Instruction d'utilisation Raypak RAYTHERM 0066B

Instruction d'utilisation pour le dispositif Raypak RAYTHERM 0066B

Dispositif: Raypak RAYTHERM 0066B
Catégorie: Bouilleur
Fabricant: Raypak
Dimension: 1.06 MB
Date d'addition: 11/18/2013
Nombre des pages: 40
Imprimez l'instruction

Téléchargez

Comment utiliser?

Notre objectif consiste à vous assurer le plus rapide accès au contenu de l'instruction d'utilisation du dispositif Raypak RAYTHERM 0066B. En utilisant l'aperçu en ligne vous pouvez parcourir le sommaire et passer à la page où vous trouverez la résolution de votre problème avec Raypak RAYTHERM 0066B.

Pour votre confort

Si regarder l'instruction Raypak RAYTHERM 0066B directement sur la page n'est pas confortable pour vous, vous pouvez profiter de deux solutions possibles:

  • Exploration au mode de plein écran - pour analyser l'instruction d'une manière commode (sans l'avoir téléchargée sur votre ordinateur) vous pouvez utiliser le mode d'exploration en plein écran. Pour démarrer l'exploration de l'instruction Raypak RAYTHERM 0066B en plein écran, utilisez le bouton Plein écran.
  • Téléchargement sur l'ordinateur - vous pouvez aussi télécharger l'instruction Raypak RAYTHERM 0066B sur votre ordinateur et la sauvegarder dans vos ressources. Si vous n'avez pas envie de gaspiller votre espace disque, vous pouvez toujours télécharger cette instruction du ManualsBase dans l'avenir.
Raypak RAYTHERM 0066B Manuel d'utilisation - Online PDF
Advertisement
« Page 1 of 40 »
Advertisement
Version imprimée

Beaucoup de gens préfèrent de lire les documents dans la version imprimée et non pas sur l'écran. L'option d'impression de l'instruction est aussi prévue et vous pouvez en profiter en cliquant le lien ci-dessus - Imprimez l'instruction. Il n'est pas nécessaire d'imprimer toute l'instruction Raypak RAYTHERM 0066B - on peut choisir des pages. Economisez le papier.

Résumés

Vous trouverez ci-dessous les annonces des contenus qui se trouvent sur les pages suivantes de l'instruction de Raypak RAYTHERM 0066B. Si vous voulez parcourir rapidement le contenu des pages suivantes de l'instruction, vous pouvez en profiter.

Résumés du contenu
Résumé du contenu de la page N° 1

INSTALLATION & OPERATING
INSTRUCTIONS
Raytherm™
Residential
Boilers
Models 0042B, 0066B, 0090B
0135B & 0180B – Type H
WARNING: If these instructions are not followed exactly, a fire or explosion may
result causing property damage, personal injury or death.
FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and
liquids or other combustible materials in the vicinity of this or any other appliance. To
do so may result in an explosion or fire.
WHAT TO DO IF YOU SMELL GAS:
• Do n

Résumé du contenu de la page N° 2

Rev. 29 reflects the following: Changes to: Note on Page 8, text on Page 10, Item 7 on Page 11, mounting instructions on Page 12 2

Résumé du contenu de la page N° 3

CONTENTS WARNINGS 4 Heat Exchanger Re-assembly 33 Pay Attention to These Terms 4 Combustion Chamber Removal 33 RECEIVING EQUIPMENT 5 TROUBLESHOOTING 34 GENERAL SPECIFICATIONS 5 Adjustment & Replacement of INSTALLATION 7 Components 36 Code Requirements 7 Replacement Parts 37 Mounting Base 7 WARRANTY 38 Clearance Requirements 7 Combustion/Ventilation Air 8 Venting Connections 9 Vent Damper Installation Location 11 VENT DAMPER WIRING DIAGRAM 14 Gas Supply Connections 15 Gas Pressure 15 Water Connec

Résumé du contenu de la page N° 4

WARNINGS Pay Attention to These Terms Indicates the presence of immediate hazards which will cause severe DANGER: personal injury, death or substantial property damage if ignored. Indicates the presence of hazards or unsafe practices which could cause WARNING: severe personal injury, death or substantial property damage if ignored. Indicates the presence of hazards or unsafe practices which could cause CAUTION: minor personal injury or product or property damage if ignored. Indicates special ins

Résumé du contenu de la page N° 5

RECEIVING EQUIPMENT GENERAL SPECIFICATIONS On receipt of your equipment, visually check for exter- nal damage to the carton. If the carton is damaged, it Raytherm hydronic boilers are design certified and is suggested that a note be made on the Bill of Lading tested under the requirements of the latest edition of when signing for the equipment. the American National Standard, ANSI Z21.13/CSA 4.9. Each boiler has been constructed and pressure Remove the boiler from the carton, and if it is dam- t

Résumé du contenu de la page N° 6

Piping Connections Heating Net K Model Input Capacity I=B=R A B C Vent No. MBH Water MBH Rating Dia. Gas NPT NPT H-0042 42 35 30 1 in. 1/2 in. 11 in. 5 3/4 in. 5 1/2 in. 4 in. H-0066 66 54 47 1 in. 1/2 in. 11 in. 5 3/4 in. 5 3/4 in. 5 in. H-0090 90 74 64 1 in. 1/2 in. 11 in. 5 3/4 in. 5 3/4 in. 5 in. H-0135 135 109 95 1 1/4 in. 1/2 in. 18 in. 6 1/4 in. 6 1/4 in. 6 in. H-0180 180 148 129 1 1/4 in. 1/2 in. 18 in. 6 1/4 in. 8 in. 7 in. Table A: Specifications 16 B 1 AUTOMATIC 4 K / VENT DAMPER 2 (

Résumé du contenu de la page N° 7

INSTALLATION Code Requirements Installation must be in accordance with local codes, or in the absence of local codes, with the latest editions of the National Fuel Gas Code, ANSI Z223.1, and the National Electrical Code, ANSI/NFPA 70. In Canada, installations must conform with the current CSA B149 and the Canadian Electrical Code Part 1 CSA C22.2 No.1. Where required by the authority having jurisdic- tion, the installation must conform to American Society of Mechanical Engineers Safety Code for

Résumé du contenu de la page N° 8

3. Except for carpeted flooring, boilers are certified One opening shall be within 12" of the top, and the for installation on combustible floors. other opening within 12" of the floor. If additional gas appliances are installed in the same space, the total 4. For un-insulated hot water pipes, maintain a 2" input of all gas appliances installed in the same space, clearance, or consult local authority having juris- must be considered in the calculation. Refer to the lat- diction. est edition of t

Résumé du contenu de la page N° 9

Location of the openings is the same as in the previ- The discharge opening must be a minimum of two (2) ous case - that is, within 12" of the top, and within 12" feet vertically from the roof surface and at least two (2) of the bottom of the enclosure. If horizontal ducts are feet higher than any part of the building within ten (10) used, the area must be doubled and the duct area feet. Vent stack shall be at least five (5) feet in vertical shall not be less than the area of the openings they h

Résumé du contenu de la page N° 10

WARNING: These boilers must not be connected Roof Pitch (X/12) H (Min. ft) into any portion of mechanical draft systems Flat to 6/12 1 operating under positive pressure. To do so may cause the flue products to be discharged into the 6/12 to 7/12 1.25 living space causing serious health injury. Over 7/12 to 8/12 1.5 Over 8/12 to 9/12 2 For connections to gas vents or chimneys, vent instal- lations shall be in accordance with the Venting of Over 9/12 to 10/12 2.5 Equipment section of the National

Résumé du contenu de la page N° 11

At the time of removal of an existing boiler, the follow- Vent Damper Installation ing steps shall be followed with each appliance Location remaining connected to the common venting system placed in operation, while the other appliances remain- The vent damper supplied with each boiler must be ing connected to the common venting system are not located in the vent so that it serves only the appliance in operation. for which it is intended. 1. Seal any unused openings in the common venting If impr

Résumé du contenu de la page N° 12

Mounting On vertical vents, the vent damper may be mounted with the actuator in any position. On horizontal vents, do not mount the actuator either directly above or directly below the vent pipe; mount the vent damper actuator to the side of the vent. The vent damper is set up for a continuous pilot sys- tem. If the vent damper is installed on a system with an Intermittent Pilot, the energy savings of the vent damper can be improved by plugging the hole in the vent damper blade using the knockou

Résumé du contenu de la page N° 13

NOTE: To place vent damper in the open position to 24 V AC allow burner operation: Turn the power off. Turn the damper blade to fully open position (arrow facing same direction as vent pipe). Turn power on. R TH 2. Turn the thermostat or controller up to call for heat 2 and check that the vent damper indicator points to 4 GV the open position, as shown in Fig. 11. SS 3 1 HL J ES 3. Turn the thermostat or controller down again and check that the vent damper position indicator SS R returns to the

Résumé du contenu de la page N° 14

VENT DAMPER 14

Résumé du contenu de la page N° 15

1/2 in. Pipe 3/4 in. Pipe 1 in. Pipe 1 1/4 in. Pipe Model No. Nat. Pro. Nat. Pro. Nat. Pro. Nat. Pro. 0042 125 350 500 0066 60 160 175 460 0090 30 80 125 300 400 0135 15 40 60 150 200 450 0180 20 35 90 115 300 425 Table H: Maximum Equivalent Pipe Length (Feet) Gas Supply Connections NOTE: Do not use teflon tape on gas line pipe thread. A flexible sealant suitable for use with Natural and Propane gases is recommended. The inlet gas connection of the boiler gas valve is 1/2". Provide an adequate g

Résumé du contenu de la page N° 16

shipped loose. The full open position is appropriate for Systems with multiple zones may require an addition- most systems, and ensures adequate flow through the al circulator. Consult manufacturer's data for valve boiler. pressure drops. When an indirect water heating sys- tem is used, it is recommended that a separate If system flow is inadequate, (indicated by excessive circulator be installed to meet the required flow and temperature drop through the system) the bypass pressure drop conditio

Résumé du contenu de la page N° 17

Piping Diagrams Air Vent Air Scoop Diaphragm Expansion Tank Feed Valve Pipe Pressure Relief Valve to Drain Cold Water Inlet Heating Units Fig. 15: Single-Zone Piping 12” Max. Air Scoop Diaphragm Expansion Tank Feed Valve Pipe Pressure Relief Valve to Drain Circulators Cold Water Inlet Heating Units Fig. 16: Multiple Zones with Circulators 17 Air Vent

Résumé du contenu de la page N° 18

The room thermostat should be installed in accor- Electrical Wiring dance with the manufacturer's instructions. The thermostat heat anticipator should be set at 1.0 The electrical power supply requirement for these boil- ampere (automatic ignition) and 0.60 ampere (stand- ers is 120 VAC, 60 Hz. Field wiring connections and ing pilot) for single- zone installations. For multi-zone electrical grounding must comply with the local codes, applications, the heat anticipator setting should be or in the

Résumé du contenu de la page N° 19

Wiring Diagrams 19

Résumé du contenu de la page N° 20

20


Instructions pareilles
# Instruction d'utilisation Catégorie Téléchargez
1 Raypak 0090B 0135B Manuel d'utilisation Bouilleur 32
2 Raypak 1001 Manuel d'utilisation Bouilleur 17
3 Raypak 1000 .19C Manuel d'utilisation Bouilleur 1
4 Raypak 181-401 Manuel d'utilisation Bouilleur 5
5 Raypak 1501 Manuel d'utilisation Bouilleur 9
6 Raypak 0180B Type H Manuel d'utilisation Bouilleur 3
7 Raypak 133 Manuel d'utilisation Bouilleur 0
8 Raypak 180B Manuel d'utilisation Bouilleur 1
9 Raypak 2100-4001 Manuel d'utilisation Bouilleur 7
10 Raypak 240692 Manuel d'utilisation Bouilleur 0
11 Raypak 241275 Manuel d'utilisation Bouilleur 0
12 Raypak 182-400 Manuel d'utilisation Bouilleur 6
13 Raypak 2342BE Manuel d'utilisation Bouilleur 0
14 Raypak 1000 Manuel d'utilisation Bouilleur 0
15 Raypak 302BD-902BD Manuel d'utilisation Bouilleur 0
16 Sony HDV 1080I HVR-M15N/M15P Manuel d'utilisation Bouilleur 67
17 Sony HDV 1080I HVR-M25N/M25P Manuel d'utilisation Bouilleur 50
18 A.O. Smith 200 Manuel d'utilisation Bouilleur 2
19 A.O. Smith 201 Manuel d'utilisation Bouilleur 7
20 A.O. Smith 750 & 1000 Manuel d'utilisation Bouilleur 6