Résumé du contenu de la page N° 1
LevelOne
WBR-3402TX
1W,4L 11g Wireless ADSL Router
w/VPN/Printer Server(USB)
User`s Manual
1
Résumé du contenu de la page N° 2
Table of Contents Chapter 1 Introduction ..................................................................................................... 4 Functions and Features .............................................................................................. 4 Packing List ............................................................................................................... 6 Chapter 2 Hardware Installation.....................................................................
Résumé du contenu de la page N° 3
4.8.6 Miscellaneous Items ....................................................................................... 75 Chapter 5 Print Server.................................................................................................... 76 5.1 Configuring on Windows 95/98 Platforms ........................................................ 76 5.2 Configuring on Windows NT Platforms ............................................................ 79 5.3 Configuring on Windows 2000 and XP Platfo
Résumé du contenu de la page N° 4
Chapter 1 Introduction Chapter 1 Introduction Chapter 1 Introduction Congratulations on your purchase of LevelOne WBR-3402 ADSL Wireless Broadband Router. This product is specifically designed for Small Office and Home Office needs. It provides a complete SOHO solution for Internet surfing, and is easy to configure and operate even for non-technical users. Instructions for installing and configuring this product can be found in this manual. Before you install and use this product, pl
Résumé du contenu de la page N° 5
correctly. Statistics of WAN Supported Enables you to monitor inbound and outbound packets Wireless functions High speed for wireless LAN connection Up to 54Mbps data rate by incorporating Orthogonal Frequency Division Multiplexing (OFDM). Roaming Provides seamless roaming within the IEEE 802.11b(11M) and IEEE 802.11g(54M) WLAN infrastructure. IEEE 802.11b compatible (11M) Allowing inter-operation among multiple vendors. IEEE 802.11g compatible (54M) Allowing inter-operatio
Résumé du contenu de la page N° 6
When SPI Mode is enabled, the router will check every incoming packet to detect if this packet is valid. DoS Attack Detection Supported When this feature is enabled, the router will detect and log the DoS attack comes from the Internet. Advanced functions System time Supported Allow you to synchronize system time with network time server. E-mail Alert Supported The router can send its info by mail. Dynamic dns Supported At present,the router has 3 ddns.dyndns,TZO.com and dhs.
Résumé du contenu de la page N° 7
Chapter 2 Hardware Installation Chapter 2 Hardware Installation Chapter 2 Hardware Installation 2.1 Panel Layout 2.1.1. Front Panel Figure 2-1 Front Panel LED: LED Function Color Status Description Power is being applied to this POWER Power indicationGreen On product. This product is functioning STATUS System status Green Blinking properly. On The ADSL is linked. Show-tme ADSL status1 Green This router is trying to connect to Blinking your ISP The ADSL is sending or
Résumé du contenu de la page N° 8
2.1.2. Rear Panel Figure 2-2 Rear Panel Ports: Port Description 5VDC Power inlet: DC 5V, 2A ADSL the port where you will connect your phone jack.. Port 1-4 the ports where you will connect networked computers and other devices. USB USB Ports for USB printer. 2.2 Procedure for Hardware Installation 1. Decide where to place your WBR-3402, Wireless ADSL Router You can place your ADSL Wireless Broadband Router on a desk or other flat surface, or you can mount it on
Résumé du contenu de la page N° 9
Figure 2-3 Setup of LAN and WAN connections for this product. 3. Setup ADSL connection Prepare a telephone cable for connecting this product to your ISP. Figure 2-3 illustrates the ADSL connection. 4. Connecting this product with your printer Use the printer cable to connect your printer to the USB printer port of this product. 5. Power on Connecting the power cord to power inlet and turning the power switch on, this product will automatically enter the self-test phase. When it is
Résumé du contenu de la page N° 10
Chapter 3 Network Settings and Software Installation Chapter 3 Network Settings and Software Installation Chapter 3 Network Settings and Software Installation To use WBR-3402 correctly, you have to properly configure the network settings of your computers and install the attached setup program into your MS Windows platform (Windows 95/98/NT/2000). 3.1 Make Correct Network Settings of Your Computer The default IP address of this product is 192.168.123.254, and the default subnet
Résumé du contenu de la page N° 11
3.2 Install the Software into Your Computers Skip this section if you do not want to use the print server function of this product. Notice: If you are using Windows 2000/XP, please refer to Chapter 5 Printer - 5.3 Configuring on Windows 2000 and XP Platforms. It is not necessary to setup any program and the print-server can work. Step 1: Insert the installation CD-ROM into the CD-ROM drive. The following window will be shown automatically. If it isn’t, please run “install.exe” on the
Résumé du contenu de la page N° 12
Step 3: Select the destination folder and click on the Next button. Then, the setup program will begin to install the programs into the destination folder .Step 4: When the following window is displayed, click on the Finish button. Select the item to restart the computer and then click the OK button to reboot your computer. Step 4: After rebooting your computer, the software installation procedure is finished. Now, you can configure the NAT Router (refer to Chapter 4) and setup the Prin
Résumé du contenu de la page N° 13
Chapter 4 Configuring ADSL Wireless Broadband Router Chapter 4 Configuring ADSL Wireless Broadband Router Chapter 4 Configuring ADSL Wireless Broadband Router This product provides Web based configuration scheme, that is, configuring by your Web browser, such as Netscape Communicator or Internet Explorer. This approach can be adopted in any MS Windows, Macintosh or UNIX based platforms. 13
Résumé du contenu de la page N° 14
4.1 Start-up and Log in Activate your browser, and disable the proxy or add the IP address of this product into the exceptions. Then, type this product’s IP address in the Location (for Netscape) or Address (for IE) field and press ENTER. For example: http://192.168.123.254. After the connection is established, you will see the web user interface of this product. There are two appearances of web user interface: for general users and for system administrator. To log in as an adminis
Résumé du contenu de la page N° 15
4.2 Status This option provides the function for observing this product’s working status: A. WAN Port Status. If the WAN port is assigned a dynamic IP, there may appear a “Renew” or “Release” button on the Sidenote column. You can click this button to renew or release IP manually. B. Printer Status. The possible kinds of printer status include “Ready”, “Not ready”, “Printing…”, and “Device error”. When a job is printing, there may appear a “Kill Job” button on the Sidenote column. Yo
Résumé du contenu de la page N° 16
4.3 Wizard Setup Wizard will guide you through a basic configuration procedure step by step. Press ”Next >” 16
Résumé du contenu de la page N° 17
Setup Wizard - Select WAN Type: For detail settings, please refer to 4.4.1 primary setup. 4.4 Basic Setting 17
Résumé du contenu de la page N° 18
4.4.1 Primary Setup – WAN Type Press “Change” 18
Résumé du contenu de la page N° 19
This page is primary to enable this product to work properly. The setting items and the web appearance depend on the WAN type. Choose correct WAN type before you start. 1. LAN IP Address: the local IP address of this device. The computers on your network must use the LAN IP address of your product as their Default Gateway. You can change it if necessary. 2. WAN Type: WAN connection type of your ISP. You can click Change button to choose a correct one from the following five options: A. E
Résumé du contenu de la page N° 20
4.4.1.1 Ethernet Over ATM (RFC 1483 Bridged) without NAT This WAN type disable the NAT, this device becomes a pure bridge between your LAN and WAN, all the clients in your LAN must have legal IPs. If you enable the NAT feature, you have to set the following WAN IP settings. WAN IP Address, WAN Subnet Mask, WAN Gateway, and Primary/Secondary DNS These settings are also specified by your ISP. VPI/VCI Numbers: The channel settings provided by your ISP. Schedule Type: The set
