Résumé du contenu de la page N° 1
S O L O I I
USER MANUAL
SILENCE RENEWED
Résumé du contenu de la page N° 2
SOLO II USER’S MANUAL Congratulations on your purchase of the Antec SOLO II. The SOLO II emphasizes Quiet Computing™ and reinvents Antec’s renowned Sonata line with a new set of attractive, practical features. Externally, the SOLO II’s dual-layer 1.0 mm SECC / polycarbonate top & side panels absorb noise for exceptional sound dampening. To reduce vibration-related noise, the dual hard drive mounting system gives you the option of mounting your hard drives using tray mounts with silicon
Résumé du contenu de la page N° 3
TABLE OF CONTENTS SECTION 1: INTRODUCTION 1.1 Getting to Know your Chassis ..................................................................5 1.2 Chassis Specifications...............................................................................6 1.3 Included Screws .......................................................................................6 1.4 Before you Begin ......................................................................................7 SECTION 2: HARDWARE IN
Résumé du contenu de la page N° 4
SECTION 1 INTRODUCTION 4
Résumé du contenu de la page N° 5
1.1 GETTING TO KNOW YOUR CHASSIS 8 3 4 1 6 5 7 2 8 9 1. Internal: 3 x 3.5” / 2.5”using tray mount OR 2 x 3.5” with suspension mount cables 2. Internal: 1 x 2.5” SSD (dedicated) 3. External: 2 x 5.25” 4. 1 x rear 120 mm TrueQuiet™ fan with 2-speed switch 5. 2 x front 120 mm fans (optional) and removable, washable air filters 6. Anodized aluminum front bezel 7. Front ports 8. Power supply mount 9. 7 expansion slots 5
Résumé du contenu de la page N° 6
1.2 CHASSIS SPECIFICATIONS Chassis Type Mid Tower Chassis Color Piano Black 17.3” (H) x 8.1” (W) x 18.5” (D) Dimensions 440 mm (H) x 205 mm (W) x 470 mm (D) Weight 20.2 lbs / 9.1 kg Cooling - Rear 120 mm TrueQuiet™ fan with preinstalled silicone grommets and 2-speed switch - 2 front 120 mm fan mounts (optional) - 3 x 3.5”/2.5” using tray mounts with preinstalled silicone grommets Drive Bays OR 2 x 3.5” with suspension mounting system - 2 x external 5.25” - 1 x 2.5” (dedica
Résumé du contenu de la page N° 7
1.4 BEFORE YOU BEGIN In order to ensure that your building experience with the SOLO II will be a positive one, please take note of the following: • While working inside your SOLO II, keep your chassis on a flat, stable surface. Make sure your build environment is clean, well-lit, and free of dust. • Antec chassis feature rounded edges that minimize the occurrence of hand injuries. Nonetheless, exercise caution and control when handling chassis interiors. We strongly recommend taki
Résumé du contenu de la page N° 8
SECTION 2 HARDWARE INSTALLATION 8
Résumé du contenu de la page N° 9
2.1 SETTING UP Begin by removing the left side panel by loosening the thumbscrews and swinging the panel outward, pulling it back towards you; this will completely remove it. Cut the ties on the 5.25” drive cage with a wire cutter and remove the plastic bag of screws. The SOLO II should now look like this. 9
Résumé du contenu de la page N° 10
2.2 MOTHERBOARD INSTALLATION Before proceeding: Check the manual for your CPU cooler to find out if there are steps you must do before installing the motherboard. Make sure you have the correct I/O panel for your motherboard. If the panel provided with the chassis isn’t suitable, please contact your motherboard manufacturer for the correct I/O panel. Make sure you have the correct I/O panel. The SOLO II comes with four preinstalled motherboard standoffs.
Résumé du contenu de la page N° 11
3. Screw your motherboard into the standoffs with the provided motherboard mounting screws. 2.3 INSTALLING THE KUHLER H O 2 The following instructs how to install the Antec KUHLER H O liquid CPU cooler (620 / 920). For any other 2 CPU coolers, please consult your manufacturer’s installation guide. Caution: - We strongly recommend installing the KUHLER H O only after installing the power supply (See Step 2.4). 2 PSU installation will be difficult ot
Résumé du contenu de la page N° 12
2. The TrueQuiet™ fan has two small black clips attached to the fan’s two-speed switch. With your thumb and forefinger, spread the clips while pushing from the rear of the case to remove the switch. 3. Preparing the KUHLER H O backplate is specific to your CPU socket. Please refer to the KUHLER 2 H O installation guide, available at 2 http://www.antec.com/Believe_it/product.php?id=Mjc2OCYxNw== (KUHLER H O 620) or 2 http://www.antec.com/Believe_it/product.php
Résumé du contenu de la page N° 13
2. Remove the second screw with your other hand supporting the beam so the beam won’t drop. 3. Repeat steps 1 and 2 for the support beam screws at the rear of the case. . 4. Place the SOLO II on its side. Position the PSU into the mount and secure it with the PSU screws provided. If your PSU has a fan on its top side, make sure it aligns with the SOLO II’s top intake vent. 5. Re-attach the PSU support beam. 13
Résumé du contenu de la page N° 14
2.5 CABLE MANAGEMENT There is a cable management area between the motherboard and right side panel as well as cable hooks located on the side of the 3.5” drive cage. You can tuck excess cables in this area or route them to the drive bays. Choose the cables you would like to pass through the holes behind the motherboard tray. Pull them through the hole toward the right side of the case. For cables which will be routed directly to front drives or other internal accessories, cable
Résumé du contenu de la page N° 15
2. Attach the drive rails to your 5.25” device. These rails have three depth settings that accommodate the depth of your 5.25” drive. 3. Make sure to properly align your drive rails with your 5.25” drive. We recommend attaching one rail with one of the 5.25” drive screws and closing the bezel as a trial. Use the four 5.25” drive screws to secure your drive. 4. Slide the 5.25” drive into the appropriate drive bay. You will know the drive is secure when you hear
Résumé du contenu de la page N° 16
2.7 INTERNAL 3.5” AND 2.5” INSTALLATION (TRAY MOUNTS AND SUSPENSION MOUNTING SYSTEM) The following text outlines the preparatory stages for installing 3.5” / 2.5” drives using drives trays and the suspension mounting system. 1. If you have reattached it, remove the left side panel. Loosen the side panel screws and swing the panel outward, pulling it back towards you; this will completely remove it. 2. Remove the front bezel by locating the bezel tabs and pulling them to release
Résumé du contenu de la page N° 17
3.5” drive 2.5” drive 5. Insert the 3.5” / 2.5” drive into the drive cage by pinching the ends of the drive tray and sliding the tray along the rails until the tray locks firmly into position. 3.5” drive 2.5” drive 6. Mount any other 3.5” / 2.5” devices accordingly. For Suspension Mounting Installation: The SOLO II accommodates two 3.5” drives using the suspension mounting system. Each hard drive needs two suspenders (front and rear) to mo
Résumé du contenu de la page N° 18
4. Twist the rear suspender and guide the hard drive through it. 5. Find the appropriate power connector on the PSU and connect it to the device. 6. Repeat the same procedure for a second drive if necessary. 7. Close and secure the drive cage door. 2.8 INTERNAL 2.5” DEVICE INSTALLATION Toward the bottom-right of the motherboard tray, you will see a mount for a 2.5” device. To install a 2.5” device: 1. Align the 2.5” drive with the mounting holes w
Résumé du contenu de la page N° 19
SECTION 3 FRONT I/O PORTS 19
Résumé du contenu de la page N° 20
3.1 USB 2.0 Connect the front I/O panel USB cable to the USB header pin on your motherboard. Check your motherboard user’s manual to ensure that it matches the table below: 1 2 Pin SignalNames Pin SignalNames 1 USBPower1 2 USBPower2 3 NegativeSignal1 4 NegativeSignal2 PositiveSignal1 6 PositiveSignal2 5 Ground1 8 Ground2 7 9 Key(NoConnection) 10 EmptyPin 9 10 3.2 USB 3.0 The SOLO II comes with two front panel USB 3.0 ports and includes an inter
