Résumé du contenu de la page N° 1
200208099 93-2040 SM1000RMX Owner’s Manual.qxd 9/12/2002 3:53 PM Page 1
Owner’s Manual
®
SmartPro RMX
1000-2000 VA
120V Input/Output UPS Systems
Intelligent • Line-Interactive Industrial Cabinet
U
L
CUS
1778
Important Safety Instructions 2
Mounting 3
Connection 5
Basic Operation 7
Storage and Service 10
Specifications 10
1111 W. 35th Street Chicago, IL 60609 USA
Customer Support: (773) 869-1234 • www.tripplite.com
®
Copyright © 2002 Tripp Lite. All rights reserved. SmartPro is a register
Résumé du contenu de la page N° 2
200208099 93-2040 SM1000RMX Owner’s Manual.qxd 9/12/2002 3:53 PM Page 2 Important Safety Instructions SAVE THESE INSTRUCTIONS This manual contains instructions and warnings that should be followed during the installation, operation and storage of all Tripp Lite UPS Systems. Failure to heed these warnings will void your warranty. UPS Location Warnings • Use caution when lifting UPS. Because of the considerable weight of all 3U Rackmount UPS systems, at least two people should assist in liftin
Résumé du contenu de la page N° 3
200208099 93-2040 SM1000RMX Owner’s Manual.qxd 9/12/2002 3:53 PM Page 3 Mounting Your UPS may be rackmounted in 4- or 2-post racks using these suggested mounting procedures. These procedures are for common rack types and may not be appropriate for all rack configurations. User must determine the fitness of rackmount hardware and procedures before mounting. Suggested Rackmount Installation for the SM1000RMX Attach mounting ears (A) to the front mounting 1 B holes of the UPS (B) using the screw
Résumé du contenu de la page N° 4
200208099 93-2040 SM1000RMX Owner’s Manual.qxd 9/12/2002 3:53 PM Page 4 Mounting continued Attach mounting ears (D) to the front mounting 3 E holes of your UPS (E) using the screws provided (F). Do not attach the mounting ears to your equipment’s middle holes. D F 3 Using an assistant if necessary, lift your 4 equipment and slide it onto the mounting shelves. Attach your equipment to the rack by passing the user-supplied screws, nuts and washers (G) through its mounting ears and G into the ra
Résumé du contenu de la page N° 5
200208099 93-2040 SM1000RMX Owner’s Manual.qxd 9/12/2002 3:53 PM Page 5 Connection Plug your UPS’s line cord into an 1 electrical outlet. Your UPS must be connected directly to a 3- wire grounded AC receptacle. Do not use extension cords with your UPS. Once your UPS is plugged in, the UPS will enter STANDBY mode. The fan will activate 1 and the “ ” LED will begin flashing. The SM2000RMX plug (NEMA L5-20P) shown UPS system’s outlets will not be active until the UPS is turned ON. Plug your equi
Résumé du contenu de la page N° 6
200208099 93-2040 SM1000RMX Owner’s Manual.qxd 9/12/2002 3:53 PM Page 6 Connection optional Your UPS will function properly without these connections. DB9 Port Connection 1 Using the DB9 cable provided, connect a DB9 port on your computer to a DB9 port on your UPS. Install the Tripp Lite power protection software appropriate to its operating system. If your UPS has two DB9 ports, a second computer with a DB9 port may be connected if desired. 1 SM1000RMX shown USB Port Connection 2 Using the
Résumé du contenu de la page N° 7
200208099 93-2040 SM1000RMX Owner’s Manual.qxd 9/12/2002 3:53 PM Page 7 Basic Operation Buttons (Front Panel) Use the POWER button to switch your UPS between its four modes of operation. OFF: No indicator lights are on. The UPS is completely shut down for storage or shipping. If the UPS is connected to AC power, it will start up in STANDBY mode. If the UPS is not connected to AC power and the POWER button is pressed for two seconds, the UPS will “cold start” into INVERT mode. STANDBY: The “ ”
Résumé du contenu de la page N° 8
200208099 93-2040 SM1000RMX Owner’s Manual.qxd 9/12/2002 3:53 PM Page 8 Basic Operation continued Indicator Lights (Front Panel) POWER: Lights green when the UPS is receiving AC power. Illuminates constantly when the UPS is in the ON mode, indicating that batteries are charging and connected equipment is receiving filtered AC power. Flashes while in STANDBY mode to indicate that batteries are charging but connected equipment is not receiving power. VOLTAGE CORRECTION: Lights green whenever yo
Résumé du contenu de la page N° 9
200208099 93-2040 SM1000RMX Owner’s Manual.qxd 9/12/2002 3:53 PM Page 9 Basic Operation continued Other UPS Features (Rear Panel) Ground Screw (Select Models Only): Use this to connect any equip- ment that requires a chassis ground. Smart DB9 Ports: Your UPS has one or two DB9 ports that may be used to connect the UPS to a DB9 port on any workstation or server. Use with Tripp Lite cabling and PowerAlert Software to monitor and man- age network power and automatically save open files and shut
Résumé du contenu de la page N° 10
200208099 93-2040 SM1000RMX Owner’s Manual.qxd 9/12/2002 3:53 PM Page 10 Storage & Service Storage Before storing your UPS, disconnect all equipment to avoid battery drain, then place the UPS in the OFF mode by putting it in STANDBY mode, then unplugging it (see Basic Operation, page 7). If you store your UPS for an extended period of time, recharge the UPS batteries once every three months by following Steps 1 and 2 in the Connection section (page 5) and allowing the UPS to charge its batter
Résumé du contenu de la page N° 11
200208099 93-2040 SM1000RMX Owner’s Manual.qxd 9/12/2002 3:53 PM Page 11 11
Résumé du contenu de la page N° 12
200208099 93-2040 SM1000RMX Owner’s Manual.qxd 9/12/2002 3:53 PM Page 12 93-2040 (200208099)
