLY 10 1 Spindle 31 32 2 Brush Holder 11 1 COmpreSSlO" sprrng
Résumé du contenu de la page N° 11
.. -. . . . . . __ I-- MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory, It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers. If inspection shows will repair (or at our option,
