Résumé du contenu de la page N° 1
Owner’s Manual
™
SmartOnline
Rack/Tower Mount On-Line UPS Systems
Not suitable for mobile applications.
Important Safety Instructions 2
Installation 3
Basic Operation 7
Troubleshooting 11
Battery Replacement 13
Storage and Service 14
Warranty Registration 14
Español 15
Français 29
1111 W. 35th Street Chicago, IL 60609 USA
Customer Support: (773) 869-1234 • www.tripplite.com
™
Copyright © 2009 Tripp Lite. All rights reserved. SmartOnline is a trademark of Tripp Lite.
Warranty Registration:
Résumé du contenu de la page N° 2
Important Safety Instructions SAVE THESE INSTRUCTIONS This manual contains instructions and w arnings that should be follo wed during the installation, operation and storage of all T ripp Lite UPS Systems. F ailure to heed these w arnings will v oid your w arranty . UPS Location Warnings • Install your UPS indoors, a w ay from e xcess moisture or heat, conducti v e contaminants, dust or direct sunlight. • F or best performance, k eep the i
Résumé du contenu de la page N° 3
Installation Mounting Rack Mount your equipment in either a 4-post or 2-post rack or rack enclosure (see ne xt page for 2-post mounting). The user must determine the f itness of hardw are and procedures before mounting. If hardw are and procedures are not suitable for your application, contact the manuf acturer of your rack or rack enclosure. The procedures described in this manual are for common rack and rack enclosure types and m
Résumé du contenu de la page N° 4
Installation (continued) 2-Post (Telecom) Mounting If you mount 2U UPS models in 2-post racks, the y require the addition of a T ripp Lite 2-Post Rackmount Installation Kit (model: 2POSTKITRMWM, sold separately). See Installation Kit o wner’ s manual for installation procedure for 2U UPS models. Mounting (Tower) Y our UPS can be mounted in an upright to wer position with optional base stands sold separately by T ripp Lite (Model # 2-9UST A
Résumé du contenu de la page N° 5
Installation Important (contin Safety ued) Instructions Connection and Start-Up 1 Plug your UPS’s line cord into an electrical outlet. Y our UPS must be connected to a dedicated circuit of suf f icient amperage. Note, ho we v er , that the select models may be f itted with dif ferent plug types. Refer to the “OP Rating/ Plug Rating” chart printed on the top of your UPS. Your model may differ. Once your UPS is plugged in, the f an and all 1 Indica
Résumé du contenu de la page N° 6
Installation (continued) Optional Connections (continued) 2 USB and RS-232 Serial Communications (all models) 2a Use the included USB cable (see ) and/or 2b DB9 serial cable (see ) to connect the communication port of your computer to the communication port of your UPS. Install on your computer the T ripp Lite Po werAlert S o f t w a r e a p p r o p r i a t e t o y o u r c o m p u t e r ' s 2a Your model may differ. operating system. Y our U
Résumé du contenu de la page N° 7
Basic Operation Front Panel Switches “ON/TEST” Button: This switch controls four separate UPS functions: UPS Power ON T o turn the UPS on, press this b utton, hold it for se v eral seconds until you hear a beep, then release it. The “ON LINE” LED will illuminate. UPS Self-Test During normal on-line operation, press this b utton and hold it until you hear a beep. This initiates a 10-second self-test of the battery . The UPS wi
Résumé du contenu de la page N° 8
Basic Operation (continued) Front Panel Indicator Lights continued “BYPASS” LED: This yello w light will flash to indicate that the UPS’ s DC/A C in v erter is deacti v ated and the UPS is in the “Bypass” mode. During normal operation this LED will light briefly when the unit is plugged in, b ut if an internal f ault or o v erload occurs this light will flash constantly and the f ault LED will illuminate to sho w that connected equipme
Résumé du contenu de la page N° 9
Basic Operation (continued) Front Panel Indicator Lights continued “REPLACE BATT” LED: T h i s r e d l i g h t w i l l i l l u m i n a t e c o n s t a n t l y and the UPS alarm will beep e v ery 2 seconds if your UPS’ s microprocessor detects a battery f ault or if your UPS f ails the automatic self-test (after you turn your UPS ON) and the UPS battery is less than fully char ged. Let the UPS system char ge for at least 12 h o u r s
Résumé du contenu de la page N° 10
Basic Operation (continued) Rear Panel continued Input Cord: This permanently attached po wer cord connects your UPS to a po wer outlet. AC Receptacles (Varied by Model): These 15-, 20- and 30-amp receptacles pro vide your connected equipment with pure sine-w a v e A C output from the A C line during normal operation and from battery po wer during black outs and se v ere bro wnouts. Po wer pro vided at these outlets is f iltered to protect con
Résumé du contenu de la page N° 11
Troubleshooting The UPS’ s control panel lights will turn on in the sequences belo w to signal that the UPS is ha ving operational dif f iculties. Lights (On/Flashing) and Condition Solution On: REPLACE BATT Let the UPS system charge for at least Condition: Replace Battery 12 hours and perform a self test using the "ON/Test Switch" as described on page 7. If the light continues to stay on, contact Tripp Lite for service. On: BATT LOW, ON BATT Prepare for imminent U
Résumé du contenu de la page N° 12
Troubleshooting (continued) Lights (On/Flashing) and Condition Solution On: BYPASS, LINE Check the UPS to be sure that there is Flashing: FAULT adequate space for air to circulate near Condition: On Bypass due to High the vents and that the fan is working Internal Temperature properly. Restart the UPS. Flashing: LINE This indicates that utility power is too high Condition: Input Abnormal or low for the UPS to operate in BYPASS mode, so if an inverter failure occurs, the UPS will
Résumé du contenu de la page N° 13
Battery Replacement Battery Replacement Door: Under normal conditions, the original battery in your UPS will last se v eral years. Battery replacement should be performed only by qualif ied service personnel. Refer to “Battery W arnings” in the Safety section. Should your UPS require battery replacement, visit T ripp Lite on the W eb at www .tripplite.com/support/battery/inde x.cfm to locate the specif ic replacement battery for your UPS. Pr
Résumé du contenu de la page N° 14
Storage and Service Storage First turn your UPS OFF: press the “OFF” switch to turn po wer of f at the UPS outlets, then disconnect the po wer cord from the w all outlet. Ne xt, disconnect all equipment to a v oid battery drain. If you plan on storing your UPS for an e xtended period of time, fully rechar ge the UPS batteries once e v ery three months by plugging the UPS into a li v e A C outlet and letting the UPS char ge fo
Résumé du contenu de la page N° 15
1111 W. 35th Street, Chicago, IL 60609 USA 773.869.1234 (USA) • 773.869.1212 (International) www.tripplite.com
