Résumé du contenu de la page N° 1
®
APC Smart-UPS RT SURTA48XLBP/SURTA48XLBPJ
External Battery Pack User Manual
Introduction/Before Installation
About this Manual
®
The APC Smart-UPS RT external battery pack (SURTA48XLBP or SURTA48XLBPJ) connects to
the APC Smart-UPS RT uninterruptible power supply (SURTA1500XL and SURTA2000XL, or
SURTA1500XLJ). Together these units provide extended protection against blackouts, brownouts,
sags and surges reaching your computers, servers, and other sensitive electronic equipment.
Illustration
Résumé du contenu de la page N° 2
Pre-installation Procedure 4. Place the battery pack where it will be used. Ensure that air vents on the front and rear of the unit are not blocked. Do not operate the battery pack where there is excessive dust or the temperature or humidity are outside the specified limits. 40°C 95% 104°F 0% 2.5 2.5 cm cm Pre-installation Procedure 1. Once the battery pack is at the installation site, remove the top cover and battery modules to lighten the load and prepare the battery pack to be in
Résumé du contenu de la page N° 3
Tower Installation Tower Installation When installing the UPS and battery pack(s) as a tower configuration, they must be joined together with stabilizing feet and clips. Failure to comply to this instruction may result in bodily injury or equipment damage. Caution When installing the UPS and battery pack(s) as a tower configuration, battery pack(s) must be installed to the right of the UPS when facing the front of the UPS. Failure to follow this instruction could result in cabling shortage.
Résumé du contenu de la page N° 4
Tower Installation 2. Complete this step if adding battery pack(s) to an existing tower system. a. Turn Off the UPS and disconnect all equipment. Refer to the UPS user manual for instructions. b. Remove bezels, battery covers, and battery modules from all previously installed equipment. For additional instructions, refer to the UPS user manual and Transporting the Battery Pack to Another Location on page 10. c. Remove the feet from the last battery pack . d. Attach and mount the feet to t
Résumé du contenu de la page N° 5
Rack-mount Installation c. Install and connect the battery pack battery modules. d. Install the battery pack covers and bezel . 5. Go to Terminal Mode Configuration on page 9 to configure the UPS to recognize the battery pack(s). Rack-mount Installation 1. Complete this step if this is a new installation of the UPS with battery pack(s). a. Place the UPS on its side to remove the battery. To remove the battery, refer to the Battery Replacement Instructions procedure in the UPS u
Résumé du contenu de la page N° 6
Rack-mount Installation 3. Install the battery pack(s) and the UPS in the rack. The UPS must be installed ABOVE the battery pack(s) when in a rack. Failure to follow this instruction could result in cabling shortage. Note a. Refer to the installation sheet contained in the SURTRK rail box for instructions on how to install the cleats, rack-mount brackets, and labels on the UPS and battery pack(s). b. Refer to the installation sheet contained in the SURTRK rail box for instructions on how to
Résumé du contenu de la page N° 7
Battery Pack and UPS Connection Procedure b. Install the UPS and battery pack battery covers and bezels . 6. Go to Terminal Mode Configuration on page 9 to configure the UPS to recognize the battery pack(s). Battery Pack and UPS Connection Procedure The battery pack is equipped with the following connectors. Refer to the UPS user manual for UPS connector types and definitions. Connectors Type Description TVSS screw The UPS and battery pack features a Transient Voltage Surge-suppres- s
Résumé du contenu de la page N° 8
TVSS GND TVSS GND TVSS GND TVSS GND TVSS GND TVSS GND Battery Pack and UPS Connection Procedure 1. Connect the green/yellow ground wire(s) to the TVSS screw locations between the UPS and battery pack, or between battery packs as shown. 2. To connect the battery pack to the UPS and to connect battery packs to one another: a. Remove the UPS battery connector plate . b. Insert the adjacent battery pack connector cable plug into the connector receptacle on the UPS. c. If applica
Résumé du contenu de la page N° 9
Terminal Mode Configuration Terminal Mode Configuration This configuration affects the accuracy of the runtime calculations that the UPS performs while run- ning on battery power. ® Settings are made through supplied PowerChute Business Edition or Terminal Mode. Terminal mode can only be used with the serial cable provided with the UPS. If using a USB cable, disconnect the USB cable from the UPS, and connect the serial cable to the UPS before using the terminal program. Note Shown below is an
Résumé du contenu de la page N° 10
TVSS GND TVSS GND TVSS GND Storage, Transport, and Service Refer to the Troubleshooting section in the UPS user manual to solve minor battery pack or UPS installation and operation problems. Refer to www.apc.com with complex battery pack or UPS problems. Storage, Transport, and Service Storage Store the battery pack covered in a cool, dry location with the battery modules fully charged. At 5° to 113° F (15° to 45° C), charge the battery modules every six months. To Install a Replacement Bat
Résumé du contenu de la page N° 11
Storage, Transport, and Service 3. To lighten the load, remove the battery modules before transporting the battery pack to another location. a. Remove the bezel and battery covers . b. Disconnect and remove the battery modules. Service Always DISCONNECT THE BATTERY MODULES before shipping the battery pack to be in compliance with U.S. Department of Transportation (DOT) regulations. Caution If the battery pack requires service do not return it to the dealer. Follow these steps:
Résumé du contenu de la page N° 12
Limited Warranty American Power Conversion (APC) warrants its products to be free from defects in materials and workmanship for a period of two years from the date of purchase. Its obligation under this warranty is limited to repairing or replacing, at its own sole option, any such defective products. To obtain service under warranty you must obtain a Returned Material Authorization (RMA) number from customer support. Products must be returned with transportation charges prepaid and must be
