Résumé du contenu de la page N° 1
®
HUAWEI
6. Security Configuration
7. VPN Configuration
8. Reliability Configuration
9. QoS Configuration
10. DDR Configuration
11. VoIP Configuration
VRP
User Manual – Configuration Guide
Volume 3
V200R001
Résumé du contenu de la page N° 2
VRP User Manual – Configuration Guide Volume 3 Manual Version T2-080168-20011213-C-1.5 Product Version V200R001 BOM 31010868 Copyright © 2001 by Huawei Technologies Co., Ltd. All Rights Reserved No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd. Trademarks ® ® , HUAWEI , C&C08, EAST8000, HONET, ViewPoint, INtess, ETS, DMC, SBS, TELLIN, InfoLink, Netkey, Quidway, SYNLOCK, Radium, , M900/M1800, TELE
Résumé du contenu de la page N° 3
About This Manual Contents To help readers to better understand, use and maintain Quidway series routers, we publish the manual suit of Quidway series routers. This manual suit includes: VRP User Manual Configuration Guide (V1.5) -Volume 1 VRP User Manual Configuration Guide (V1.5) -Volume 2 VRP User Manual Configuration Guide (V1.5) -Volume 3 VRP User Manual Command Reference (V1.5) -Volume 1 VRP User Manual Command Reference (V1.5) -Volume 2 VRP User Manual Command Reference (V1.5)
Résumé du contenu de la page N° 4
Module 10 DDR Configuration (10DC) This module mainly introduces the principle and specific configuration of dial solutions provided by VRP1.5, including Legacy DDR configuration, Dialer Profile configuration and modem management configuration. Module 11 VoIP Configuration (11VC) This module mainly introduces the principle and specific configuration of IP voice service features supported by VRP1.5, including configuration of VoIP, IP Fax, E1 voice, GK client and IPHC. Note: For questions r
Résumé du contenu de la page N° 5
Action Description Click Press the left button or right button quickly (left button by default). Double Click Press the left button twice continuously and quickly. Drag Press and hold the left button and drag it to a certain position. Symbol Some distinct symbols are employed in the manual to indicate the special notice that should be taken for the operation. The symbols are: Caution, Notice, Warning, Danger: Notify the special attention that should be given to the operation. Note, Prompt, Tip
Résumé du contenu de la page N° 6
® HUAWEI VRP User Manual – Configuration Guide Volume 3 11 – VoIP Configuration (VC)
Résumé du contenu de la page N° 7
Chapter 2 User Manual - Configuration Guide (Volume 3) Versatile Routing Platform IP Fax Configuration Chapter 2 IP Fax Configuration 2.1 Overview to IP Fax Traditional faxes are sent and received over PSTN. Today fax services are widely used due to its advantages, such as many kinds of transmissive information, fast speed for information transmission and easy to use. Type G3 facsimile machines are frequently used fax terminals in the current fax communications. Type G3 fax is a communication e
Résumé du contenu de la page N° 8
Chapter 2 User Manual - Configuration Guide (Volume 3) Versatile Routing Platform IP Fax Configuration IP telephone works after VoIP is configured. Generally speaking, faxes can now be sent and received by using the default configuration of IP Fax only after a facsimile machine is connected. The procedures of configuring IP Fax are mainly used to set up the specific parameters of IP Fax or used for some specified conditions. For example, fax operation can not be completed when the default gatewa
Résumé du contenu de la page N° 9
Chapter 2 User Manual - Configuration Guide (Volume 3) Versatile Routing Platform IP Fax Configuration If it is set to be the values except for “disable” and “voice”, the fax rate shall be set to be the corresponding values. The rate set here is not specified rate but the highest allowable rate. When the setting is voice mode (i.e. ”voice”), the highest allowable rate of fax should be finally determined by the differences among voice codec protocols. The fax rate is 14400bps if G.711 voice enco
Résumé du contenu de la page N° 10
Chapter 2 User Manual - Configuration Guide (Volume 3) Versatile Routing Platform IP Fax Configuration received “1” is less than the preset threshold value, then the current rate train is successful, otherwise, it is not successful. Please perform the following configuration in dial peer configuration mode. Table VC-2-4 Configure fax local-train threshold value Operation Command Configure fax local-train threshold value fax local-train threshold threshold Restore the default value of fax local-
Résumé du contenu de la page N° 11
Chapter 2 User Manual - Configuration Guide (Volume 3) Versatile Routing Platform IP Fax Configuration By default, the number for sending two kinds of redundancy packet is 0.The redundancy packet number for sending low-speed data ranges from 0 to 5, and the redundancy packet number for sending high-speed data ranges from 0 to 2. 2.2.8 Configuring the Fax Protocol Intercommunicating with Cisco Equipment The two kinds of fax protocols including T.38 and Cisco fax protocol are supported. When it i
Résumé du contenu de la page N° 12
Chapter 2 User Manual - Configuration Guide (Volume 3) Versatile Routing Platform IP Fax Configuration Table VC-2-9 Monitoring and maintenance of IP Fax Operation Command Open all of the debugging information switches of ipfax debug ipfax all Open the debugging information switch of function api of ipfax debug ipfax api Open the debugging information switch of main task of ipfax debug ipfax cc Open the debugging information switch of controller of ipfax debug ipfax controller Open the debugging
Résumé du contenu de la page N° 13
Chapter 2 User Manual - Configuration Guide (Volume 3) Versatile Routing Platform IP Fax Configuration Quidway(config-peer-voip1)# dial-peer voice 2 pots Quidway(config-peer-pots2)# destination 0101002 Quidway(config-peer-pots2)# port 2 The parameter settings for the router in Shenzhen is as follows: Quidway(config)# dial-peer voice 2 voip Quidway(config-peer-voip2)# destination 0101002 Quidway(config-peer-voip2)# session target ipv4:2.2.2.2 Quidway(config-peer-voip2)# dial-peer voice 1 pots Qui
