Résumé du contenu de la page N° 1
WS-7013U-IT
Wireless 915 MHz
Temperature Station
Instruction Manual
1
Résumé du contenu de la page N° 2
TABLE OF CONTENTS Topic Page Inventory of Contents Quick Setup Detailed Setup Guide Battery Installation Setting the Time Features Minimum and Maximum Temperatures Resetting Minimum and Maximum Temperatures Additional remote temperature sensors (optional) Mounting Troubleshooting Maintenance and Care Specifications Warranty Information 2
Résumé du contenu de la page N° 3
This product offers: INSTANT TRANSMISSION is the state-of- the-art new wireless transmission technology, exclusively designed and developed by LA CROSSE TECHNOLOGY. INSTANT TRANSMISSION offers you an immediate update (every 4 seconds!) of all your outdoor data measured from the sensors: follow your climatic variations in real-time! INVENTORY OF CONTENTS 1. The indoor temperature station (Figure 1) 2. The remote temperature sensor (TX29U- IT
Résumé du contenu de la page N° 4
Figure 1 Figure 2 ADDITIONAL EQUIPMENT (not included) 1. 1 Philips screwdriver. 2. 2 Fresh AAA 1.5V batteries. 3. 2 Fresh AA 1.5V batteries QUICK SETUP Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries. 1. Have the indoor temperature station and remote temperature sensor 3 to 5 feet apart. 2. Batteries should be out of both units for 10 minutes. 4
Résumé du contenu de la page N° 5
3. Place the batteries into the remote temperature sensor first then into the indoor temperature station. (All remote temperature sensors must be started before the indoor temperature station) 4. DO NOT PRESS ANY BUTTONS FOR 15 MINUTES. In this time the indoor temperature station and remote temperature sensor will start to talk to each other and the display will show both the indoor temperature and an outdoor temperature. If the indoor temperature station does not display both tempe
Résumé du contenu de la page N° 6
walls, floors, ceilings, thick trees, etc.) will effectively cut signal range in half. Example: A wireless weather station with a 330 feet range is mounted on an interior wall, so that the signal has to pass through one interior wall, one exterior wall, and across the 10 feet width of the room between the 2 walls. The first wall will reduce the range to 165 feet, and the second wall will reduce the range to 87 feet. Factoring in the 10 foot room, this leaves a maximum of 77 feet
Résumé du contenu de la page N° 7
To complete the set up of your indoor temperature station after the 15 minutes have passed please follow the steps below. 1. Press and hold the “SET/CH” button for 5 seconds. Note: A “12h” or “24h” will appear on the top line. (“12h” for AM/PM, “24h” for military time) 2. To change between “12h” and “24h” press and release the “MIN/MAX” button. 3. When you have your choice shown on the display press and release the “SET/CH” button once. Note: if “12h” is selected, the temperatur
Résumé du contenu de la page N° 8
6. When the correct hour is shown, press and release the “SET” button once. Press and release the SET button once more and you are done. DETAILED SETUP GUIDE BATTERY INSTALLATION - When one Temperature sensor is being used 1. First, insert the batteries to the Temperature sensor (see “A. Temperature sensor” below). 2. Within 2 minutes of powering up the sensor, insert the batteries to the Temperature Station (see “B. Indoor Temperature station” below). Once the batteries ar
Résumé du contenu de la page N° 9
data signal from the sensor. The outdoor temperature and humidity should then be displayed on the Temperature Station. If this does not happen after 2 minutes, the batteries will need to be removed from both units and reset from step 1 and the signal reception icon is no longer shown. A. REMOTE TEMPERATURE SENSOR Remove the mounting bracket. Battery a. Remove battery cover cover b. Observing the correct polarity, install 2 AA batteries—make sure they do not spring free, or s
Résumé du contenu de la page N° 10
a. Remove the battery cover on the backside. To do this, push up and pull out. Battery Cover b. Observing the correct polarity, install 2 AAA batteries. c. Replace battery cover. d. Wait 15 minutes to allow both the indoor and outdoor temperatures are shown on the indoor temperature station. 10
Résumé du contenu de la page N° 11
Sensor signal reception icon * * When the signal is successfully received by the Temperature Station, the icon will be switched on. (If not successful, the icon will not be shown in LCD) So the user can easily see whether the last reception was successful (icon on) or not (icon off). On the other hand, the short blinking of the icon shows that a reception is being done now. • If the signal reception is not successful on the first frequency (915MHz) for 4
Résumé du contenu de la page N° 12
910MHz. This will also be done for re- synchronization. SETTING THE TIME 1. Press and hold the “SET/CH” button for 5 second, “12h” will appear in the TIME LCD. 2. Press and release the “MIN/MAX” button to select either 12h time (am/pm) or 24h time 3. Press and release the “SET/CH” button 2 times, the hour will flash in the upper left corner. 4. Press and release the “MIN/MAX” button to set the hours 5. Press and release the “SET/CH” button to move to the minute setting
Résumé du contenu de la page N° 13
Note: if “12h” is selected, the temperature is displayed in degree Fahrenheit. If “24h” is selected, the temperature is displayed in degree Celsius FEATURES MINIMUM & MAXIMUM TEMPERATURES 1. Press and release the “MIN/MAX” button, “MIN” appears in the temperature LCD’s and the recorded minimum temperatures are displayed. 2. Press and release the “MIN/MAX” button to toggle to the maximum temperatures. RESETTING THE MINIMUM & MAXIMUM TEMPERATURES To reset both the minimum and
Résumé du contenu de la page N° 14
temperature sensor units with the WS-7013U- IT. These extra sensors can be purchased through the same dealer as this unit. 1. Remove all the batteries from the receiver and sensor(s) and wait 60 seconds. During these 60 seconds, press any button 20 times to discharge any excess power. 2. Insert the batteries to the first temperature sensor. 3. Within 2 minutes of powering up the first sensor, insert the batteries to the Temperature Station. Once the batteries are in place, all seg
Résumé du contenu de la page N° 15
5. Insert the batteries to the second sensor as soon as the outdoor temperature readings from the first sensor are displayed on the Temperature station. NOTE: You must insert the batteries into the second sensor within 45 seconds of reception of the first sensor. 6. The outdoor temperature from the second sensor and the "channel 2" icon should then be displayed on the Temperature station. If this does not happen after 2 minute, the batteries will need to be removed from all the u
Résumé du contenu de la page N° 16
NOTE: You must insert the batteries into the third sensor within 45 seconds of reception of the second sensor. IMPORTANT: Transmission problems will arise if the setting for multiple sensors is not followed as described above. Should transmission problems occur, it is necessary to remove the batteries from all units and start again the set-up from step 1. VIEWING AND OPERATING WITH MULTIPLE REMOTE TEMPERATURE SENSOR UNITS 1. To view the temperature of a different remote tempera
Résumé du contenu de la page N° 17
3. To reset the Minimum/Maximum readings, press and hold the “MIN/MAX” button for four seconds. MOUNTING Note: To achieve a true temperature reading, avoid mounting in direct sunlight. We recommend that you mount the remote temperature sensor on an outside North- facing wall. The sending range is 330ft; obstacles such as walls, concrete, and large metal objects will reduce the range. Place both units in their desired location before permanently mounting. 1. REMOTE TEMPERATURE
Résumé du contenu de la page N° 18
b. Mount using either screws or adhesive tape. c. Reattach the temperature sensor to the mounting bracket. 2. THE TEMPERATURE STATION e. The indoor temperature station comes with the table stand already mounted. If you wish to use the table-stand, all that is required is to place the indoor temperature station in an appropriate location. f. To wall mount, remove the table stand. To do this, pull down on the stand from the rear and rotate forward. Fix a screw (not included) i
Résumé du contenu de la page N° 19
Problem: The LCD is faint Solution: Replace batteries Problem: No outdoor temperature I displayed. Solution: 1) Remove all batteries, reinsert into remote temperature sensor first, and then into the indoor temperature station. 2) Place remote temperature sensor closer to the indoor temperature station. 3) Be sure all batteries are fresh. 4) Place remote temperature sensor and indoor temperature station in position so the straight-line signal is not passing through more than tw
Résumé du contenu de la page N° 20
The indoor sensor is less responsive to ambient air currents because of the shielding effect of the display's case. In addition, the case can act as a heat sink to absorb and store heat from external sources (i.e. handling of the case or radiant heat). In addition, the much greater range of the outdoor temperature sensor requires a different calibration curve than the indoor range. Error is usually greater at the extreme ends of a range, making it harder to compare different ranges wi
