Résumé du contenu de la page N° 1
TL-WR702N
150Mbps Wireless N Nano Router
Rev: 1.0.0
1910010547
Résumé du contenu de la page N° 2
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2011 TP-LINK TECHNOLOGIES CO.,
Résumé du contenu de la page N° 3
FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. “To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all per
Résumé du contenu de la page N° 4
TP-LINK TECHNOLOGIES CO., LTD DECLARATION OF CONFORMITY For the following equipment: Product Description: 150Mbps Wireless N Nano Router Model No.: TL-WR702N Trademark: TP-LINK We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives: Directives 1999/5/EC The above product is in conformity with the following standards or other normative documents ETSI EN 300 328 V1.7.1: 20
Résumé du contenu de la page N° 5
CONTENTS Package Contents..................................................................................................................................1 Chapter 1. Introduction.......................................................................................................................2 1.1 Overview of the Router .......................................................................................................2 1.2 Conventions .............................................
Résumé du contenu de la page N° 6
5.12 IP & MAC Binding Setting ................................................................................................ 94 5.13 Dynamic DNS................................................................................................................... 96 5.14 System Tools.................................................................................................................... 98 Chapter 6. Configuration for Repeater Mode ..................................................
Résumé du contenu de la page N° 7
TL-WR702N 150Mbps Wireless N Nano Router Package Contents The following items should be found in your package: One TL-WR702N 150Mbps Wireless N Nano Router Quick Installation Guide One Power Adapter One USB Cable One RJ-45 Ethernet Cable One Resource CD for TL-WR702N 150Mbps Wireless N Nano Router, including: • User Guide • Other Helpful Information Note: Make sure that the package contains the above items. If any of the listed items is damaged or missing, please contact
Résumé du contenu de la page N° 8
TL-WR702N 150Mbps Wireless N Nano Router Chapter 1. Introduction Thank you for choosing the TL-WR702N 150Mbps Wireless N Nano Router. 1.1 Overview of the Router Small enough to fit in the average pocket, the TL-WR702N 150Mbps Wireless N Nano Router is uniquely suited to provide robust wireless networking to travelers, students, or anyone else for work or play. Incredible Speed TL-WR702N supports the newest 802.11n standards, and provides backward compatibility with older 802.11b/g s
Résumé du contenu de la page N° 9
TL-WR702N 150Mbps Wireless N Nano Router this user guide. Before installing the Router, please look through this guide to know all the Router’s functions. 1.2 Conventions The Router or TL-WR702N mentioned in this guide stands for TL-WR702N 150Mbps Wireless N Nano Router without any explanation. Parameters provided in the pictures are just references for setting up the product, which may differ from the actual situation. You can set the parameters according to your demand. 1.3 Main Feat
Résumé du contenu de la page N° 10
TL-WR702N 150Mbps Wireless N Nano Router 1.4 Panel Layout Figure 1-1 TL-WR702N sketch LED Status Indication Solid It’s powered on but the LAN/WAN port is not connected. Flashing The LAN/WAN cable is connected but there is no data Slowly being transmitted or received. Flashing The LAN/WAN cable is connected and there is data being Quickly transmitted or received. Table 1-1 The LED Description LAN/WAN: This LAN/WAN port works as LAN in AP/Repeater/ Bridge/Client mode and as WAN
Résumé du contenu de la page N° 11
TL-WR702N 150Mbps Wireless N Nano Router Chapter 2. Connecting the Router 2.1 System Requirements Each PC in the LAN needs a working Ethernet Adapter TCP/IP protocol must be installed on each PC Web browser, such as Microsoft Internet Explorer 5.0 or later, Mozilla Firefox, Apple Safari If the device is configured to AP router mode, you also need Broadband Internet Access Service (DSL/Cable/Ethernet) One DSL/Cable Modem that has an RJ45 connector (which is not necessary if the Rout
Résumé du contenu de la page N° 12
TL-WR702N 150Mbps Wireless N Nano Router 2.3.1 AP Mode As the supplement of wired LAN, TL-WR702N enables the wired LAN to connect to the Internet wirelessly. The default mode of TL-WR702N is AP. Plug the power plug of TL-WR702N in electrical wall socket and connect the Ethernet cable correctly, you can surf the Internet by connecting your PC(s) to the Router wirelessly. On this mode, the only wired port works as LAN. Computer could connect to the device by either wired or wireless way.
Résumé du contenu de la page N° 13
TL-WR702N 150Mbps Wireless N Nano Router Figure 2-2 Hardware Installation of the TL-WR702N in Router Mode 1. Connect the WAN port of TL-WR702N to the LAN Port on the DSL/Cable Modem. 2. Connect the WAN port on the DSL/Cable Modem to the wired Internet. 3. Plug the power plug of TL-WR702N in electrical wall socket. 4. Power on the DSL/Cable Modem, PC(s) and notebook(s). 2.3.3 Repeater Mode TL-WR702N is used to extend the range of wireless signal of the existing AP or wireless router. O
Résumé du contenu de la page N° 14
TL-WR702N 150Mbps Wireless N Nano Router Note: It is recommended that you connect a PC/notebook to the LAN port of the Router with an Ethernet cable, and then login the Router from the PC/notebook to set the Router in AP Repeater mode. 2.3.4 Bridge Mode Similar to the Bridge mode, TL-WR702N in Bridge mode is also used to extend the range of wireless signal of the existing AP or wireless router. On this mode, the only wired port works as LAN. Computer could connect to the device by eit
Résumé du contenu de la page N° 15
TL-WR702N 150Mbps Wireless N Nano Router Figure 2-5 Hardware Installation of the TL-WR702N in Client Mode 1. Connect the PC to the LAN/WAN port of TL-WR702N router with an Ethernet cable. 2. Plug the power plug of TL-WR702N in electrical wall socket. 3. Power on the PC(s). Note: TL-WR702N can be powered by external power adapter or USB connection to computer. - 9 -
Résumé du contenu de la page N° 16
TL-WR702N 150Mbps Wireless N Nano Router Chapter 3. Quick Installation Guide This chapter will show you how to configure the basic functions of your TL-WR702N 150Mbps Wireless N Nano Router using Quick Setup Wizard within minutes. 3.1 TCP/IP Configuration The default IP address of the TL-WR702N 150Mbps Wireless N Nano Router is 192.168.0.254. And the default Subnet Mask is 255.255.255.0. These values can be changed as you desire. In this guide, we use all the default values for descripti
Résumé du contenu de la page N° 17
TL-WR702N 150Mbps Wireless N Nano Router Figure 3-1 Success result of Ping command If the result displayed is similar to the Figure 3-2, it means the connection between your PC and the Router has failed. Figure 3-2 Failure result of Ping command Please check the connection following these steps: 1. Is the connection between your PC and the Router correct? Note: The LED of LAN/WAN ports which you link to on the Router should be lit. 2. Is the TCP/IP configuration for your PC
Résumé du contenu de la page N° 18
TL-WR702N 150Mbps Wireless N Nano Router 3.2 Quick Installation Guide With a Web-based utility, it is easy to configure and manage the TL-WR702N 150Mbps Wireless N Nano Router. The Web-based utility can be used on any Windows, Macintosh or UNIX OS with a Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari. 1. To access the configuration utility, open a web-browser and type in the default address http://192.168.0.254 in the address field of the browser. After
Résumé du contenu de la page N° 19
TL-WR702N 150Mbps Wireless N Nano Router 3. Click Next, and then Working Mode page will appear, shown in Figure 3-5. Figure 3-5 Quick Setup - Working Mode Note: The Router supports five working modes for multi-user to access the Internet: AP, Router, Repeater, Bridge and Client. In AP mode, TL-WR702N enables the wired LAN to connect to the Internet wirelessly. In Router mode, it can access the Internet via DSL/Cable Modem. In Repeater mode, the device will relay data to an associated
Résumé du contenu de la page N° 20
TL-WR702N 150Mbps Wireless N Nano Router Figure 3-6 Quick Setup - Wireless AP Wireless Radio - Enable or disable the wireless radio choosing from the pull-down list. SSID - Enter a string of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network. The default SSID is set to be TP-LINK_XXXXXX (XXXXXX indicates the last unique six numbers of each Router’s MAC address). But it is recommended strongly that you chang
