Instruction d'utilisation Delta Electronics LCP-200A4HSR

Résumé du contenu de la page N° 1

RoHS Compliant Small Form Factor Pluggable Transceiver RoHS
Compliant for ESCON, Fast Ethernet, ATM, SONET OC-3/SDH STM-1
FEATURES
Compliant with SFP Transceiver MSA
specification
Compliant with Industry Standard RFT
Electrical Connector and Cage
1310nm LED Source Technology
Single + 3.3V Power Supply and TTL Logic
Interface
EEPROM with Serial ID Functionality
Laser Class 1 Product which comply with the
requirements of IEC 60825-1 and IEC 60825-2
Duplex LC Connector interf

Résumé du contenu de la page N° 2

Absolute Maximum Ratings Parameter SymbolMin. Typ. Max. Unit Note Storage Temperature Ts -40 85 ºC Supply Voltage VCC 0 5 V Recommended Operating Conditions Parameter SymbolMin. Typ. Max. Unit Note Case Operating Temperature TC -5 70 ºC 1 Supply Voltage VCC 3.135 3.465 V Note 1: See order information Electrical Characteristics (V =3.135V to 3.465V) CC Parameter SymbolMin. Typ. Max. Unit Note Total Supply Current ICCT 300 mA Transmitter Transmitter Differential Input V

Résumé du contenu de la page N° 3

Optical Characteristics 23 (V =3.135V to 3.465V, Data Rate=200Mb/sec, PRBS=2 -1 NRZ, 62.5/125um MMF) CC Parameter Symbol Min. Typ. Max. Unit Note Transmitter Output Optical Power (Avg.) P dBm -20 -14 O Optical Extinction Ratio 9 dB Center Wavelength 1310 nm C Spectral Width (RMS) nm 200 Optical rise time/ fall time t /t 3 ns 1 r f Relative Intensity Noise RIN -117 dB/Hz Receiver Sensitivity (Avg.) P dBm 2 -31 IN Input Optical Wavelength 1100 1310 1600

Résumé du contenu de la page N° 4

SFP Transceiver Electrical Pad Layout Pin Function Definitions Pin Num. Name Function Plug Seq. Notes 1 VeeT Transmitter Ground 1 2 TX Fault Transmitter Fault Indication 3 Note 1 Note 2 3 TX Disable Transmitter Disable 3 Module disables on high or open 4 MOD-DEF2 Module Definition 2 3 Note 3, 2 wire serial ID interface 5 MOD-DEF1 Module Definition 1 3 Note 3, 2 wire serial ID interface 6 MOD-DEF0 Module Definition 0 3 Note 3, Grounded in Module 7 Rate Select Not Connect 3 Func

Résumé du contenu de la page N° 5

Notes: 1) TX Fault is an open collector/drain output, which should be pulled up with a 4.7K – 10K Ω resistor on the host board. Pull up voltage between 2.0V and VccT, R+0.3V. When high, output indicates a laser fault of some kind. Low indicates normal operation. In the low state, the output will be pulled to < 0.8V. 2) TX disable is an input that is used to shut down the transmitter optical output. It is pulled up within the module with a 4.7 – 10 K Ω resistor. Its states are: Low (0 –

Résumé du contenu de la page N° 6

Recommend Circuit Schematic 1uH VCC 3.3V Protocol Vcc DELTA SFP Module 1uH 10uF 0.1uF VccT 0.1uF 10k Ohms Tx_Disable Tx_Disable Tx_Fault TD + 0.01uF Laser Driver 100 Ohms Laser Diode TD - 0.01uF VeeT Protocol IC SerDes IC VccR RES1 10uF 0.1uF RD + 0.01uF Preamp & Quantizer 100 Ohms* Photo Diode RD - 0.01uF Rx_LOS Rx_LOS 3.3V VeeR RES1 RES1 RES1 Mod_def 2 PLD / PAL EEPROM Mod_def 1 Mod_def 0 RES1 = 4.7k to 10k Ohms * Depands on SerDes IC used 6 Aug., 2006 Rev. 0A DELTA ELECTRONICS, INC. ww

Résumé du contenu de la page N° 7

Package Outline Drawing for Metal Housing with Bail de-latch 7 Aug., 2006 Rev. 0A DELTA ELECTRONICS, INC. www.deltaww.com

Résumé du contenu de la page N° 8

SFP timing parameters for SFP management Parameter Symbol Min.Max.Unit Unit Conditions Time from rising edge of TX_DISABLE to TX_DISABLE Assert t_off 10 µsec when the optical output falls below 10% of time nominal Time from falling edge of TX_DISABLE to TX_DISABLE t_on 1 msec when the modulated optical output rises Negate time above 90% of nominal Time to initialize, From power on or negation of TX_Fault using including reset of t_init 300msec TX Disable. TX_FAULT TX Fau

Résumé du contenu de la page N° 9

Regulatory Compliance Feature Reference Performance Electromagnetic Interference FCC Class B (EMI) EN 55022 Class B (CISPR 22A) Radio Frequency EN 61000-4-3 Electromagnetic Field (1) Satisfied with electrical IEC 1000-4-3 characteristics of product spec. Electrostatic Discharge to the EN 61000-4-2 Duplex LC Receptacle (2) No physical damage IEC 1000-4-2 IEC 801.2 Electrostatic Discharge to the MIL-STD-883E Method 3015.7 Electrical Pins Eye Safety US FDA CDRH AEL Class 1