Instruction d'utilisation Axor Uno 38210XX1

Résumé du contenu de la page N° 1

Installation Instructions / Warranty
Axor Uno
38020XX1
Axor Uno
38025XX1
Axor Uno
38210XX1

Résumé du contenu de la page N° 2

Uno Single-control Lavatory Faucet 38020XX1 Uno Single-control Tall Lavatory Faucet 38025XX1 Uno Single-control Bidet Faucet 38210XX1 38020XX1 38025XX1 38210XX1 Technical Information Installation Considerations Recommended water pressure 14.7 - 72.5 psi • For best results, Hansgrohe Max. water pressure 145 psi recommends that this unit be Recommended hot water temp. 120° - 140° F* installed by a licensed, profes- Max. hot water temp 176° F* sional plumber. Hole size in mounting surface 1 3/8"

Résumé du contenu de la page N° 3

Installation Place the faucet and sealing ring on the mounting surface. Install the friction washer, metal washer, and mounting nut. Tighten the mounting nut by hand. Check the position of the faucet. When satisfied, use a slot-headed screwdriver to tighten the tensioning screws. Install the drain pull rod. Connect the hot and cold supply lines to the stops. Use two wrenches, as shown in the diagram, to prevent hose twisting. Install the drain. Set the high temperature limit stop (optio

Résumé du contenu de la page N° 4

Set the high temperature limit stop (optional) Remove the screw cover, located on the back of the handle. Use a 4 mm allen wrench to loosen the screw. Remove the handle Remove the flange and the green high temperature limit stop ring. Install the high temperature limit stop ring so that the black positioning pin is in the notch corresponding to the desired high temperature. The temperatures shown in the diagram assume an incoming cold water temperature of 50°F and an incoming hot water

Résumé du contenu de la page N° 5

Install the pop-up drain Remove the plunger assembly. Unscrew the drain outlet flange from the tee. Unscrew the tailpiece from the tee. Wrap the threads with Teflon tape and replace. Install the white, flexible sealing gasket to the flange. Place it in the sink outlet. Install the black mack gasket, white friction ring and retainer nut on the flange. Do not tighten the nut against the bottom of the sink at this time. Thread the tee and tailpiece to the flange. The pivot must face the

Résumé du contenu de la page N° 6

User Instructions Pivot the handle back to turn the water on, and forward to turn the water off. Pivot the handle to the left to make the water warmer, to the right to make the water cooler. Replacement Parts 1.1 1 1.2 2 3 8 9 4 5 10 1 handle 38094XXX 1.1 screw cover 96762000 1.2 set screw 96029000 2 flange 96763XXX 3 nut 97209000 4 cartridge 96764000 6 5 seal 95008000 6 aerator 97370XXX 7 fixing set 13961000 8 pull rod 96657000 9 ball joint 96050XXX 7 10 aerator 94005XXX 11 supply hose – 470 mm

Résumé du contenu de la page N° 7

Cleaning Recommendation for Hansgrohe Products Modern lavatory faucets, kitchen faucets, and showers consist of very different materials to comply with the needs of the market with regard to design and functionality. To avoid damage and returns, it is necessary to consider certain criteria when cleaning. Cleaning Materials for Faucets and Showers Acids are a necessary ingredient of cleaning materials for removing lime, however please pay attention to the follow- ing points when cleaning fauce

Résumé du contenu de la page N° 8

THIS WARRANTY DOES NOT COVER, AND HANSGROHE WILL NOT PAY FOR: A. Conditions, malfunctions or damage not resulting from defects in material or workmanship. B. Conditions, malfunctions or damage resulting from (1) normal wear and tear, improper installation, improper maintenance, misuse, abuse, negligence, accident or alteration, or (2) the use of abrasive or caustic cleaning agents or “no-rinse” cleaning products, or the use of the product in any manner contrary to the product instruc- tions. (