Résumé du contenu de la page N° 1
Installation Instructions
®
Epicure Range
For Use with Models: ER36D, ER36D-C, ER48D, ER48D-C
THIS APPLIANCE HAS BEEN TESTED IN ACCORDANCE WITH THE LATEST EDITION OF
ANSI Z21.1 STANDARD FOR HOUSEHOLD GAS APPLIANCES.
Part No. 100843 Rev. R
Résumé du contenu de la page N° 2
Table of Contents Important Safety Instructions ..................................................1-3 Installation Instructions ..........................................................7-18 Customer Service Information ....................................................3 Preparing for Installation ..........................................................7-9 Planning the Installation ...........................................................4-6 Electrical Connection ..........................
Résumé du contenu de la page N° 3
Important Safety Instructions Important Information About Safety WARNING Instructions NEVER use this appliance as a space heater to heat or warm the room. Doing so may result in carbon monoxide poisoning The Important Safety Instructions and warnings in this manual and overheating of the appliance. are not meant to cover all possible conditions and situations that can occur. Use common sense and caution when installing, WARNING maintaining or operating this or any other appliance. NEVER
Résumé du contenu de la page N° 4
Important Safety Instructions To reduce the risk of fire, explosion, electric shock, serious injury or death when installing or using this appliance, follow basic safety precautions, including the following: WARNING • Read the accompanying use and care manual before operating this appliance. • Keep packaging materials away from children. Plastic sheets and bags can cause suffocation. • If you receive a damaged product, immediately contact your dealer or builder. Do not install or use a damage
Résumé du contenu de la page N° 5
Important Safety Instructions WARNING • Make sure that all the cooktop parts are dry before lighting a burner. • Turn the knobs to the “OFF” position prior to removing them from the valve stems. • The cooktop should never be operated without the knobs and trim rings in place. • For your safety, do not use the oven to cook without the convection filter(s) installed. When the filter is not installed, the spinning fan blades at the back of the oven are exposed. • Non-stick coatings, when heated
Résumé du contenu de la page N° 6
Planning the Installation WARNING Electrical Requirements - Canada IMPORTANT: Observe all governing codes and ordinances It is the owner’s responsibility to ensure that the required 4 wire during planning and installation. Contact your local building electrical outlet is installed by a licensed electrician as specified department for further information. below prior to range installation. The electrical outlet installation, including minimum supply wire size and grounding, must be in accord
Résumé du contenu de la page N° 7
Planning the Installation Product Dimensions All tolerances: ±1/16” (±1.6mm) Gas Regulator Access, Cover Removed GAS - ELECTRICAL ACCESS DIMENSIONS Model A B C D E* Range Electrical Access, 5 5/8” 18 3/8” 10 3/4” 13 11/16” 7/8” Cover Removed ER36D (142.9mm) (466.7mm) (273.0mm) (347.7mm) (22.2mm) 3 13/16” 18 11/16” 9 3/8” 13 3/4” 1 1/8” ER48D (96.8mm) (474.7mm) (238.1mm) (349.3mm) (28.6mm) Inlet Back of Range * The diameter on models equipped for use in Canada is ¼” (6.4mm) larger B than tho
Résumé du contenu de la page N° 8
Planning the Installation Gas and Electrical Service Cabinet Layout • The shaded area shown denotes the location of the gas • Carefully check the location where the range is to be inlet and the electrical junction box/receptacle. This is the installed. For best performance, the range should be placed recommended location. For replacement purposes, the away from drafts that may be caused by doors, windows and location of the existing utilities may be utilized provided they heating and air
Résumé du contenu de la page N° 9
Installation Instructions Preparing for Installation WARNING Do not connect the unit to gas or power before proceeding with WARNING the following sections. • If the gas or electric service provided does not meet the Level and Adjust the Range Height product specifications, do not proceed with the installation. Call the dealer, the gas supplier or a licensed electrician. 1. Adjust the height by turning the bottom part of each leg • Before installing the range, you must locate and secure the
Résumé du contenu de la page N° 10
Installation Instructions 4. To avoid scratches, place small scraps of thin cardboard on Installing an ERV Raised Vent (Optional) the rear of the side panels where the backguard will make Install the ERV raised vent before installing the range. See the contact. Place the backguard over the back of the range. ERV installation instructions, part no. 103106. Special attention should be given to the lower flange in front of the backguard, which must fit between the stainless steel IMPORTANT: T
Résumé du contenu de la page N° 11
Installation Instructions Installing a Backguard (Continued) Removing the Oven Door 5. Fasten the backguard and the stainless steel trim piece in WARNING place with the five (5) existing chrome plated screws. • Do not attempt to disengage the hinge catches with the 6. Secure the rear of the backguard to the back of the range door removed from the oven. The hinge springs could with the eight (8) existing hex screws. release causing personal injury. • Do not lift or carry the oven door by th
Résumé du contenu de la page N° 12
Installation Instructions Electrical Connection Refer to the range rating label (see page 3) for power WARNING requirements. • Wire the range only in compliance with local ordinances. There are four possible ways to wire the range: • Improper connection of the electrical wiring can cause an • 4 Wire Conduit electric shock hazard and damage the appliance. Dacor • 3 Wire Conduit (where local codes permit) is not responsible for damages resulting from improper installation. • 4 Wire Appliance
Résumé du contenu de la page N° 13
Installation Instructions L1 Terminal Neutral Terminal L2 Terminal Jumper Removed Grounding Screw Red Wire Green Wire White Wire Black Wire Conduit Strain Relief Nut Connecting 4 Wire Conduit to Range L1 Terminal Neutral Terminal Jumper Link L2 Terminal Black Wire Bare Wire White Wire Connections Red Wire Conduit Strain Relief Nut Loop and Spade Terminal Connections Connecting 3 Wire Conduit to Range - Where Local Code Permits
Résumé du contenu de la page N° 14
Installation Instructions Connection to Electrical Connection (continued) Junction Box power supply Connecting the Conduit to the House Electrical Junction Box WARNING Do not connect the green appliance wire to the neutral (white) supply wire unless local building codes permit. Wire Nut, NOTES: 4 Places • The power supply must be properly polarized. Reverse polarity will result in continuous sparking of the electrodes, even after flame ignition. • If there is any doubt as to whether the p
Résumé du contenu de la page N° 15
Installation Instructions Junction Box Connection to Separate No. 10 (minimum power supply copper grounding wire Fasten clamp tightly on pipe Wire Nut, 4 Places Connect to appliance (page 10) Junction Box - 4 Wire Connection with External Ground Meter No. 4 copper wire Metal Water Pipe Clamps Bare metal Insulated Pipe Jumper
Résumé du contenu de la page N° 16
Installation Instructions 5. Slide the end of the appliance cord into the strain relief from Electrical Connection (continued) the bottom of the box 6. Connect the white (neutral) wire to the neutral terminal in the Connecting an Appliance Wire to the box. Range - Where Local Code Permits 7. Connect the L1 wire to the L1 power supply terminal in the box. WARNING 8. Connect the L2 wire to the L2 power supply terminal in the Do not connect the green appliance wire to the neutral (white) box
Résumé du contenu de la page N° 17
Installation Instructions Gas Supply Connection WARNING • Make sure the gas supply valve is off and that the power Bare Wire to the range is turned off at the circuit breaker or fuse box Connections prior to connecting the gas line. • Do not apply excessive pressure when tightening gas connections and fittings. • Do not use Teflon tape or plumber’s putty on gas flex line connections. • For LP installations, the LP gas tank must have its own high pressure regulator. This is in addition to
Résumé du contenu de la page N° 18
Installation Instructions Final Installation Installing the Burner Knobs 1. Peel the protective coating off of the range, including the CAUTION door. Installing the range knobs in the wrong position may result 2. Adjust the legs to the desired height. in damage to the griddle included with the range. The knobs 3. Carefully slide the range into position in the cut-out. The rear for the center burners are marked with the maximum griddle anti-tip leg should engage the anti-tip bracket. settin
Résumé du contenu de la page N° 19
Installation Instructions Installing the Burner Components WARNING Never attempt to operate the cooktop section of the range with any of the burner rings, burner caps or grates removed. • Remove the burner rings, burner caps and grates from their Spill Tray shipping packages. • Install the burners as shown. The location, type and size of Crown Burner the burners varies with the range model number. • Gently set the grates on top of the spill tray. Put the legs of each grate inside the corre
Résumé du contenu de la page N° 20
Installation Instructions Verifying Proper Operation Installation Checklist Prior to operating the cooktop or oven, please read the WARNING accompanying use and care manual carefully. Important safety, service and warranty information is contained within the use and • To ensure a safe and proper installation, the following care manual. checklist should be completed by the installer to ensure that no part of the installation has been overlooked. 1. Before beginning the test procedure, ens
