Résumé du contenu de la page N° 1
1
User’s Guide
Résumé du contenu de la page N° 2
Copyright Statement No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, whether electronic, mechanical, photocopying, recording, or otherwise without the prior writing of the publisher. JUL. 2004 2 User’s Guide
Résumé du contenu de la page N° 3
Contents 1. Introduction ...............................................................................................
Résumé du contenu de la page N° 4
1. Introduction Thank you for purchasing TRENDnet’s Wireless 802.11g Outdoor AP Bridge. This user guide will assist you with the installation procedure. The package you have received should contain the following items: For TEW-412APBO TEW-412APBO User’s Guide CD-ROM Quick Installation Guide POE Host & Power Cord Mounting Kit Cat.5 Ethernet Cable (1.5m/5ft.) For TEW-413APBO TEW-412APBO User’s Guide CD-ROM Quick Installation Guide POE Host & Power Cord N-t
Résumé du contenu de la page N° 5
2. Safety Notification This device should be professionally installed; the installer shall be responsible for ensuring tha
Résumé du contenu de la page N° 6
3. AP Default Settings The default settings are shown following. User admin Password admin AP IP Address 192.168.1.250 AP Subnet Mask 255.255.255.0 RF ESSID ap11g 11g RF Channel 6 Mode 11b+g Encryption Disabled 6 User’s Guide
Résumé du contenu de la page N° 7
4. Web Management Settings TURN ON POWER SUPPLY Quick power cycle can caused system corruption. When power on, be ca
Résumé du contenu de la page N° 8
4.1. Primary Setup MAKE CORRECT NETWORK SETTINGS OF YOUR COMPUTER To change the configuration, use Internet Explorer (IE) or Netscape Communicator to connect the WEB management 192.168.1.250. Primary Setup This screen contains all of the AP's basic setup functions. . Most users will be able to configure the AP and get it working properly using the settings on this screen. LAN IP Address and Subnet Mask: This is the AP's IP Address and Subnet Mask as seen on the i
Résumé du contenu de la page N° 9
Wireless Settings SSID: The service set identifier ( SSID ) or network name. It is case sensitive and must not excee
Résumé du contenu de la page N° 10
Important Notice In order to make right use of WPA, please ensure that your current Wireless Adapter’s driver, and Wireless Utility can support it, WPA needs 802.1x authentication (when RADIUS mode is chosen), though the Operating System must also support 802.1x protocol. For Microsoft’s OS family, only Windows XP has inc orporated this by default. The rest of the OS must installed 3er party’s client software such as Funk ODySSey. -WPA-Preshared key There are two encryption
Résumé du contenu de la page N° 11
-WPA RADIUS WPA RADIUS uses an external RADIUS server to perform user authentication. To use WPA RADIUS, enter the IP
Résumé du contenu de la page N° 12
4.2. System AP Password: Changing the password for the AP is as easy as typing the password into the Enter New Password field. Then, type it again into the Re-enter to confirm. * Click the Apply button to save the setting. Use the default password when you first open the configuration pages, after you have configured these settings, you should set a new password for the AP (using the Password screen). This will increase security, protecting the AP from unauthorized changes.
Résumé du contenu de la page N° 13
4.3. Operating Mode Access Point: This mode provides access for wireless stations to wired LANs and from wired LANs
Résumé du contenu de la page N° 14
Important Both units must be selected as AP Repeater mode in order to establish the Wireless link communication. The remote AP MAC address to be filled at this selection should be the LAN MAC address that is displaying at the Operating Mode’s web pages AP Repeater: This mode allows the AP to keep the AP function role and at the same time performing a communication with other 802.11g AP to establish and extend your Wireless Network cover. Please enter the Remote Access Point’s
Résumé du contenu de la page N° 15
4.4. Status This screen displays the IEEE 802.11g AP's current status and settings. This information is read-only. Th
Résumé du contenu de la page N° 16
4.5 Traffic Log Traffic Log: The AP can keep logs of all incoming or outgoing traffic for your network traffic. This feature is disabled by default. To keep activity logs, select Enable. To keep a permanent record of activity logs as a file on your PC’s hard drive, Log viewer software must be used. In the Send Log to field, enter the fixed IP address of the PC running the Log viewer software. The AP will send updated logs to that PC. To see a temporary log of the AP’s most recent
Résumé du contenu de la page N° 17
4.6 Access Control Access Control: This function will allow administrator to have access control by enter MAC address
Résumé du contenu de la page N° 18
4.7 Advanced Wireless Authentication Type: Auto: Auto is the default authentication algorithm. It will change its authentication type automatically to fulfill client’s requirement. Open System: Open System authentication is not required to be successful while a client may decline to authenticate with any particular other client. Shared Key: Shared Key is only available if the WEP option is implemented. Shared Key authentication supports authentication of clients as either a member
Résumé du contenu de la page N° 19
RTS Threshold: This value should remain at its default setting of 2346. Should you encounter inconsistent data flow, only
Résumé du contenu de la page N° 20
4.8. SNMP INFO SNMP INFO: The SNMP screen allows you to customize the Simple Network Management Protocol (SNMP) settings. SNMP is a popular network monitoring and management protocol. SNMPv2c To enable the SNMP support feature, select Enable. Otherwise, select Disable. Identification Contact In the contact field, enter contact information for the AP. Unit Name In the Unit Name and description field, and enter the name of the AP or AP description description. Physical In the Phy
