Résumé du contenu de la page N° 1
PE2300
848AB193A0 (705)
G G
B B
OWNER’S MANUAL
WATER PUMP
PE2300
GB-1
Résumé du contenu de la page N° 2
PE2300 SAFETY PRECAUTIONS Contents Warning labels bearing the mark on the product and in this Manual refer to important safety matters. Please familiarize your- self with them and observe them well. 1. Parts location .................................................. 2 If a warning label on the product becomes soiled or detached, 2. Specification ................................................... 3 please order a replacement label from your dealer and attach it 3. Symbols in the manual .......
Résumé du contenu de la page N° 3
PE2300 2. Specification Model name PE2300 Application Fresh water or agricultural water Dry weight ∗ (kg) 4.7 External dimensions of main unit 288x221x321 G (length x width x height) ∗ (mm) B Pump Type Self suction type volute pump Suction/Discharge port diameter (mm) 25 Total water head Discharge (m) 35 Suction (m) 8 Discharge(Max) (L/min) 92 Max temperature for usage (°C) 75 Engine Type Single-cylinder air-cooled 2-cycle gasoline engine Model number Zenoah G23LH Exhaust capacity (cc) 22.5 Fue
Résumé du contenu de la page N° 4
PE2300 5. For safe operation Before using this product, please read this Operator's • When using for the first time, before commencing Manual thoroughly to ensure correct operation. The fol- actual operating please receive guidance in operating lowing are precautions that should be observed in order the product from a person with adequate experience. to use the product smoothly. Elsewhere in the Manual, • Please take good care of this Operator's Manual and the warning mark is used to bring yo
Résumé du contenu de la page N° 5
PE2300 5. For safe operation PRECAUTIONS CONCERNING FUEL MAINTENANCE PRECAUTIONS • The engine of this product is fueled by "mixed gaso- • In order to maintain the functions of the product, regu- line" that includes highly combustible fuel. Do not re- larly carry out the maintenance inspections listed in fuel or store fuel containers where there is any risk of this Manual. When maintenance or parts replacement combustion from incinerators, burners, bonfires, not indicated in this Manual are req
Résumé du contenu de la page N° 6
PE2300 6. Set up IMPORTANT NOTE Discharge port angle can be changed to 3 different • As a suction hose, be sure to use suction hose(nominal directions. Adjust to your operating condition. diameter 25mm) or an equivalent ‘water suction hose’ only. 4. Submerge the suction hose strainer in the water. • Securely connect hoses with attached hose couplings 5. Lay the discharge hose where necessary. Arrange and clumps. protective covers if the hose can be disturbed by foot • If the suction hose con
Résumé du contenu de la page N° 7
PE2300 7. Fuel 5. Put a clear indication on the outside of the container 2. GASOHOL – It can cause deterioration of rubber and/ to avoid mixing up with gasoline or other containers. or plastic parts and disruption of engine lubrication. 6. Indicate the contents on outside of container for easy 3. OIL FOR 4-CYCLE ENGINE USE – It can cause spark identification. plug fouling, exhaust port blocking, or piston ring stick- ing. ■ FUELING THE UNIT 4. Mixed fuels which have been left unused for a peri
Résumé du contenu de la page N° 8
PE2300 8. Operation 1. Press the primer at the bottom of the carburetor a few IMPORTANT times with your finger until the fuel starts to flow through the transparent pipe. • If the rope is pulled continuously with the choke closed, the spark plugs may become flooded and the engine may fail b a. air cleaner to start. If so, you should first remove the spark plugs and a b. choke lever dry the electrodes, then repeat the starting procedure. c c. close d. open 5. Operate the engine at a half th
Résumé du contenu de la page N° 9
PE2300 9. Maintenance Every Every Every 25 50 100 Before System/components Procedure Note hours hours hours use after after after fuel leaks, fuel spillage wipe out ✔ G fuel tank, air filter, fuel filter inspect/clean ✔✔ replace, if necessary B see adjusting replace carburetor idle speed adjuster ✔ idling speed if necessary clean and readjust GAP: 0.6 to 0.7 mm (.025 in) spark plug ✔ plug gap replace, if necessary cylinder fins, intake air cooling vent clean ✔ muf
Résumé du contenu de la page N° 10
PE2300 9. Maintenance • When replacing plugs, please use designated items. NOTE •Warm up the engine before adjusting the idling speed. • Throttle wire play Throttle wire play should be 1 to 2 mm. After com- pletely returning the throttle lever, take the throttle wire CHAMPION CJ-6Y at the carburetor end in your fingers and give a light tug. If the play is too great or too small, readjust the IMPORTANT position of the wire retaining nut. Loosen the lock nut and turn the wire retaining nut clo
Résumé du contenu de la page N° 11
PE2300 9. Maintenance INTAKE AIR COOLING VENT IMPORTANT WARNING • If waste gets stuck and causes blockage around the intake air cooling vent or between the cylinder fins, it • Never touch the cylinder, muffler, or spark plugs with may cause the engine to overheat, and that in turn G your bare hands immediately after stopping the en- may cause mechanical failure on the part of the B gine. The engine can become very hot when in op- brushcutter. eration, and doing so could result in severe bur
Résumé du contenu de la page N° 12
PE2300 12. Troubleshooting guide Case 1. Starting failure CHECK PROBABLE CAUSES ACTION fuel tank → incorrect fuel → drain it and use correct fuel fuel filter → fuel filter is clogged → clean carburetor adjustment screw → out of normal range → adjust to normal range sparking (no spark) → spark plug is fouled/wet → clean/dry → plug gap is incorrect → correct (GAP: 0.6 to 0.7 mm) spark plug → disconnected → retighten Case 2. Engine starts but does not keep running/hard re-starting CHECK PROBABLE CA
Résumé du contenu de la page N° 13
PE2300 Limited warranty Should any failure occur on the product under normal oper- NOT REDUCE THE WARRANTY OBLIGATION OF THE ating conditions within the applicable warranty period, the COMPANY. failed part will be replaced or repaired free of charge by a ZENOAH authorized dealer. THE COMPANY IS LIABLE FOR DAMAGES TO OTHER ENGINE COMPONENTS CAUSED BY THE FAIRURE OF A G WARRANTY PERIOD: 1 year (6 months if used profession- WARRANTED PARTS STILL UNDER WARRANTY. ally, and 30 days if used for rental
