Résumé du contenu de la page N° 1
50 Minuteman Rd.
Andover, MA 01810
USA
Tel: (978) 684-1000
CUSTOMER RELEASE NOTES
X-Pedition Router
System Firmware Version E9.1.7.0
System Firmware Release Date: September 2003
INTRODUCTION:
This document provides specific information relevant to version E9.1.7.0 of the System Firmware for the X-Pedition
family of products. It includes content from the E9.0.7.7 System Firmware Maintenance Release and the E9.1.3.0A
patch release.
Enterasys Networks recommends
Résumé du contenu de la page N° 2
SYSTEM FIRMWARE SPECIFICATION SYSTEM FIRMWARE SPECIFICATION: Before installing the E9.1.7.0 System Firmware, the Boot Firmware should be upgraded to at least version E3.2.0.0. Refer to the E3.2.0.0 Boot Firmware Release Notes, or any X-Pedition Getting Started Guide, for instructions on upgrading the Boot Firmware. System Firmware File Name Version No. Release Date xp9170 E9.1.7.0 September 2003 xp9078 E9.0.7.8 September 2003 xp9080 E9.0.8.0 July 2003 xp9077 E9.0.7.7 July 2003
Résumé du contenu de la page N° 3
RELEASE NAMING CONVENTION RELEASE NAMING CONVENTION: Normally, the X-Pedition product family supports two active release lines. The older line is always in maintenance only mode and receives only maintenance improvements—the newer line receives maintenance improvements and introduces new features. For a brief time, however, the X-Pedition will support a special third line—E9.0.8. This line introduces the Security Attack Monitor (SAM) feature on the E9.0 code base. E9.0.8 is a mainte
Résumé du contenu de la page N° 4
RELEASE NAMING CONVENTION A release line is defined by the first two digits in the name, e.g. E9.0 and E9.1. The third digit increments with each release during the development phase of a line. For example, E9.0.7.0 is the seventh development release for the E9.0 line. The fourth digit is incremented with each release during the maintenance-only period of a release line. Thus E9.0.7.4 is the fourth maintenance-only release for the E9.0 line. Should a bug fix be required between regula
Résumé du contenu de la page N° 5
HARDWARE / FIRMWARE COMPATIBILITY HARDWARE / BOOT FIRMWARE/ SYSTEM FIRMWARE COMPATIBILITY: The Minimum Boot Firmware Version is a function of: • The hardware installed in the system (as listed below). • The version of VFS used. For more information on VFS versions see the “PCMCIA Card VFS Version” sub- section in the “INSTALLATION AND CONFIGURATION NOTES” section of the X-Pedition Boot Firmware Release Notes. • The need for new features or corrections that are provided in a specifi
Résumé du contenu de la page N° 6
HARDWARE / FIRMWARE COMPATIBILITY This version of System Firmware supports the X-Pedition Router hardware listed in the following table: Minimum Minimum System Boot Part Description Firmware Firmware Version Version 5SSRM-02 Router module for the Matrix E5 E8.0.1.0 1.1.0.8 6SSRLC-FX-AA 8-port 100BASE-FX (MT-RJ) module for 5SSRM-02 and 6SSRM-02 3.0.50.11 6SSRLC-LX-AA 2-port 1000BASE-LX module for 5SSRM-02 and 6SSRM-02 3.0.50.11 6SSRLC-LX70-AA 1-port 1000BASE-LX 70 KM module for
Résumé du contenu de la page N° 7
HARDWARE / FIRMWARE COMPATIBILITY Minimum Minimum System Boot Part Description Firmware Firmware Version Version SSR-2-LX70 1-port 70 km 1000BASE-LX module for X-Pedition 2000 2.0.0.0 SSR-2-LX70-AA 1-port 70 km 1000BASE-LX module for X-Pedition 2000 3.0.0.0 SSR-2-SER 2-port Serial module (No compression or encryption) for X-Pedition 2000 2.1.0.0 SSR-2-SER-AA 2-port Serial module (No compression or encryption) for X-Pedition 2000 3.0.0.0 SSR-2-SERC 4-port Serial module with comp
Résumé du contenu de la page N° 8
HARDWARE / FIRMWARE COMPATIBILITY Minimum Minimum System Boot Part Description Firmware Firmware Version Version SSR-HTX32-16 16-port 10/100 TX module (Cat 5 RJ-45) with 16 MB [T-Series] for X-Pedition 3.1.0.0 8000/8600 SSR-MEM-128 128MB Memory Upgrade Kit for SSR-CM2-64, SSR-CM2-128, SSR-CM3-128, and 1.1.0.0 1.1.0.2 ER16-CM3-128 SSR-MEM-256 256MB ECC Memory Upgrade Kit for SSR-CM4-256 and ER16-CM4-256 E9.0.7.4 or E3.3.0.0 E9.1.3.0 SSR-PCMCIA 8MB PCMCIA card for SSR-CM2-64, SSR
Résumé du contenu de la page N° 9
HARDWARE / FIRMWARE COMPATIBILITY Minimum Minimum System Boot Part Description Firmware Firmware Version Version XP-2-LX70-AA 1-port 70 km 1000BASE-LX module for X-Pedition 2400 E9.0.0.0 XP-2-SER-AA 2-port Serial module (No compression or encryption) for X-Pedition 2400 E9.0.0.0 XP-2-SERC-AA 4-port Serial module with compression (No encryption) for X-Pedition 2400 E9.0.0.0 XP-2-SERCE-AA 4-port Serial module with compression and encryption for X-Pedition 2400 E9.0.0.0 XP-2-SX-AA
Résumé du contenu de la page N° 10
HARDWARE / FIRMWARE COMPATIBILITY The following table lists supported hardware that is System Firmware and Boot Firmware version independent. Part Description APHY-21 SSR-ATM29-02 1 port OC-3 MMF Physical Interface Module APHY-22 SSR-ATM29-02 1 port OC-3 UTP Physical Interface Module APHY-29IR SSR-ATM29-02 1 port OC-3 SMF-IR Physical Interface Module APHY-67 SSR-ATM29-02 1 port DS-3/T3 Physical Interface Module (Coax) APHY-77 SSR-ATM29-02 1 port E-3 Physical Interface Module (Coax
Résumé du contenu de la page N° 11
HARDWARE REQUIREMENTS HARDWARE REQUIREMENTS TABLE: NOTE: X-Pedition line card hardware makes use of three basic ASIC versions (pre AA-series, AA-series and T- series). The features supported by each line card are roughly defined by which series of ASIC hardware is used on that card. The following table shows the hardware supporting specific features in this release: Pre AA – Series T – Series AA X-Pedition Description Feature Set / Part Number 5SSRM-02
Résumé du contenu de la page N° 12
HARDWARE REQUIREMENTS Pre AA – Series T – Series AA X-Pedition Description Feature Set / Part Number XP 2400 XP-2400 X-Pedition 2400 X X XX X X X X X X XP-2-ATM29-02 2-port ATM OC-3 X X X X X X X X X X X X X X X XP-2-FX-AA 8-port 100BASEFX X X XX X X X X X X XP-2-HSSI-AA 2-port HSSI X X XX X X X X X X XP-2-LX-AA 2-port 1000BASE-LX X XX X X X X X X XP-2-LX70-AA 1-port 70 km 1000BASE-LX X XX X X X X X X XP-2-S
Résumé du contenu de la page N° 13
HARDWARE REQUIREMENTS Pre AA – Series T – Series AA X-Pedition Description Feature Set / Part Number 4-port Serial, compression & SSR-SERCE-04 X encryption 4-port Serial, compression & SSR-SERCE-04-AA X X XX X X X X X X encryption ER16 ER16-04 4-port 1000BASE GBIC X X X X X X X X X X X X X X X ER16-08 8-port 1000BASE GBIC X X X X X X X X X X X X X X X ER16-ATM29-02 2-port ATM OC3 X X X X X X X
Résumé du contenu de la page N° 14
NETWORK MANAGEMENT SOFTWARE SUPPORT NETWORK MANAGEMENT SOFTWARE SUPPORT: The following table displays information on the Network Management Software that supports this release: NMS Platform Version Part Number NetSight Element Manager 3.1 NS-EM-CD NS-EM-LIC-1 NS-EM-LIC-5 NS-EM-LIC-10 NS-EM-LIC-20 NetSight Atlas Console 1.2 NSA-CD NSA-LIC NetSight Atlas Console Lite 1.2 NSA-L-CD NSA-L-LIC NetSight Atlas Inventory Manager 1.3 NSA-IM-CD NSA-IM-LIC NetSight Atlas Router Services
Résumé du contenu de la page N° 15
INSTALLATION AND CONFIGURATION NOTES INSTALLATION AND CONFIGURATION NOTES: Password Recovery If an X-Pedition password is lost and the user is unable to log in or enter Enable mode, please refer to the Enterasys Global Knowledgebase at http://knowledgebase.enterasys.com/esupport/ . Click Search by ID and enter TK0306-9. 10/02/03 P/N: 9038090-53 Subject to Change Without Notice Page: 15 of 31 F0615-J
Résumé du contenu de la page N° 16
NEW FEATURES AND ENHANCEMENTS IN E9.1.7.0 NEW FEATURES AND ENHANCEMENTS IN E9.1.7.0: NEW FIRMWARE SUPPORT The E9.1.7.0 system firmware provides support for the new features and enhancements below. For more information on any of these enhancements, please see the Enterasys X-Pedition User Reference Manual or Native CLI Reference Manual. 10-Gig Support of Link Aggregation SmartTRUNK no protocol link aggregation is now supported on 10-Gig interface modules (ER16-OS26-01 and ER16-OS
Résumé du contenu de la page N° 17
NEW FEATURES AND ENHANCEMENTS IN E9.1.7.0 Display of the System FPGA Revision A capability has been added that permits the display of the system FPGA revision number as illustrated in the example below. SYSTEM# system show hardware Hardware Information : System type : ER16, Rev. 0 CPU Module type : CPU-ER16 (CM4), Rev. 0 Processor : R7000, Rev 3.2, 380.00 MHz Icache size : 16 Kbytes, 32 bytes/line Dcache size : 16 Kbytes, 32 bytes/line CPU Board frequency : 95.
Résumé du contenu de la page N° 18
NEW FEATURES AND ENHANCEMENTS IN E9.1.7.0 NEW HARDWARE SUPPORT 10-Gigabit Ethernet (ER16-OS16-01) This release introduces support for the ER16-OS16-01, an optical fiber-based 10-Gigabit Ethernet module for the ER16 platform. This one slot card provides a single modular port of IEEE 802.3ae standards-based connectivity and its optical interfaces are based on fully compliant IEEE 802.3ae SC duplex fiber-optic connectors. Supported interfaces include the following: Part Number Con
Résumé du contenu de la page N° 19
ISSUES RESOLVED IN E9.1.7.0 ISSUES RESOLVED IN E9.1.7.0: The following tables provide brief descriptions of the issues resolved in this release. E9.1.7.0 includes all issues resolved in the E9.0.7.7 System Firmware Maintenance Release (see the E9.0.7.7 Release Notes for details). 10-Gigabit I.D. Priority queue settings on the ER16-OS26-01 may cause the X-Pedition to experience ingress buffer F4188 overflows. Entering the port show mc-vlan-encap all-ports command from the CLI erron
Résumé du contenu de la page N° 20
ISSUES RESOLVED IN E9.1.7.0 Hot Swap I.D. Under rare circumstances, the system may occasionally core when hot swapping a line card into the F2333 router. Internet Protocol (IP) I.D. If an X-Pedition with ip enable reverse flow all configured receives an invalid TCP/UDP packet of a F4345 specific type, the router may core. Layer-4 I.D. An X-Pedition configured with Layer-4 bridging will respond incorrectly to an ICMP request that is F4359 not destined for the router. F4297 Lin
