Instruction d'utilisation Asus M2NC61S

Résumé du contenu de la page N° 1

U2811
V-Series M2NC61S
ASUS PC (Desktop Barebone)
Installation Manual

Résumé du contenu de la page N° 2

Refer to the system user guide for installation details and other system information from ASUS website. Front panel features 5 . 2 5 - i n c h d r i v e bay cover 3 . 5 - i n c h d r i v e b a y cover This V-series Headphone port provide V2/V3 two types of Microphone port front panel for users to choose, USB 2.0 ports please refer to your product HDD LED package for the front panel type Reset button you purchased. Power button Rear panel features Power connector Voltage selector Pow

Résumé du contenu de la page N° 3

eSATA Internal components 5 2 3 6 1 7 4 M2N-NM 8 9 10 11 12 1. Front panel cover 8. ASUS motherboard 2. 5.25-inch optical drive bays 9. PCI Express x16 slot 3. Hard disk drive bay 10. PCI Express x1 slot 4. Floppy disk drive bay 11. PCI slots 5. Power supply unit 12. Metal bracket lock 6. CPU socket 7. DIMM sockets Selecting the voltage The system’s power supply unit has a 115 V/230 V voltage selector switch located beside the power connector. Use this switch to select the appropriate syste

Résumé du contenu de la page N° 4

Removing the side cover and front panel assembly 1. Remove the cover screws on the rear panel. 2. Pull the side cover toward the rear panel until its hooks disengage from the chassis tabs. Set the side cover aside. 3. Locate the front panel assembly hooks, then lift them until they disengage from the chassis. 4. Swing the front panel assembly to the right, until the hinge-like tabs on the right side of the assembly are exposed. 5. Remove the front panel assembly, then set aside. 4 4 3 Air du

Résumé du contenu de la page N° 5

2. Install the CPU to the socket, making sure that the CPU cornes with the gold triangle matches the socket corner with a small triangle. 3. Push down he socket lever to secure the CPU. Installing the CPU fan and heatsink assembly 1. Place the heatsink on top of the installed CPU, making sure that the heatsink fits properly on the retention module base. 2. Attach one end of the retention bracket to the retention module base. 3. Align the other end of the retention bracket (near the retention

Résumé du contenu de la page N° 6

Installing a DIMM 1. Locate the DIMM sockets in the motherboard. 2. Unlock a DIMM socket by pressing the retaining clips outward. 3. Align a DIMM on the socket such that the notch on the DIMM matches the break on the socket. 4. Push the DIMM to the socket until the retaining clips snap inward. • Unplug the power supply before adding or removing DIMMs. Failure to do so may cause damage to the motherboard and/or components. • A DDR2 DIMM is keyed with a notch so that it fits in only one di

Résumé du contenu de la page N° 7

Installing storage drives Optical drive 2 1. Place the chassis upright, then remove the upper 5.25” drive 3 3 bay metal plate cover. 2. Insert the optical drive to the bay, then carefully push the drive until its screw holes align with the holes on the bay. 3. Secure the optical drive with two screws on both sides of the bay. 4. Connect the IDE (A) and power (B) plugs to connectors at the B back of the drive. A Floppy disk drive 1. Place the chassis upright, then remove the lower 3.5” dr

Résumé du contenu de la page N° 8

4. For SATA HDD: Connect the SATA IDE SATA signal and power plugs to the connectors at the back of the drive. For IDE HDD: Connect the IDE signal and power plugs to the connectors at the back of the drive. Removing the bay covers and reinstalling the front panel assembly and side cover If you installed an optical and/or floppy disk drive, remove the bay cover(s) on the front panel assembly before reinstalling it to the chassis. To do this: 1. Locate the bay cover locks. 2. Press the loc