Instruction d'utilisation Z Microsystems 8X

Instruction d'utilisation pour le dispositif Z Microsystems 8X

Dispositif: Z Microsystems 8X
Catégorie: Carte réseau
Fabricant: Z Microsystems
Dimension: 3.16 MB
Date d'addition: 2/20/2013
Nombre des pages: 51
Imprimez l'instruction

Téléchargez

Comment utiliser?

Notre objectif consiste à vous assurer le plus rapide accès au contenu de l'instruction d'utilisation du dispositif Z Microsystems 8X. En utilisant l'aperçu en ligne vous pouvez parcourir le sommaire et passer à la page où vous trouverez la résolution de votre problème avec Z Microsystems 8X.

Pour votre confort

Si regarder l'instruction Z Microsystems 8X directement sur la page n'est pas confortable pour vous, vous pouvez profiter de deux solutions possibles:

  • Exploration au mode de plein écran - pour analyser l'instruction d'une manière commode (sans l'avoir téléchargée sur votre ordinateur) vous pouvez utiliser le mode d'exploration en plein écran. Pour démarrer l'exploration de l'instruction Z Microsystems 8X en plein écran, utilisez le bouton Plein écran.
  • Téléchargement sur l'ordinateur - vous pouvez aussi télécharger l'instruction Z Microsystems 8X sur votre ordinateur et la sauvegarder dans vos ressources. Si vous n'avez pas envie de gaspiller votre espace disque, vous pouvez toujours télécharger cette instruction du ManualsBase dans l'avenir.
Z Microsystems 8X Manuel d'utilisation - Online PDF
Advertisement
« Page 1 of 51 »
Advertisement
Version imprimée

Beaucoup de gens préfèrent de lire les documents dans la version imprimée et non pas sur l'écran. L'option d'impression de l'instruction est aussi prévue et vous pouvez en profiter en cliquant le lien ci-dessus - Imprimez l'instruction. Il n'est pas nécessaire d'imprimer toute l'instruction Z Microsystems 8X - on peut choisir des pages. Economisez le papier.

Résumés

Vous trouverez ci-dessous les annonces des contenus qui se trouvent sur les pages suivantes de l'instruction de Z Microsystems 8X. Si vous voulez parcourir rapidement le contenu des pages suivantes de l'instruction, vous pouvez en profiter.

Résumés du contenu
Résumé du contenu de la page N° 1

FIELD-READY
T ranzStor
8X
User Manual
Z Microsystems

Résumé du contenu de la page N° 2

REGULATORY WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED AS PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS ALL THREE PRONGS CAN BE FULLY INSERTED 2. Changes or modifi - 1. Use the power cable cations not expressly supplied with the product approved by Z Microsys- to help prevent interfer- tems could void user’s ence with radio and televi- warranty. sion reception. The use of cables and adapte

Résumé du contenu de la page N° 3

TABLE OF CONTENTS SECTION PAGE Introduction ........................................................................................................ 4 About This Manual ............................................................................................ 4 Safety Precautions ............................................................................................ 4 Product Description ........................................................................................... 5 I

Résumé du contenu de la page N° 4

INTRODUCTION ABOUT MANUAL This Manual is also available on the Z Microsystems website (www.zmicro.com). We recommend you read this manual carefully and follow the instructions in the Installation chapter for verifi cation of system functions and control settings. SAFETY PRECAUTIONS DANGER: To avoid shock hazard: • Do not penetrate the 8X with any screw longer than .18”. Damage will occur. • Do not connect or disconnect the 8X during an electrical storm. • Th e power cord plug must be conne

Résumé du contenu de la page N° 5

INTRODUCTION PRODUCT DESCRIPTION From the TranzStor family of low-profi le, platform-independent network storage solu- tions comes the TranzStor 8X SC (SCSI Controller). Featuring an Ultra 160 (or Ultra 320) SCSI to SCSI RAID controller and 8 hot-swappable TranzPak 7 hard drive modules. The TranzStor 8X SC RAID array provides data intensive, mission critical applications with the high-end availability, performance and fault-tolerance they require. Packed in a tough, lightweight, compact alumi

Résumé du contenu de la page N° 6

INSTALLATION INSTALLATION This portion of the Operations chapter is for quick reference only. For a more detailed description of RAID confi gurations, see the Controller Manufacturer’s user manual. Shipment Contents: (8) Nut, Locking, 10-32, SS, 01- 8X Raid Enclosure (Power Sup- e a 92151 plies and TP7s installed) (4) Screw, 10-32 x 0.75 Pan Phil- (6) Screw, SEM, Phillips, 10-32 b f lips, 01-92112 x 1.00”, SS, 01-92220 (8) Screw, 10-32 x 0.50 Pan Phil- g lips SS ISEM, (4) Screw, Pkh, Phill

Résumé du contenu de la page N° 7

INSTALLATION Raid Controller Manual Null Modem Cable (DB9F to DB9F) i m j n Warranty & Service Plan IEC Power Cable o k 8X User Manual Rack Slides p Electronic Documentation l SCSI LVD/SE External Terminators (Quantities will vary depending on RAID Controller Model) j i k l n m p o 7 Doc# 27-0030UM Rev 1.0 Issued 12/04

Résumé du contenu de la page N° 8

INSTALLATION REQUIRED TOOLS • Phillips Head Screwdriver • 3/8” ratchet PREPARATIONS In preparation to install the 8X, take the following precautionary steps: Turn off the electrical power to the host computer. INSTALLATION PRECAUTIONS When mounting the 8X, there is a maximum of .18” screw penetration on the underside and side screw hole locations. NOTE: For the fastest and easiest installation of the 8X, follow these steps in the sequence they are presented. 8 Doc# 27-0030UM Rev 1.

Résumé du contenu de la page N° 9

INSTALLATION STEP 1: RAIL INSTALLATION The 8X RAID will arrive with the slides unattached. Slide Extension Bracket Outer Slide Member To attach the slides to the extension brackets, use two panhead phillips screws (part# 01-91622), two fl at washers (01- 91872), and two lock washers (01-92151). Positioning the slide assembly on the Insert the screws through the slots of the inside of the rack, secure the front of the extension bracket and into the holes in the outer slide member. Secure

Résumé du contenu de la page N° 10

INSTALLATION Middle Slide Member Inner Slide Member Once both slide assemblies are installed Extend the inner members of the slide as- semblies out as far as they will go. in the rack, extend the middle members of the slide assemblies out of the rack. Press the slide locking tab on the outer and remove the inner members of the slide sides of the slides... assemblies. Attach the inner members to the sides of Lay the inner members along either side of the 8X RAID, placing the pointed end of

Résumé du contenu de la page N° 11

INSTALLATION STEP 2: 8X RAID INSTALLATION CAUTION: When attaching the inner members of the slide assemblies to the sides of the 8X RAID, ensure screw penetration does not exceed 3/16” length. Damage may result if screw length exceeds 3/16” length. Use 10-32 x 3/16” screws only (part# 01-91827). Hold the 8X RAID up to the extended Slide the unit in until the slide action stops. rails with the rear of the 8X RAID to the rear of the rack. Insert the inner member (attached to the 8X RAI

Résumé du contenu de la page N° 12

INSTALLATION STEP 3: CABLE CONNECTIONS The picture below shows the rear of a TranzStor 8X RAID unit and the connection points for these cables. TranzStor 8X confi gurations may vary. 1. Terminate external SCSI connectors 2. Connect SCSI Adapter to Host Computer’s SCSI adapter using a 68 pin external SCSI cable. 3. Connect Serial CTRL A to the Host Computer’s COM 1 port using the modem cable. 4. Connect power cable. Install LVD/SE Terminators SCSI Adapter Serial CTRL A AC Power Plug 12

Résumé du contenu de la page N° 13

OPERATIONS STEP 4: POWER UP TRANZSTOR 8X Before powering the TranzStor 8X, make sure all of the connections are tightened se- curely at the rear of the unit. Then press the power switch on the front of the 8X. Power Switch, Front After turning on the power switch, the controller will beep. Watch the amber activity lights. All of the drives’ activity LEDs will illuminate briefl y, and then extinguish. STEP 5: ESTABLISH SERIAL CONNECTION From Accessories/Comunications/ select Hyperterminal. C

Résumé du contenu de la page N° 14

OPERATIONS STEP 6: VERIFY CHANNEL SETTINGS If you’re not at the “Main Menu”, select “PC Graphic (ANSI Mode)” and press “Enter”. This will take you to the “Main Menu”. Verify that your channel settings match the image below. If your channel settings do NOT match, you can not continue with the Quick Guide set-up. Please refer to the troubleshoot- ing section of this manual. 14 Doc# 27-0030UM Rev 1.0 Issued 12/04

Résumé du contenu de la page N° 15

OPERATIONS STEP 7: BEGIN QUICK INSTALL WIZARD Create logical drive. Select top option. See controller user manual for other RAID options. Initialization will begin, and will continue for up to two hours, depending on the drive ca- pacity (about 2 hours for a 146 GB drive). 15 Doc# 27-0030UM Rev 1.0 Issued 12/04

Résumé du contenu de la page N° 16

OPERATIONS Once the initialization is complete, the progress counter will disappear. Press the “ESC” key. Select “System Functions,” then “Reset the Controller,” and fi nally “Yes” to reset. 16 Doc# 27-0030UM Rev 1.0 Issued 12/04

Résumé du contenu de la page N° 17

OPERATIONS STEP 8: ADD NEW LOGICAL DRIVE After the TranzStor 8X system reboots, rescan the SCSI bus on the host computer by right-clicking on the SCSI controller in the device manager. NOTE: Th e following screens are Win2K screens, and may appear diff erently with diff erent operating systems. Go to Administrative Tools>Computer Management>Disk Management. Click on “Disk Management” to start up Write Signature and Upgrade Wizard. Follow the steps in the Wizard. 17 Doc# 27-0030UM Rev 1.0

Résumé du contenu de la page N° 18

OPERATIONS The host OS should fi nd a new disk with unallocated space and start up the Create Volume Wizard automatically. If the Wizard doesn’t start up automaically, right-click on unallocated disk and select “create volume”. NOTE: If the Disk symbol is shown as “unallocated” (has a red negative symbol over the drive symbol), there is no signature written to the drive. To do so, right click on the disk, and write a signature for the drive in the window that appears. Click “OK”. Th e red ne

Résumé du contenu de la page N° 19

OPERATIONS Once complete, the new drive can be found in the same fi le location as the fi rst available drive under “My Computer”. 19 Doc# 27-0030UM Rev 1.0 Issued 12/04

Résumé du contenu de la page N° 20

OPERATIONS STATUS INDICATORS The drives are numbered one through eight. Each drive has two dedicated status indicator LEDs just below the drive. The following indicators apply to the drives only: Green= When the drive is plugged into the TranzStor 8X, the green light indicates the drive has power. Yellow= The yellow light comes on when the drive is accessed by the controller, indicating activity on the drive. Power Activity System Power Indicator Drive Status Indicator Alert Indicator Th


Instructions pareilles
# Instruction d'utilisation Catégorie Téléchargez
1 Z Microsystems Multi Processor Unit Z MPU Manuel d'utilisation Carte réseau 0
2 Sony BTA-NW1A Manuel d'utilisation Carte réseau 2
3 Sony BKMW-E3000 Manuel d'utilisation Carte réseau 2
4 Sony AC-SQ950D Manuel d'utilisation Carte réseau 0
5 Sony BBV RX100 Manuel d'utilisation Carte réseau 3
6 Sony CLIE A-AVZ-100-11 Manuel d'utilisation Carte réseau 1
7 Sony BTA-NW1 Manuel d'utilisation Carte réseau 11
8 Sony AC-NWUM50 Manuel d'utilisation Carte réseau 1
9 Sony AR-B1474 Manuel d'utilisation Carte réseau 2
10 Sony BKM-FW32 Manuel d'utilisation Carte réseau 1
11 Sony 4000CL-MAV-PBIO Manuel d'utilisation Carte réseau 1
12 Sony FA-ST1AM Manuel d'utilisation Carte réseau 0
13 Sony MVC-FDR3/FDR3E Manuel d'utilisation Carte réseau 1
14 2Wire third-party wireless Ethernet adapters Manuel d'utilisation Carte réseau 1
15 3Com 10/100BASE-T4 PCI Manuel d'utilisation Carte réseau 1