Instruction d'utilisation Tripp Lite SmartPro 2200XLT

Résumé du contenu de la page N° 1

Owner's Manual
®
SmartPro
1111 W. 35th Street
2200XLT
Chicago, IL 60609 USA
Customer Support: (773) 869-1234
www.tripplite.com
Line-Interactive
UPS Systems (230V)
Safety: p. 2
Installation: p. 3 - 4
Basic Operation: p. 4 - 6
Storage & Service: p. 7
Specifications: p. 7
Warranty & Insurance: p. 6
®
Copyright © 1999 Tripp Lite. All rights reserved. SmartPro is a registered trademark of Tripp Lite.
1
9911081 230V Smartpro 2200T OM.p65 1 11/24/99, 12:00 PM

Résumé du contenu de la page N° 2

Safety This manual contains important instructions and warnings that should be followed during the installation, operation and storage of all Tripp Lite UPS Systems. UPS Location Warnings  Install your UPS indoors, away from excess moisture or heat, dust or direct sunlight.  For best performance, keep the indoor temperature between 32° F and 104° F (between 0° C and 40° C).  Leave adequate space around all sides of the UPS for proper ventilation. UPS Connection Warnings  Connect your UPS to

Résumé du contenu de la page N° 3

Installation Plug your UPS into 1 an electrical outlet. The SmartPro 2200XLT should be connected to a 15-amp dedicated circuit. Plug your equipment 2 into your UPS. Your UPS is designed to support only computer equipment. Connecting household appliances, laser printers or surge suppressors is not recommended. Turn your UPS ON. Figure 1 DIP Switch #4 3 Set the System Enable Switch (DIP (System Enable Switch) · Switch #4, UPS back panel) to the ENABLE “ENABLE” (UP) position. (See Figure 1) This sw

Résumé du contenu de la page N° 4

DB9 Port Connection –Optional–* Using Tripp Lite cable, connect your 1 primary server’s DB9 port to the single DB9 port labeled SMART/LAN 4.1 (which provides complete intelligent RS-232 communications) using the included cable labelled 73-743.** If you have additional 2 computers: a. Connect them to the DB9 ports labeled BASIC/LAN 2.2 (which provide basic, contact-closure shutdown capabilities) using the included cables labelled 73-844. b. Set their corresponding LAN Interface DIP Switches to th

Résumé du contenu de la page N° 5

ON/Standby Switch This momentary switch controls power to the UPS receptacles. Engage it momentarily and release it to toggle between the “ON” mode (power ON at the UPS receptacles) and “Standby” mode (power OFF at the UPS receptacles). Mute/Test Switch Use this momentary switch to do two things: Silence the blackout alarm Engage this switch and release it. Note: when the battery is nearly depleted, the alarm resumes (and cannot be silenced) to alert you to immediately shut down connected equip

Résumé du contenu de la page N° 6

This multi-colored light displays 4 separate UPS load conditions. It will turn from green (low) to yellow (medium) to red (high) as you connect equipment to show you the load level your UPS is support- ing. When the light is red your UPS is supporting a load above 85% of its capacity. If the red light begins flashing, your UPS is severely overloaded. Remove overload immediately until light stops flashing. Other UPS Features L6-20 AC Receptacle This locking receptacle provides your connected equi

Résumé du contenu de la page N° 7

Storage & Service Storage Turn your UPS OFF: first engage the ON/Standby Switch and release it to place your UPS in the “Standby” mode; then set the System Enable Switch (Jumper #4, UPS rear panel) to "DISABLE" (down); finally, disconnect the UPS power cord from the wall outlet. If you plan on storing your UPS for an extended period of time, recharge the UPS batteries once every three months. Follow steps #1 and #3 in the Quick Installation section and allow the UPS to charge from 4 to 6 hours

Résumé du contenu de la page N° 8

1111 W. 35th Street Chicago, IL 60609 USA Customer Support: (773) 869-1234 www.tripplite.com 93-1503 (9911081) 8 9911081 230V Smartpro 2200T OM.p65 8 11/24/99, 12:00 PM