Instruction d'utilisation Carrier SYSTXCC4ZC01

Résumé du contenu de la page N° 1

SYSTXCC4ZC01
Infinity Damper Control
Visit www.carrier.com
Installation and Start-Up Instructions
GER, WARNING, and CAUTION. These words are used with
the safety-alert symbol. DANGER identifies the most serious
hazards, which will result in severe personal injury or death.
WARNING signifies a hazard, which could result in personal
injury or death. CAUTION is used to identify unsafe practices,
which would result in minor personal injury or product and
property damage. NOTE is used to highlight su

Résumé du contenu de la page N° 2

 Zoning User Interface (p/n SYSTXCCUIZ01) — Each instal- LOCATING ZONING USER INTERFACE — The User Inter- lation has only 1 User Interface. This is the command center for face is the command center for the Infinity Zone System. It should the entire system. It will typically be located in Zone 1 to sense be located where it is easily accessible and visible to home or and control the temperature in this zone. If desired, a Remote business owner. It is also normally the Zone 1 sensor and as such R

Résumé du contenu de la page N° 3

Step 3— Install Components INSTALL INFINITY DAMPER CONTROL — The Infinity ELECTRICAL OPERATION HAZARD Damper Control is designed so that wires can enter it from behind, Failure to follow this caution will result in euipment damage above, or below. Plan wire routing before mounting Damper or improper operation. Control. Condensation can damage the actuator. When dampers are 1. Remove cover to access mounting holes. located in an unconditioned space, condensation is likely to 2. Mount back plate t

Résumé du contenu de la page N° 4

SET SCREW SET SCREW MOUNTING HUB FLEXIBLE ZONE 3/16" GAP DUCT DAMPER MOUNTING HUB ACTUATOR HOUSING PLASTIC COVER QUICK BLADE RELEASE CLS COM OPN Fig. 5 — Round Flexible Duct Work CLS COM A95132 OPN 1 / 2″ STEEL STRAP (CLS) CLOSED 3/16" (COM) COMMON GAP ANTI-ROTATION ANTI-ROTATION (OPN) OPEN MOUNTING SCREW MOUNTING SCREW (5/16") Fig. 1 — Damper 24-vac Connections C03024 1 / 2″ STEEL STRAP Fig. 6 — Insulated Round Flexible Duct Work A95133 FIBROUS FIELD GLASS SUPPLIED DUCTWORK SCREWS ZONE Fig. 2

Résumé du contenu de la page N° 5

NOT required for regular use. Traditionally, the LAT/HPT sensors FUSE — A 1-amp automotive type fuse is used to protect the were required for temperature / equipment monitoring. The Infin- Infinity Damper Control from over current on the damper drive ity Zoning System does not require these because the User outputs. If this fuse fails, damper wiring should be inspected for Interface algorithms will perform temperature and airflow man- shorts. Also, no more than five damper motors should be con-

Résumé du contenu de la page N° 6

ON 1 2 ON 1 2 2-spd. Outdoor A B C D Unit Zoning User Interface & Ventilator Smart Sensor(s) Unit ABCD Connection: Connection Y R G B A = Green: RS485+ Optional - Indoor B = Yellow: RS485- A B C D Leaving Air & Heat Pump Unit C = White: 24VAC (COM) A B C D Temperature Sensor D = Red: 24VAC (HOT) A B C D A B C D Y R G B LAT COM HPT Optional FUSE ZS1 Zone-1 CLS1 See Note _ Zone-1 ZS1C Sensor _ COM1 Damper OPN1 DIP Switch Zone-2 ZS2 CLS2 ZS2C Zone-2 OFF Sensor Dampers: COM2 Damper OPN2 CLS_ =

Résumé du contenu de la page N° 7

Damper Control Damper Control Module Module ZS_ ZS_C Sensor 1 Sensor 2 Sensor 3 Sensor 4 Fig. 11 — Remote Room Sensor Averaging 4-Sensor Application (series- parallel) A03233 TROUBLESHOOTING Zoning User Interface Display says, ″Outdoor Unit Not Found″, when applied with a two-speed communicating out- Zoning User Interface Control does not power up: door unit: 1. Recheck wiring to ABCD on all devices. Make sure all colors 1. Recheck wiring to ABCD connector on outdoor unit. Make match for every t

Résumé du contenu de la page N° 8

Copyright 2004 CARRIER Corp.  7310 W. Morris St.  Indianapolis, IN 46231 damp4zc1si Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations. Book 1 4 Tab misc. misc. PC 101 Catalog No. 809-50012 Printed in U.S.A. Form DAMP4ZC-1SI Pg 8 04-04 Replaces: NEW