Instruction d'utilisation JAI AD-081

Instruction d'utilisation pour le dispositif JAI AD-081

Dispositif: JAI AD-081
Catégorie: Caméra
Fabricant: JAI
Dimension: 0.46 MB
Date d'addition: 10/12/2014
Nombre des pages: 6
Imprimez l'instruction

Téléchargez

Comment utiliser?

Notre objectif consiste à vous assurer le plus rapide accès au contenu de l'instruction d'utilisation du dispositif JAI AD-081. En utilisant l'aperçu en ligne vous pouvez parcourir le sommaire et passer à la page où vous trouverez la résolution de votre problème avec JAI AD-081.

Pour votre confort

Si regarder l'instruction JAI AD-081 directement sur la page n'est pas confortable pour vous, vous pouvez profiter de deux solutions possibles:

  • Exploration au mode de plein écran - pour analyser l'instruction d'une manière commode (sans l'avoir téléchargée sur votre ordinateur) vous pouvez utiliser le mode d'exploration en plein écran. Pour démarrer l'exploration de l'instruction JAI AD-081 en plein écran, utilisez le bouton Plein écran.
  • Téléchargement sur l'ordinateur - vous pouvez aussi télécharger l'instruction JAI AD-081 sur votre ordinateur et la sauvegarder dans vos ressources. Si vous n'avez pas envie de gaspiller votre espace disque, vous pouvez toujours télécharger cette instruction du ManualsBase dans l'avenir.
JAI AD-081 Manuel d'utilisation - Online PDF
Advertisement
« Page 1 of 6 »
Advertisement
Version imprimée

Beaucoup de gens préfèrent de lire les documents dans la version imprimée et non pas sur l'écran. L'option d'impression de l'instruction est aussi prévue et vous pouvez en profiter en cliquant le lien ci-dessus - Imprimez l'instruction. Il n'est pas nécessaire d'imprimer toute l'instruction JAI AD-081 - on peut choisir des pages. Economisez le papier.

Résumés

Vous trouverez ci-dessous les annonces des contenus qui se trouvent sur les pages suivantes de l'instruction de JAI AD-081. Si vous voulez parcourir rapidement le contenu des pages suivantes de l'instruction, vous pouvez en profiter.

Résumés du contenu
Résumé du contenu de la page N° 1

Tech Note
TN-0902 Date: 02/06/09
UsiNg a 2CCD Camera To Crea Te HigH-DyNamiC raNge images
Some imaging scenarios push dynamic range beyond the capabilities of the typical sensor. This is especially
true where incident light is present (e.g., imaging a light source and the surrounding area). This can also
occur in situations with bright reflections or in high contrast indoor/outdoor scenes where one needs to cap-
ture details in both bright sunlight and dark shadows. One technique for

Résumé du contenu de la page N° 2

Tech Note Example 1 - Maximum Dynamic Range (no overlap) To create an image that spans the maximum range of light intensities, use shutter settings to calibrate the 2 sensors so that Sensor B = Sensor A * 1024. In other words, the light needed to generate 100 counts from Sen- sor B is 1024 times the light needed to create 100 counts from Sensor A. For example, if Sensor A is operating with the shutter off (1/30 sec.), Sensor B would need to be set as close as possible to 1/30720 sec. using th

Résumé du contenu de la page N° 3

Tech Note Displaying a high dynamic range image on a standard monitor will require mapping the output to fit the monitor’s dynamic range capability. For the image described above, start by creating a 20-bit image map using the raw pixel data. Then create a 10-bit image map to display on the monitor by dividing the 20-bit im- age map by 1024. Or create a 12-bit image map by dividing the 20-bit image map by 512. The preceding process describes using both output channels in 10-bit mode. Alternati

Résumé du contenu de la page N° 4

Tech Note Now, our post processing routine could be handled as follows: if (pixel B < 16){ pixel_out = pixel A }else{ pixel_out = pixel B * 64 } By overlapping the two sensor responses, this approach utilizes the full precision of the lower 10-bits while reducing the effect of noise at the transition point and greatly increasing the precision of the upper 6-bits. Example 3 – Averaging the Overlap Both of the preceding examples assume that a precise calibration can be made between

Résumé du contenu de la page N° 5

Tech Note Now as Sensor A approaches its saturation point (512 – 1023 counts) the output uses the average of both sen- sors’ data to “smooth” the transition between the two sensor response graphs (see Figure 6). It still limits the use of the lowest bits on Sensor B (those that are most susceptible to noise) and keeps the calibration factor at 64 to increase the output precision of the upper bits. FIGURE 6 – Averaging used to smooth calibration in overlapped region Example 4 – Dual-Slope Dyna

Résumé du contenu de la page N° 6

Tech Note For example, in a 4-bit overlap scenario, we still set the shutter for Sensor B to be roughly 64 times faster than Sensor A (i.e., a pixel on Sensor A with a value of 256 would have a value of 4 on Sensor B). But, de- pending on our objective, we apply a post processing factor of less than 64 and add an offset value to get the two output graphs to intersect somewhere around 768 counts. Finally, use a post processing algorithm that averages the values of Sensor A and B in the last bit


Instructions pareilles
# Instruction d'utilisation Catégorie Téléchargez
1 JAI TS-4032EN Manuel d'utilisation Caméra 0
2 JAI TM-1020 Manuel d'utilisation Caméra 0
3 Dodge TXT/HXT 709 - 715 - 725 Manuel d'utilisation Caméra 0
4 Sony 3-286-590-12(1) Manuel d'utilisation Caméra 29
5 Sony 3CCD COLOR BRC-300P Manuel d'utilisation Caméra 56
6 Sony 4-157-878-12(1) Manuel d'utilisation Caméra 0
7 Sony 300PF Manuel d'utilisation Caméra 8
8 Sony 300PK Manuel d'utilisation Caméra 9
9 Sony 3-280-847-11(1) Manuel d'utilisation Caméra 1
10 Sony 3CCD COLOR BRC-300 Manuel d'utilisation Caméra 16
11 Sony 4-114-858-12(1) Manuel d'utilisation Caméra 2
12 Sony 4-191-794-11(1) Manuel d'utilisation Caméra 1
13 Sony 9032PW Manuel d'utilisation Caméra 0
14 Sony a (alpha) SLT-A57 Manuel d'utilisation Caméra 79
15 Sony a (alpha) SLT-A55 Manuel d'utilisation Caméra 143