Instruction d'utilisation Xantech RT16-10

Résumé du contenu de la page N° 1

Remote Control Switchers
INSTALLATION INSTRUCTIONS
RT16-10
ADDRESSABLE INFRARED ROUTER
The RT16-10 is a ONE-IN/SIXTEEN-OUT IR switcher which directs an infrared control signal to any one
of 16 output ports, any combination of ports, or all 16 as a group. You can control large groups of TV
monitors (or any other A/V product) from control locations using Xantech IR Receivers or Smart Pads. Up
to 16 devices may be addressed with one RT16-10. Additional RT-10's can be connected for control of
lar

Résumé du contenu de la page N° 2

RC68 PROGRAMMER / REMOTE CONTROL The RC68+ (or RC68) Programmer (available separately) contains all the commands necessary to operate the RT16-10 (see Fig. 3). • You will need it to program universal learning devices such as the Xantech URC-1 learning remote, the Xantech Smart Pads, the 590 Programmable Controller, the 710 Fone Link, etc., with commands that operate the RT16-10. • NOTE: The RC68+ codes operate several other Xantech models as well, such as the RS41AV, CC12, ZPR68, etc. Therefor

Résumé du contenu de la page N° 3

Remote Control Switchers 2. Multiple Routing IR routes can be established to any desired combination of ports (1 Controller & through 16) for simultaneous operation. This is useful if you wish to 1 Address ON (1) ON Switches address smaller groups of units for special purposes. Simply press 1 2 3 4 5 6 any desired combination of IR routes that you want (e.g., 2, 4, 5, 8, OFF (0) 11 & 16). ID CODE SWITCH Set #1 to ON (1) The chosen IR routes remain on, allowing C you to control just the selecte

Résumé du contenu de la page N° 4

INSTALLATION Fig. 5 illustrates a typical application where an RT16-10 is used to route IR control signals to 15 TV monitors. 1. For this example, it is assumed that Single Routing with Group ON and OFF is required. 2. Since only one RT16-10 is used in the system, the factory preset Code Group 70 can be used. The RC68+ Programmer is set to the same number. 3. The RC68+ commands 1 through 15 (see Fig. 3) will establish an IR route to each TV individually. The Group On command will route to all

Résumé du contenu de la page N° 5

Remote Control Switchers 780-10 J-BOX RECEIVER TV MONITOR #15 283M TV MONITOR #14 To Emitters 283M TV on even MONITOR #13 numbered 283M TV's TV MONITOR #12 283M TV MONITOR #11 283M TV MONITOR #10 283M TV MONITOR #9 283M Smart Pad™ TV MONITOR #8 White Use additional Striped 283M TV Control Devices Side (+) MONITOR as needed. #7 283M TV 780-10 MONITOR #6 J-Box IR Receiver 283M TV MONITOR #5 +12 VDC +12V IR OUT IR OUT 283-00 GND GND TV MONITOR White Striped Side (+) #4 Smart Pad™ 283M TV MONITOR #3

Résumé du contenu de la page N° 6

CPL10 RF RF/IR IR CPL10 RF RF/IR IR CPL10 RF RF/IR IN OUT IR CPL10 RF RF/IR IR CPL10 RF RF/IR IR CPL10 RF RF/IR IR CPL10 RF RF/IR IR CPL10 RF RF/IR IR RF SIGNAL Source Control TV/Video TV/Video Emitters IR SIGNAL Source Source (if Needed) 2512 2-way Combiner DA500 To CPL10 RF AMP Couplers for 202-00 4-way remaining 7 RF Splitters TV's (5 locations) To 7 TV's (duplicate of MODEL RT16-10 splitter and ADDRESSABLE IR ROUTER Coaxial coupler Cables system to left) 6015900 3.5mm mono mini plug to strip