Résumé du contenu de la page N° 1
1675 MacArthur Blvd., Costa Mesa, CA, 92626 USA
Main Number (714) 754-6175 or toll free (USA only) (800) 854-4079
Customer Service(714) 957-7150 or toll free (USA only) (800) 772-2834
HPR Series Powered Loudspeaker Products
User Manual
HPR153F 15-inch three-way
HPR152F 15-inch two-way
HPR151W 15-inch subwoofer
HPR181W 18-inch subwoofer
*TD-000212-01*
TD-000212-01 rev.D
Résumé du contenu de la page N° 2
Important Safety Precautions & Explanation of Symbols Install in accordance with QSC Audio Product's instructions and under the supervision of a licensed Professional Engineer. WARNING! CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous” voltage within the p
Résumé du contenu de la page N° 3
Introduction Congratulations and thank you for your purchase of this professional, powered loudspeaker product. To get the most from your invest- ment, we recommend you review all the information provided in this User Manual. The HPR self-powered loudspeakers provide excellent sound quality, durable construction and clean, efficient, on-board amplification. Amplifiers are matched to the drivers with active equalization and precise crossover control. Active power limiting and thermal man- agemen
Résumé du contenu de la page N° 4
HPR151W Features HPR181W Features 1- Pole Cup 4- Power Amplifier 2- Handles (2 each) 5- Slip-resistant Feet (4 each) 3- Grill 6- Casters (HPR181W only) Full Range Amplifier Detail Subwoofer Amplifier Detail 1- Input and Output Connector(s) 6- Power Switch 2- Gain Control 7- Circuit Breaker 3- Power, Signal, and Clip LED Indicators 8- Serial Number Plate 4- Front LED Switch 9- IEC Power Inlet 5- 100 Hz Low-Cut Filter Switch (Full Range Only) 10- Phase switch (Subwoofer Only) 4
Résumé du contenu de la page N° 5
Installation HPR152F WARNING! Do not use a loudspeaker support pole longer than 26” (660mm) when supported by the HPR151W or HPR181W subwoofer. Do not rig, fly or suspend this loudspeaker product! Before placing or installing any speaker product, inspect all hardware, suspension, cabinets, transducers, brackets and associated equipment for damage. Any missing, corroded, deformed, or non-factory component could significantly reduce the strength of the installation, placement or array. Any such
Résumé du contenu de la page N° 6
AC Mains AC power switch Connect AC power to the IEC socket on the back of the amplifier by locating the IEC connector-end of the AC power cord and inserting it fully into the IEC inlet on the power amplifier module. NOTE: Turn off the AC power switch before connecting AC power. The correct AC line voltage is shown on the serial number label, on the rear panel. Connecting to the wrong line voltage may damage the amplifier or increase the risk of electric shock. AC Mains Disconnection Turn the
Résumé du contenu de la page N° 7
Input Connections (continued) Full-range loudspeaker’s Input (IN) HPR152F and HPR153F: Insert the male XLR input into the jack marked FULL RANGE and Output (OUT) Connectors LINE IN. Ensure the connector is fully seated. HPR151W and HPR181W: Insert the left channel’s XLR input into the left channel’s (L) FULL RANGE LINE IN connector. Insert the right channel’s XLR connector into the right channel’s (R) FULL RANGE LINE IN connector. If a single input signal is used, plug into either the L (l
Résumé du contenu de la page N° 8
Output Connections (continued) HPR151W and HPR181W FULL RANGE LINE OUT: Use the outputs marked FULL RANGE LINE OUT (Left and/or Right) when connecting to down-stream powered loudspeakers which accept full-range audio or have their own filtering. 100 Hz LOW-CUT: Use the outputs marked 100 Hz LOW-CUT OUT (L and/or R) when connecting to downstream powered loudspeakers that have no low-frequency filtering but the low-frequency roll-off is desired. Do not use the 100 Hz LOW-CUT OUT connectors for
Résumé du contenu de la page N° 9
100 Hertz Low-Cut Filter Switch (HPR152F and HPR153F) 100 Hertz low-cut filter Below the LED indicators is a small recessed slide-switch that enables or disables a 100 Hertz low-cut filter. switch off and on positions Filter OFF (Full Range) Turn the filter OFF when using without subwoofers or dedicated low-frequency enclosures. Filter ON (100 Hz Low-Cut) Turn the filter ON when using with optional subwoofers or low-frequency systems. This results in less distor- tion at low frequencies and pr
Résumé du contenu de la page N° 10
SIGNAL Indicator LED The green SIGNAL indicator alerts the user to the presence of an input signal to the HPR loud- speaker. Normal Indication The green SIGNAL indicator illuminates when the input signal exceeds -25 dB. If No Indication Check Gain settings and increase gain if necessary. Check input connections and audio source for signal. If the red LIMIT LED illuminates, refer to the LIMIT indicator section, below. Abnormal Indication If the green SIGNAL LED illuminates with no signal input,
Résumé du contenu de la page N° 11
Application Example #1 Application Example #1 physical diagram. This example shows a two-channel (stereo) setup utilizing two top-boxes. Audio signals for the Left and Right channels are supplied by Channel 1 Channel 2 the mixer console. This signal source can be just about any or or variable-output level audio source, such as DJ mixers, profes- Left Channel Right Channel sional CD players, or computer-based audio signal sources. Audio output from the mixer’s Left channel is connected to the
Résumé du contenu de la page N° 12
Application Example #2 Application Example #2 physical diagram. This example shows a two-channel (stereo) setup utilizing one subwoofer and two top-boxes. Audio signals for the Left and Right channels are supplied by the mixer console. This signal source can be just about any variable-output level audio source, such as DJ mixers, profes- Channel 2 Channel 1 sional CD players, or computer-based audio signal sources. or or Right Channel Left Channel Audio output from the mixer is connected to
Résumé du contenu de la page N° 13
Application Example #3 Application Example #3 physical diagram. This example shows a two-channel (stereo) setup utiliz- ing two subwoofers and two top-boxes. Audio signals for the Left and Right channels are supplied by the mixer console. This signal source can be just about any variable-output level audio source, such as DJ mix- ers, professional CD players, or computer-based audio signal sources. Audio output from the mixer is connected to the sub- woofer input of each channel. Each subwoof
Résumé du contenu de la page N° 14
Application Example #4 This example shows a two-channel (stereo) setup utilizing two sub- woofers and multiple top-boxes. Channel 2 Channel 1 This is the same as Application or or Example #3 except an additional Right Channel Left Channel top-box has been added to each channel (and more could be added). To connect to additional top-boxes, connect a cable from the last top box’s FULL RANGE LINE OUT con- nector to the next top-box’s FULL RANGE LINE IN connector. Up to 20 top-boxes could b
Résumé du contenu de la page N° 15
Dimensions, HPR152F Dimensions, HPR153F 15
Résumé du contenu de la page N° 16
Dimensions, HPR151W Dimensions, HPR181W 16
Résumé du contenu de la page N° 17
Specifications, Full Range Models HPR152F HPR153F Frequency Response, ±6dB 53-18k Hz 42-19k Hz Frequency Range, -10dB limit 50-20k Hz 38-20k Hz Maximum Peak SPL 135dB 133dB Nominal coverage, H x V 90°x60° 90°x40° Directivity Index 9.4 11.1 Directivity Factor 8.7 12.9 Transducer Description 15” (381mm) transducer with 3” (76mm) voice coil 15” (381mm) transducer with 3” (76mm) voice coil 1” (25mm) throat compression driver 6.5” (165mm) transducer with 1” (25mm) voice coil 1” (25mm) throat compres
Résumé du contenu de la page N° 18
Specifications, Subwoofer Models HPR151W HPR181W Frequency Response, ±6dB 47-110 Hz 42-110 Hz Frequency Range, -10dB limit 43-140 Hz 39-140 Hz Maximum Peak SPL 133dB 134dB Nominal coverage, H x V Not applicable (N/A) Not applicable (N/A) Directivity Index 00 Directivity Factor 11 Transducer Description 15” (381mm) transducer with 3” (76mm) voice coil 18” (457mm) transducer with 4” (102mm) voice coil Amp Power 700 Watts 700 Watts Input Sensitivity 0.775 V (+0dBu) 0.775 V (+0dBu) rms rms Input He
Résumé du contenu de la page N° 19
Notes: 19
Résumé du contenu de la page N° 20
Warranty (USA only; other countries, see your dealer or distributor) Disclaimer QSC Audio Products, Inc. is not liable for any damage to amplifiers or any other equipment that is caused by negligence or improper installation and/or use of this loudspeaker product. QSC Audio Products 3 Year Limited Warranty QSC Audio Products, Inc. (“QSC”) guarantees its products to be free from defective material and / or workmanship for a period of three (3) years from date of sale, and will replace defectiv
