Instruction d'utilisation Garland H280

Instruction d'utilisation pour le dispositif Garland H280

Dispositif: Garland H280
Catégorie: Four
Fabricant: Garland
Dimension: 1.35 MB
Date d'addition: 3/29/2013
Nombre des pages: 23
Imprimez l'instruction

Téléchargez

Comment utiliser?

Notre objectif consiste à vous assurer le plus rapide accès au contenu de l'instruction d'utilisation du dispositif Garland H280. En utilisant l'aperçu en ligne vous pouvez parcourir le sommaire et passer à la page où vous trouverez la résolution de votre problème avec Garland H280.

Pour votre confort

Si regarder l'instruction Garland H280 directement sur la page n'est pas confortable pour vous, vous pouvez profiter de deux solutions possibles:

  • Exploration au mode de plein écran - pour analyser l'instruction d'une manière commode (sans l'avoir téléchargée sur votre ordinateur) vous pouvez utiliser le mode d'exploration en plein écran. Pour démarrer l'exploration de l'instruction Garland H280 en plein écran, utilisez le bouton Plein écran.
  • Téléchargement sur l'ordinateur - vous pouvez aussi télécharger l'instruction Garland H280 sur votre ordinateur et la sauvegarder dans vos ressources. Si vous n'avez pas envie de gaspiller votre espace disque, vous pouvez toujours télécharger cette instruction du ManualsBase dans l'avenir.
Garland H280 Manuel d'utilisation - Online PDF
Advertisement
« Page 1 of 23 »
Advertisement
Version imprimée

Beaucoup de gens préfèrent de lire les documents dans la version imprimée et non pas sur l'écran. L'option d'impression de l'instruction est aussi prévue et vous pouvez en profiter en cliquant le lien ci-dessus - Imprimez l'instruction. Il n'est pas nécessaire d'imprimer toute l'instruction Garland H280 - on peut choisir des pages. Economisez le papier.

Résumés

Vous trouverez ci-dessous les annonces des contenus qui se trouvent sur les pages suivantes de l'instruction de Garland H280. Si vous voulez parcourir rapidement le contenu des pages suivantes de l'instruction, vous pouvez en profiter.

Résumés du contenu
Résumé du contenu de la page N° 1



H280-series Valve Overheat / Relocation Kit Instructions: RC Ovens

Instructions for Applying Kit #4523368

This kit is for a convection RC, 36” oven only. For a Standard 36” oven, use Kit #4522559

Installation Prerequisites:
 RC Oven, Piezoelectric Ignition
 U-Burner with no welded bracket

Tools Needed:
 Wrenches
 Small Hacksaw (for extension installation if required)
 Screwdrivers (Robertson, Flat), long and short
 Riveter
 Electrical Tape

Parts:

Part # Descr

Résumé du contenu de la page N° 2

Instructions: 1) Remove Kick Plate  Unscrew and set aside  This kick plate will not be reinstalled. A replacement is provided in the kit. 2) Remove Safety Valve  The following steps will apply for a Baso Valve: 1) Unscrew 11/16” compression nut on oven orifice fitting. 2) Unscrew 11/16” compression nut on 11/16” elbow on Valve Main Burner Gas Inlet.  Elbow itself should still be connected to Main Gas Inlet but detached from valve. 3) Unscrew 7/16” compression nut on Pilot Ga

Résumé du contenu de la page N° 3

3) Unscrew Igniter Bracket  Unscrew the two screws holding down the igniter bracket to the orifice bracket. Left: Before removal, location of screws shown by arrows Right: After removal 4) Remove Door Springs  Once the springs are removed, the oven door will be free to fall. Use a strong tape to keep the oven door closed for safety purposes.  For the door hinge with no microswitch:  Insert a long screwdriver underneath the bell crank assembly such that the tip extends beh

Résumé du contenu de la page N° 4

 Pry upward with the screwdriver. While holding this position, unhook the oven door hinge link. Unhooked oven door hinge link  Use flat head screwdriver to pry spring from bell crank assembly. Remove spring. Prying spring from bell crank assembly 03/09/09 P/N 4523367 Page 4

Résumé du contenu de la page N° 5

 For the door hinge with a microswitch:  Unscrew the microswitch bracket from the oven frame. It is important that the microswitch be removed prior to removing the spring to prevent damage to the microswitch when the springs are reinstalled later. Microswitch bracket held to oven frame by two screws indicated by the arrows  Follow the same steps as before, using the screwdriver to pry the bell crank assembly upwards to unhook the oven door hinge link, then pry the spring loose

Résumé du contenu de la page N° 6

5) Remove Orifice Bracket  After removing the igniter bracket, the orifice bracket will be held in place by a single screw directly above the orifice. Note that with the removal of the igniter bracket, the orifice bracket is held down by a single screw as shown by the arrow 03/09/09 P/N 4523367 Page 6

Résumé du contenu de la page N° 7

6) Install Extension Fitting (if applicable)  If pilot gas tube going into the valve already has an extension piece (short piece of tubing plus 3/16” brass fitting), unscrew the shorter piece of tubing and proceed to Step 13. Otherwise, follow these steps to install the proper fitting.  This step must be performed if a TS-11 valve was just removed.  If a Baso valve was uninstalled, cut off 2.5” of the free end of the incoming pilot gas tube to remove the original ferrule and nut and

Résumé du contenu de la page N° 8

7) Remove Left and Right Front Shields  Both shields are attached to the upper support bar using 3 screws. Left: Left side front shield, location of screws shown by arrows Right: Right side front shield, location of screws shown by arrows 8) Remove Burner  Burner is not screwed down to oven floor and can be removed by gently sliding it out.  This burner will not be reinstalled. Left: Lower oven cavity after removal of front shields Right: Original burner with single w

Résumé du contenu de la page N° 9

9) Unscrew Pilot Bracket from Oven Floor  The bracket is held down to the oven floor using two screws. This bracket will not be reinstalled. Left: Pilot assembly with bracket mounted to oven floor Right: Pilot assembly with bracket removed 10) Detach Igniter and Bracket from Pilot Assembly  Use a pair of pliers to gently detach the ignition wire from the igniter.  Slide the sheath off the wire. This sheath will be reused in the next step.  The old pilot assembly (including

Résumé du contenu de la page N° 10

11) Assemble New Pilot Assembly  A colored line on the top of the pilot indicates the type of fuel used. A BLACK line is used on a natural gas pilot, whereas a RED line is used on a propane pilot. Ensure the proper pilot is used.  Insert sheath onto new pilot assembly ignition wire  Push sheath onto wire until about 1 inch of orange ignition wire protrudes from the free end New pilot assembly with sheath inserted onto ignition wire  Use electrical tape to secure the free en

Résumé du contenu de la page N° 11

 Reattach original igniter Connection of taped ignition wire end to original igniter  Attach flex tube to pilot assembly  Unscrew the nut on the end of the selected pilot to release the nut, the ferrule and the orifice. Install the nut and the ferrule on one end of the flex tube.  Place the orifice back into the pilot and screw on the flex tube. Nut on new pilot assembly unscrewed, revealing orifice and ferrule. 03/09/09 P/N 4523367 Page 11

Résumé du contenu de la page N° 12

 Attach new Robertshaw thermocouple to pilot assembly  Push the thermocouple all the way into its slot on the pilot. Left: Wrong installation. Thermocouple not pushed all the way through socket. Right: Correct installation. Thermocouple pushed all the way through socket. 12) Attach New Pilot Assembly to Welded Bracket on New Burner  The pilot mounts onto the welded bracket using a single screw  Bend the thermocouple and flex tube approximately as shown in the picture. This w

Résumé du contenu de la page N° 13

13) Install New Burner  Ensure that the bracket at the tip of the burner locks onto the bracket attached to the oven floor. No screws are necessary for this procedure.  The burner may not stand up perfectly by itself. The installation of the oven orifice later will correct this problem. New burner and pilot assembly installed 14) Reinstall Both Front Shields  Install the right side shield first, guiding the various pieces of tubing and wire as shown in the below photograph.

Résumé du contenu de la page N° 14

15) Reinstall Orifice Bracket  Refer to Step 5 for orifice bracket connections  Make sure that the orifice is inserted straight into the burner and not at an angle Orifice inserted straight into burner opening 03/09/09 P/N 4523367 Page 14

Résumé du contenu de la page N° 15

16) Reinstall Door Springs  Refer to Step 4 for door spring connections  For the door hinge with no microswitch:  Hook on one end of the spring to the hooks from the orifice bracket  Place a screwdriver underneath the opposite end of the spring and pry upward to hook that end onto the bell crank assembly. Left: Setup screwdriver at end of spring underneath hook on bell crank assembly Right: Screwdriver pried upward, locks spring into place  Pry the bell crank assembly upw

Résumé du contenu de la page N° 16

17) Reinstall Igniter Bracket Refer to Step 3 for igniter bracket connections 18) Attach Main Burner Gas Line Flex Tubes onto Valve  Two brass fittings (Part 7, Assembly Drawing) should already be installed on the Main Burner gas inlet and outlet on the Baso valve. Otherwise, they are included in the kit separately for service personnel assembly.  Unscrew the free end of each fitting to release the nut and ferrule. Install these on one end of each 7/16” flex tube (Part 2, Assembly

Résumé du contenu de la page N° 17

19) Screw on Pilot Gas Flex Tube, Adjust Main Burner Gas Fitting  Remove the brass nut and ferrule originally on the pilot gas outlet on the Baso valve (Part 5 and Part 6, Assembly Drawing). Install them onto the free end of the flex tube.  Screw the pilot gas flex tube onto the Baso valve pilot gas outlet. This step should be done first to minimize stress on the flex tube during later steps.  The fitting on the Main Burner Gas Inlet needs to be turned 180  from its original positio

Résumé du contenu de la page N° 18

20) Install New Pilot Gas Tube  If a new 3/16” fitting (Part 4, Assembly Drawing) was installed on the pilot gas tube (Part 3, Assembly Drawing), unscrew the nut on the free end of the fitting to release the nut and the ferrule. If a fitting was already installed on the pilot gas tube, unscrew one end of the unused 3/16” fitting to release the nut and ferrule  Unscrew the nut on the Baso valve pilot gas inlet to release the brass nut and the ferrule.  Install these nuts and ferrules

Résumé du contenu de la page N° 19

21) Connect Remaining Tubes and Thermocouple  The free end of each 7/16” flex tube from the valve should be fitted with a 7/16” nut (Part 10, Assembly Drawing) and 7/16” ferrule (Part 11, Assembly Drawing).  Connect the 7/16” flex tube and the thermocouple. Tighten all connections.  The final tube connections should be comparable to the picture below. Final Tube Configuration 22) Attach Lighting Instructions to Valve Bracket  The pilot lighting instructions are riveted on th

Résumé du contenu de la page N° 20

23) Attach Bracket to Oven For Standard Ovens:  Unscrew the two screws holding the orifice bracket to the lower oven frame.  Slip the bracket (Part 8, Assembly Drawing) underneath the valve assembly such that the taller face is flush up against the lower oven frame.  Position the screw holes on the bracket such that two of them line up with the holes used for the orifice bracket. The third hole on the far right of the bracket will line up with a hole on the lower oven frame.


Instructions pareilles
# Instruction d'utilisation Catégorie Téléchargez
1 Garland All Purpose Manuel d'utilisation Four 1
2 Garland C0836-324A Manuel d'utilisation Four 0
3 Garland C0836-424A Manuel d'utilisation Four 0
4 Garland C0836-436A Manuel d'utilisation Four 0
5 Garland Broiler Manuel d'utilisation Four 1
6 Garland CPO-ED-12H Manuel d'utilisation Four 0
7 Garland C2100M Manuel d'utilisation Four 0
8 Garland EC0-E-20 Manuel d'utilisation Four 0
9 Garland CPO-ED-24H Manuel d'utilisation Four 0
10 Garland CPO-ES-12H Manuel d'utilisation Four 0
11 Garland Cuisine Series Heavy Duty Broiler W/Adjustable Racks C0836-326A Manuel d'utilisation Four 0
12 Garland Cuisine Series Heavy Duty Broiler W/Adjustable Racks C836-336A Manuel d'utilisation Four 0
13 Garland Cuisine Series Heavy Duty Broiler W/Adjustable Racks C836-436A Manuel d'utilisation Four 0
14 Garland ECO-E10 Manuel d'utilisation Four 0
15 Garland ECO-G-10-M Manuel d'utilisation Four 0
16 Edelbrock 17008 Manuel d'utilisation Four 0
17 3Com Manuel d'utilisation Four 1
18 ADIC 5.4 Manuel d'utilisation Four 1
19 AEG BC3000001 Manuel d'utilisation Four 527
20 AEG B3101-5-M Manuel d'utilisation Four 328