Résumé du contenu de la page N° 1
Résumé du contenu de la page N° 2
Electrical Connection Electrical ground is required on this appliance. 3 Prong Grounding Type Wall Receptacle Recommended grounding method: 3 Prong For your personal safety, this appliance must be Grounding Plug grounded. This air conditioner includes a power supply cord with a 3-prong grounding plug. To minimize possible electrical shock hazard: -cord must be plugged into a mating 3-prong grounding-type wall receptacle, Grounding prong -must be grounded in
Résumé du contenu de la page N° 3
3 1. Make sure you have all the necessary parts. 1 9,10,11 Installation kit contents: 1. Platform (1) 2. Support brace (1) 3. Adjustment bolt (1) 2 4. Hex flange nut - 1/4" (1) 8 5. Track seal (1) 6. Side channel seal (1) 13 12 7. Foam seal strip/Sash seal 8. Safety bracket (1) 17 5 9-11. Screw - #10 x 2-1/2" flat-head (2), OR 7 4 Screw - #10 x 1-3/4" pan-head (2), OR Screw - #10 x 1" pan-head (2) 16 12. Screw - #8 x 3/4" pan head (6)
Résumé du contenu de la page N° 4
3. Choose the proper window location. Choose a window that allows the cooled air to flow freely and directly into room(s) you wish to cool. Remember, it is difficult to move air around corners. Also, choose a window that is within 6 feet of an electrical outlet. (See Meeting Electrical Requirements/Receptacle wiring needs.) Do not use an extension cord. 6 foot power cord reach Installing Unit in a Sliding Window 1. Attach support brace to platform as shown. Use adjustment bolt and hex flange
Résumé du contenu de la page N° 5
Apply track seal 4. Peel off protective backing from track seal. Apply to window side seal to room side of window track. Center of seal strip of track. should coincide with the line marked in Step 2. The two screw holes drilled in Step 3 should be directly above seal strip in the inner track. 5. Securely attach a siding-protection board to side of house. NOTE: Siding-protection board should be long enough to span 2 wall studs. Inside wall of house Siding-protection board 6. Place platfo
Résumé du contenu de la page N° 6
10. Clamp plastic window panel between a board and a work table, and cut along cutting line with a fine tooth saw. Remove any burrs with a file. Fastening Side Channels 11. Fasten side channels to the sides of the AC using 3 screws (Item 17) per channel. Start with first screw at top of channel. Make sure hook ends of channels face toward back of unit. 12. Slide plastic window panel into panel frame, Panel frame with the smooth side to the room. Slide panel frame assembly into side channel
Résumé du contenu de la page N° 7
16. Slide inner window sash firmly against side of the cabinet. Make sure not to peel the seal strips from the window track and cabinet side channels. If the panel frame does not fit snugly to the inner window sash, secure the panel frame to the sash with #8x3/4-inch screws, or #8-32x3/4-inch self- Slide inner threading screws. Use the partially plugged holes in window sash firmly against the panel frame. Drill 1/8-inch pilot holes for the Cabinet. screws. 17. Hook the safety bracket over
Résumé du contenu de la page N° 8
Installing the Unit in a Casement Window NOTE: Open the window the maximum amount to allow for clearance of the cabinet. The crank handle should be removed to allow the platform to be fastened to the jamb. If the window cannot open far enough (more than 15-1/2 inches) for the cabinet to clear the window, remove the window entirely by drilling out the rivets. Bolts can serve as the pivots in the future. To avoid crank handle and window clearance problems, the unit can be installed in a st
Résumé du contenu de la page N° 9
Rear is at least 5. Adjust the platform assembly so that the rear of 7/16" lower the air conditioner will be 3/16-inch lower than the than front front. This ensures proper water drainage from the air conditioner. NOTE: A projection below the base of the air conditioner will require the rear of the platform to be 7/16-inch lower than the front to create the 3/16-inch slant from front to rear. 6. Securely attach a siding-protection board to the side of the house where the platform assembl
Résumé du contenu de la page N° 10
11. Cut side channel seal into 2 equal lengths. Remove the protective backing and apply it to the rear side of the cabinet side channels, starting just below the panel frame assembly. Pinch off excess length so the seal is even with the bottom of the cabinet side channel. Apply weather seal to side channels just below edge of panel frame. 12. To remove front 1. Remove the two front retaining screws from the front frame. 2. Press firmly on each side of the metal case close to the f
