Résumé du contenu de la page N° 1
P-334WT
802.11g Wireless Broadband Router with Firewall
Quick Start Guide
September 2004
Version 3.60
Résumé du contenu de la page N° 2
P-334WT 1 Introducing the Prestige The Prestige is a broadband sharing gateway with a built-in wireless LAN access point and four-port 10/100 Mbps switch that makes it easy for people to set up a small home/office network and share Internet access via a broadband (cable/DSL) modem. Key features of the Prestige include media bandwidth management, an embedded 802.11g wireless LAN security, One-Touch Intelligent Security Technology, firewall, VPN, content filtering, NAT and UPnP. See your Use
Résumé du contenu de la page N° 3
P-334WT 2 Hardware Installation 2.1 Rear Panel LABEL DESCRIPTION LAN 10/100M Use an Ethernet cable to connect at least one computer for initial Prestige configuration. These ports are auto-negotiating (can connect at 10 or 100Mbps) and auto-sensing (automatically adjust to the type of Ethernet cable you use (straight-through or crossover)). WAN 10/100M Connect your cable/DSL modem to this port with the cable that came with your modem. POWER 12 VAC Connect the end of the included power
Résumé du contenu de la page N° 4
P-334WT 2.2 Front Panel LEDs The PWR LED blinks while performing system testing and then stays on if the testing is successful. The LAN, and WAN LEDs turn on if they are properly connected. LED STATUS COLOR DESCRIPTION PWR Off The Prestige is not receiving power. Amber On Power to the Prestige is too low Green On The Prestige is receiving power. Blinking The Prestige is performing testing. LAN 1- 4 Off The LAN is not connected. Green On The Prestige has a successful 10Mb Ethernet
Résumé du contenu de la page N° 5
P-334WT LED STATUS COLOR DESCRIPTION Blinking The Prestige is sending/receiving data WAN Off The WAN connection is not ready, or has failed. Green On The Prestige has a successful 10Mb WAN connection. Blinking The Prestige is sending/receiving data Amber On The Prestige has a successful 100Mb Ethernet connection. Blinking The Prestige is sending/receiving data WLAN Off The WLAN connection is not ready, or has failed. Green On The Prestige has a successful WLAN connection. Blinkin
Résumé du contenu de la page N° 6
P-334WT 2. In the Control Panel, double-click Network 3. Right-click Local Area Connection and then Properties. Connections (Network and Dial-up Connections in Windows 2000/NT). Control Panel Network Connection 6
Résumé du contenu de la page N° 7
P-334WT 4. Select Internet Protocol (TCP/IP) and then click 5. Select Use the following IP Address and fill in an Properties. IP address (between 192.168.1.3 and 192.168.1.254). 6. Type 255.255.255.0 as the Subnet mask. 1 7. Click Advanced. Local Area Connection Properties Internet Protocol Properties 8. Remove any previously installed gateways in the IP Settings tab and click OK to go back to the Internet Protocol TCP/IP Properties screen.
Résumé du contenu de la page N° 8
P-334WT No gateways configured. Advanced TCP/IP Settings 9. Click OK to close the Internet Protocol (TCP/IP) Properties window. 10. Click Close (OK in Windows 2000/NT) to close the Local Area Connection Properties window. 11. Close the Network Connections window (Network and Dial-up Connections in Windows 2000/NT). 3.2 Checking/Updating Your Computer’s IP Address 1. In the computer, click Start, (All) Programs, Accessories and then Command Prompt. 2
Résumé du contenu de la page N° 9
P-334WT 3. Press ENTER. The following screen displays. C:\>ping 192.168.1.1 Pinging 192.168.1.1 with 32 bytes of data: Reply from 192.168.1.1: bytes=32 time=10ms TTL=254 Reply from 192.168.1.1: bytes=32 time<10ms TTL=254 Reply from 192.168.1.1: bytes=32 time<10ms TTL=254 Reply from 192.168.1.1: bytes=32 time<10ms TTL=254 Ping statistics for 192.168.1.1: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum
Résumé du contenu de la page N° 10
P-334WT Default password. 3. It is highly recommended you change the default password! Enter a new password, retype it to confirm and click Apply; alternatively click Ignore to proceed to the main menu if you do not want to change the password now. If you do not change the password, the following screen appears every time you log in. Change default password. 4. You should now see the web configurator MAIN MENU screen. Click WIZARD to begin a series of screens to help you configure
Résumé du contenu de la page N° 11
P-334WT Click MAINTENANCE in the navigation panel to see Prestige performance statistics, upload firmware and back up, restore or upload a configuration file. Click LOGOUT when you have finished a Prestige management session. The Prestige automatically logs you out if it is left idle for five minutes; press ENTER to display the Login screen again and then log back in. This idle timeout timer is one of the many Prestige features that you may edit using the web configurator. WIZARD
Résumé du contenu de la page N° 12
P-334WT System Name is a unique name to identify the Prestige in an Ethernet network. Enter a descriptive name. The Domain Name entry is what is propagated to the DHCP clients on the LAN. If you leave this blank, the domain name obtained by DHCP from the ISP is used. Click Next to continue. 2. Use the second wizard screen to set up the wireless LAN. Name(SSID) is a unique name to identify the Prestige in the wireless LAN. Enter a descriptive name. The range of rad
Résumé du contenu de la page N° 13
P-334WT WEP (Wired Equivalent Privacy) encrypts data frames before transmitting over the wireless network. The higher the WEP Encryption, the higher the security but the slower the throughput. Use Passphrase to Select 64-bit, 128-bit or 256-bit from the automatically generate WEP Encryption drop-down list. a key or manually enter Select one of the Key radio buttons to a key in one of the Key use as the WEP key. 1~ 4 fields. You can generate or manually enter a WEP key by eith
Résumé du contenu de la page N° 14
P-334WT Choose Ethernet when the WAN port is used as a regular Ethernet. Choose from Standard, Telia Login or a RoadRunner version. You’ll need User Name, Password and Login Server IP Address for some Roadrunner versions. PPPoE or Point-to-Point Protocol over Ethernet (PPP over Ethernet) also functions as a dial-up connection. Therefore you’ll also need a username and password and possibly the PPPoE service name. Your ISP will give you all needed information. Choose PPTP if y
Résumé du contenu de la page N° 15
P-334WT WAN IP Address Assignment Select Get automatically from ISP if your ISP did not assign you a fixed IP address. Select Use fixed IP address to give the Prestige a fixed, unique IP address. The fixed IP address should be in the same subnet as your broadband modem or router. Enter a Subnet Mask appropriate to your network and the Gateway IP Address of the neighboring device, if you know it. If you do not, leave the Gateway IP Address field as 0.0.0.0. DNS Server Address
Résumé du contenu de la page N° 16
P-334WT OTIST Security You can assign the Prestige wireless security settings (SSID and either the WEP or WPA-PSK) to a ZyXEL wireless client that also supports OTIST. You must enable OTIST on the wireless client to have the Prestige’s wireless security settings assigned to it. Select the Yes radio button and click the Finish button to proceed with OTIST and complete the wizard setup. See the User’s Guide for more information on OTIST. 8. Confirm Your Settings If you hav
Résumé du contenu de la page N° 17
P-334WT Select the Active check box to have the Prestige apply bandwidth management to traffic going out through the Prestige's WAN, LAN or WLAN port. Enter the amount of Managed Bandwidth in kbps (2 to 100,000) that you want to allocate for traffic. 20 kbps to 20,000 kbps is recommended. The recommendation is to set this speed to be equal to or less than the speed of the broadband device connected to the WAN port. For example, set the speed to 1000 Kbps (or less) if the br
Résumé du contenu de la page N° 18
P-334WT Select High, Mid or Low priority for each service to have your Prestige limit the bandwidth used by bandwidth-hungry applications (or individuals) by allocating the maximum bandwidth for WAN, LAN and WLAN traffic. If the rules set up in this wizard are changed in the advanced setup, then the service priority will be set to Other. The Advanced Media Bandwidth Management configuration screens allow you to edit set class configurations and edit these rules. Click Finish to s
Résumé du contenu de la page N° 19
P-334WT PROBLEM CORRECTIVE ACTION Prestige from the LAN. Rear Panel section for details. Ping the Prestige from a LAN computer. Make sure your computer Ethernet card is installed and functioning properly. Cannot ping any If the 10/100M LAN LEDs are off, check the cable connections between the Prestige and computer on the LAN. your LAN computers. Verify that the IP address and subnet mask of the Prestige and the LAN computers are in the same IP address range. Cannot get a WAN IP The WAN
