Instruction d'utilisation NETGEAR POE101

Résumé du contenu de la page N° 1

Power Over Ethernet Adapters
POE101
Installation Guide

Résumé du contenu de la page N° 2

Introduction NETGEAR POE101 Power over Ethernet adapters are designed to supply operational power to devices through an Ethernet cable. These adapters make it easy to extend reach of your wireless local network. The POE101 provides an ideal solution for locating an access point in a building ceiling or attic, for example, where it has optimal radio coverage without requiring an AC power outlet. The POE101 can extend the placement of a wireless access point up to 328 feet 1 (100 meters) by using

Résumé du contenu de la page N° 3

Package contents 1 1 POE101Base unit POE101 Terminal unit DC Power cables Power adapter Category 5 110v cord 100 Mbps Ethernet cable POE101 installation guide, support information card & warranty/registration card Wall mount kit • Power over Ethernet base unit • Power over Ethernet terminal unit • Localized AC power cable • 100~240 V AC to 24V DC 30W power adapter • Two 2-foot DC power cables • 2-foot Ethernet cable • Wall mount kit • Installation Guide • Warranty and support information car

Résumé du contenu de la page N° 4

Connect a Matched Pair of POE101 Adapters 2 2 Note: Use only in pairs of one base and one terminal unit only. Do NOT use two POE101 base units or two POE101 terminal units together. 1. Connect a straight-through category 5 Ethernet cable (not included in the package) from the Ethernet switch or hub to the POE101 base unit’s “LAN IN” port. 2. Plug in the the power to the POE base unit. Verify the POE101 base unit’s LED lights are lit. 3. Connect the a long straight-through category 3 5 AWG24 Eth

Résumé du contenu de la page N° 5

Now you should see that power is provided to the NETGEAR wireless access point. If there is no power, please refer to the Troubleshooting section in this guide. Please see the illustration below. Your final connection should be similar. DSL modem Cable/DSL Web Safe Router RP614 1 3 Power over Ethernet Base 10/100 BASE-T Power over Ethernet Terminal 10/100 BASE-T MODEL MODELPOE 101 POE 101 POE101Base unit POE101 Terminal unit 2 4 5 ME102 802.11b Wireless Access Point The total allowable distan

Résumé du contenu de la page N° 6

Troubleshooting Q: The base LED does not light up. A: Verify that the power supply connectors are properly connected. Q: The terminal LED does not light up. A: There are a couple of possibilities. Please check the following items in the sequence listed until everything works. 1. Verify you are using a terminal unit. 2. Verify that the POE101 base LED is lit. 4 3. Verify that the long Ethernet cable is a straight-through category 5, AWG24 or less cable . 4. Verify that the long Ethernet cable is

Résumé du contenu de la page N° 7

Statement of Conditions In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes to the product described in this document without notice. NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein. Certificate of the Manufacturer/Importer It is hereby certified that the NETGEAR Model POE101 Power over Ethernet adapters have been suppressed in

Résumé du contenu de la page N° 8

Product Specification AC power adapter Input: 100~240V AC 0.85A 50~60Hz Output: 24V DC 1.5A POE Base unit Power input: 24V DC 10/100 Mb LAN IN 10/100 Mb LAN OUT with 24V DC power POE Terminal unit 10/100Mb LAN IN with 24V DC power 10/100Mb LAN OUT Power output: 5V DC 2.5A max. Cables Category 5 with RJ-45 connectors for terminal to access point DC power cable for terminal unit to NETGEAR ME102 (North American version) DC power cable for terminal unit to all other NETGEAR 5V DC powered devices Lo