Résumé du contenu de la page N° 1
Setup Guide
IPL T S Series
Interfaces
68-1377-01 Rev. C
11 08
Résumé du contenu de la page N° 2
Precautions Safety Instructions • English Warning Power sources • This equipment should be operated only from the power source This symbol is intended to alert the user of important indicated on the product. This equipment is intended to be used with a main power operating and maintenance (servicing) instructions in system with a grounded (neutral) conductor. The third (grounding) pin is a safety the literature provided with the equipment. feature, do not attempt to bypass or disable it.
Résumé du contenu de la page N° 3
警告 安全须知 • 中文 电源 • 该设备只能使用产品上标明的电源。 设备 这个符号提示用户该设备用户手册中 必须使用有地线的供电系统供电。 第三条线 有重要的操作和维护说明。 （地线）是安全设施，不能不用或跳过。 拔掉电源 • 为安全地从设备拔掉电源，请拔掉所有设备后 这个符号警告用户该设备机壳内有暴 或桌面电源的电源线，或任何接到市电系统的电源线。 电源线保护 • 妥善布线， 避免被踩踏，或重物挤压。 露的危险电压，有触电危险。 维护 • 所有维修必须由认证的维修人员进行。 设备内部 注意 没有用户可以更换的零件。为避免出现触电危险不要自 阅读说明书 • 用户使用该设备前必须阅读并理 己试图打开设备盖子维修该设备。 解所有安全和使用说明。 通风孔 • 有些设备机壳上有通风槽或孔，它们是用来防止 保存说明书 • 用户应保存安全说明书以备将来使 机内敏感元件过热。 不要用任何东西挡住通风孔。 用。 锂电池 • 不正确的更换电池会有爆炸的危险。 必须使用 遵守警告 • 用户应遵守产品和用户指南上的所有安 与厂家推荐的相同或相近型号的电池。 按照生产厂的 全和操作说明。 建议处理废弃电
Résumé du contenu de la page N° 4
Résumé du contenu de la page N° 5
Table of Contents Chapter One • Introduction ................................................... 1-1 About this Manual .................................................................... 1-2 IPL T S Series Products .............................................................. 1-2 IPL T S1 ................................................................................... 1-3 IPL T S2 ................................................................................... 1-3 IPL T S4 ........
Résumé du contenu de la page N° 6
Table of Contents, cont’d Launching the GlobalViewer Interface ............................ 3-22 Step fourteen: launch GlobalViewer .................................. 3-22 All trademarks mentioned in this manual are the properties of their respective owners. 68-1377-01 Rev. C 11 08 ii IPL T S Series Interfaces • Table of Contents
Résumé du contenu de la page N° 7
IPL T S Series Interfaces Chapter One 1 Introduction About this Manual IPL T S Series Products Global Configurator
Résumé du contenu de la page N° 8
Introduction About this Manual This setup guide describes the: • IPL T S Series products • Global Configurator application • IPL T S Series hardware installation • IPL T S Series software configuration IPL T S Series Products The Extron IPL T S Series interface boxes can be installed as nodes on an Ethernet-based audio/video (A/V) network. They can be used to remotely monitor and control connected A/V devices such as projectors, displays, VCRs, DVD players, and lighting systems, etc. Light
Résumé du contenu de la page N° 9
The IPL T Series products include: IPL T S1 • 12 VDC power supply • RJ-45 Ethernet receptacle • 9-pin D RS-232 serial port IPL T S2 • 12 VDC power supply • RJ-45 Ethernet receptacle • Two 9-pin D RS-232, RS-422, or RS-485 serial ports - or - • Two 3.5 mm captive screw RS-232, RS-422, or RS-485 serial ports (common to the two 9-pin D serial ports). IPL T S4 • 12 VDC power supply • RJ-45 Ethernet receptacle • Four 9-pin D RS-232, RS-422, or RS-485 serial ports IPL T S6 • 12 VD
Résumé du contenu de la page N° 10
Introduction, cont’d Global Configurator Global Configurator (GC) is a software application that gives users the ability to create a single configuration file of all the controlled devices on their audio/video (A/V) network. There are two types of devices in an A/V system: ® • Controllers - Control devices that have an IP Link enabled Ethernet port for network connectivity, and serial, relay, I/O, and infrared (IR) ports for A/V device connectivity • Controlled devices - Audio/video pro
Résumé du contenu de la page N° 11
Using GC you can configure a single room controller, or create a web-based remote monitoring system for hundreds of A/V devices in multiple locations. You may configure an IPL T S Series interface using GC without having the device physically connected to the A/V network. Use Global Configurator version 2.2 or later. C Update all PCs and devices running earlier versions of GC. System requirements The minimum system requirements for the PC on which you install Global Configurator incl
Résumé du contenu de la page N° 12
Introduction, cont’d 1. Insert the Extron Software Products CD into your drive. 2. Wait for the Extron Software Products page to load. 3. Click on the Software icon. 4. Scroll down to the Global Configurator description and click the Install link in the far right column. 5. Follow the remaining system prompts. To install Global Configurator from an Extron Software Products CD if Autorun is not enabled on your PC: 1. Insert the Extron Software Products CD into your drive. 2. From the Wind
Résumé du contenu de la page N° 13
IPL T S Series Interfaces Chapter Two 2 Hardware Setup Front Panel Rear Panel Power Connection Local Area Network (LAN) Connection Serial Device Connection
Résumé du contenu de la page N° 14
Hardware Setup Front Panel The front panel has a recessed Reset button and the LED indicators described below: IPL T S1 Power LED — green when a power is on COM TX RTS R RX CTS Reset button — recessed IPL T S1 b multiple function reset 1 2 3 4 6 5 button TX LED — green when IPL T S2 c data is being transmitted IPL T S2 RX LED — green when COM d 100 data is being received R 1 LINK ACT 2 RTS LED — green when e ready to send data 1 2 3 4 5 6 7 8 9 CTS LED — green f when
Résumé du contenu de la page N° 15
Rear Panel The rear panel has connectors for power, control, signal input, and signal output, and indicators as described below. 10 IPL T S1 Power receptacle — a 00-05-A6-00-00-01 connects the supplied 12V 0.5 A 12 VDC power supply COM1 LAN LAN Activity LED — yellow b 1 6 2 3 4 LED blinks when sending and receiving data 10 6 IPL T S2 LAN receptacle — RJ-45 c receptacle for network COM1 00-05-A6-00-00-02 connection LAN POWER COM2 12V COM1 COM2 .5A MAX
Résumé du contenu de la page N° 16
Hardware Setup, cont’d Power Connection To connect the power supply: 1. Insert the 2-pole captive screw connector into the power supply receptacle on the rear panel of the interface. 2. Connect the female end of the power supply AC cord into the power supply and connect the male plug end into a 110 VAC receptacle. 00-05-A6-00-00-01 12V 0.5 A COM1 LAN Orange Captive Screw Connector Tie Wrap Ground +12 VDC External Power Supply (12 VDC, 1 A ) Local Area Network (LAN) Connect
Résumé du contenu de la page N° 17
Pinouts for the two types of Ethernet cables are shown below: Pins: Straight-through Cable 12345678 (for connection to a switch, hub, or router) End 1 End 2 Pin Wire Color Pin Wire Color 1 white-orange 1 white-orange 2 orange 2 orange 3 white-green 3 white-green 4 blue 4 blue 5 white-blue 5 white-blue 6 green 6 green Side View 7 white-brown 7 white-brown Insert 8 brown 8 brown Twisted Pair Wires RJ-45 Connector Crossover Cable (for direct connection to a PC) End 1 End 2 Pin Wire Co
Résumé du contenu de la page N° 18
Hardware Setup, cont’d 9-pin D connector Connect any audio/video device using a serial cable with a 9-pin D connector to any one of the COM ports on the rear panel of an IPL T S Series interface. COM1 00-05-A6-00-00-02 LAN POWER COM2 IPL T S2 12V COM1 COM2 .5A MAX TX RX TX RX COM Ports with 9-pin D Connectors Pinouts for the 9-pin D connector are shown in the illustration and table below. 51 96 9-Pin D Connector Pinouts Pin Function RS-232 RS-422 RS-485 2 Receive Data/Receive Data -
Résumé du contenu de la page N° 19
COM1 00-05-A6-00-00-02 LAN POWER COM2 IPL T S2 12V COM1 COM2 .5A MAX TX RX TX RX COM Ports with Captive Screw Connectors The IPL T S6 has four COM ports (3 thru 6) with captive screw connectors that are independent of COM ports 1 and 2, which have 9-pin D connectors. COM Ports with 9-pin D COM1 00-05-A6-00-00-06 Connectors LAN POWER COM2 12V IPL T S6 COM3 COM4 COM5 COM6 .5A MAX TX RX TX RX TX RX TX RX COM Ports with Captive Screw Connectors The IPL T S2 and S6 female ca
Résumé du contenu de la page N° 20
Hardware Setup, cont’d 2-8 IPL T S Series Interfaces • Hardware Setup
