Résumé du contenu de la page N° 1
TANDBERG 3G Gateway Data port Command Interface User Guide
TANDBERG 3G Gateway
Data port Command Interface User Guide
Software version R 3
D1320203
TANDBERG
D1320203 1
Résumé du contenu de la page N° 2
TANDBERG 3G Gateway Data port Command Interface User Guide Table of Contents 1. INTRODUCTION...........................................................................................................................3 2. CONNECTING TO THE DATA PORT COMMAND INTERFACE THROUGH THE RS-232 PORT. 4 2.1. HARDWARE AND CABLING............................................................................................................4 2.2. TROUBLESHO
Résumé du contenu de la page N° 3
TANDBERG 3G Gateway Data port Command Interface User Guide 1. Introduction The TANDBERG 3G Gateway Data port Command Interface User Guide contains guidelines on how to use the textual command interface supported by the 3G Gateway system, further referred to as 3G Gateway. The Data port Command Interface can be accessed through Telnet via the LAN interface or through RS-232 by connecting a serial cable to the serial interface connector, refer
Résumé du contenu de la page N° 4
TANDBERG 3G Gateway Data port Command Interface User Guide 2. Connecting to the Data port Command Interface through the RS-232 port. The RS-232 port is a 9-pin, female, sub-D connector located on the front of the 3G Gateway. The port is configured as a DCE (Data Communications Equipment). The RS-232 port is default set to 115200 baud, 8 data bits, none parity and 1 stop bit from factory. The RS-232 port is also referred to as the Data port.
Résumé du contenu de la page N° 5
TANDBERG 3G Gateway Data port Command Interface User Guide If communication cannot be established between the PC/terminal and the TANDBERG 3G Gateway’s Data port the following should be checked: • Verify that the serial cable is a straight through 9-pin to 9-pin cable • Confirm that the configuration of the PC/terminal’s serial RS-232 port is identical to the configuration of the TANDBERG 3G Gateway RS-232 port. • Verify that the PC/termin
Résumé du contenu de la page N° 6
TANDBERG 3G Gateway Data port Command Interface User Guide 3. Connecting to the Data port Command Interface using Telnet The TANDBERG 3G Gateway has one LAN port. The 3G Gateway’s Telnet server provides access to the Data port Command Interface through a 10/100 base T network interface supporting the TCP/IP protocol. When connected to the 3G Gateway, type tsh to start a t-shell from the command line. The Telnet client will receive a welcome
Résumé du contenu de la page N° 7
TANDBERG 3G Gateway Data port Command Interface User Guide 4. The TANDBERG 3G Gateway Commands 4.1. Introduction Typing ‘?’ or ‘help’ when connected to the Data Port Command Interface will return a list of valid commands. The commands are used to control the functions of the 3G Gateway. A command may be followed by a set of parameters and sub-commands. This chapter gives a description of all valid commands for the 3G Gateway. 4.1.1. Comman
Résumé du contenu de la page N° 8
TANDBERG 3G Gateway Data port Command Interface User Guide 4.1.2. Command types The commands can be divided into three major classes: • Parameter Configuration Commands, Xconf. • Status Commands, Xstat. • User Commands, Xcom. Parameter Configuration Commands are commands that set a system parameter to a specific value. E.g.: The command Xconf telnet mode: "on" enables telnet access on the 3G Gateway. If the command is syntactically correc
Résumé du contenu de la page N° 9
TANDBERG 3G Gateway Data port Command Interface User Guide 4.2.1. System Configuration Commands Command: Description: Dialplan Mapping of a call onto a service or another call. Dialplan Entry [1..64] Enabled: Dialplan Entry [1..64] Name: Dialplan Entry [1..64] NetType: Dialplan Entry [1..64] Prefix: Dialplan Entry [1..64] Suffix: Dialplan Entry [1..64] ServiceI
Résumé du contenu de la page N° 10
TANDBERG 3G Gateway Data port Command Interface User Guide distinguished: • Net type - Either H324m, H323 or SIP of the outbound call. • AV mode – This mode determines the outbound audio and video call settings. It is either Audio Only, Audio + Video, Auto(matic) no fallback to audio, Auto + fallback to audio and Auto + always fallback to audio. In the “Audio Only” mode a voice call is being setup, even when all endpoints support both audio
Résumé du contenu de la page N° 11
TANDBERG 3G Gateway Data port Command Interface User Guide *c xConfiguration Dialplan Entry 1 Prefix: "207947133" *c xConfiguration Dialplan Entry 1 Suffix: "" *c xConfiguration Dialplan Entry 1 ServiceId: 1 *c xConfiguration Dialplan Entry 1 Property 1 Name: "nettype" *c xConfiguration Dialplan Entry 1 Property 1 Value: "SIP" *c xConfiguration Dialplan Entry 1 Property 2 Name: "avmode" *c xConfiguration Dialplan Entry 1 Prop
Résumé du contenu de la page N° 12
TANDBERG 3G Gateway Data port Command Interface User Guide *c xConfiguration Dialplan Entry 2 Property 2 Name: "avmode" *c xConfiguration Dialplan Entry 2 Property 2 Value: "4" *c xConfiguration Dialplan Entry 2 Property 3 Name: "prefix" *c xConfiguration Dialplan Entry 2 Property 3 Value: "" *c xConfiguration Dialplan Entry 2 Property 4 Name: "suffix" *c xConfiguration Dialplan Entry 2 Property 4 Value: "" *c xConfiguration
Résumé du contenu de la page N° 13
TANDBERG 3G Gateway Data port Command Interface User Guide *c xConfiguration Dialplan Entry 4 Prefix: "90370010" *c xConfiguration Dialplan Entry 4 Suffix: "" *c xConfiguration Dialplan Entry 4 ServiceId: 3 *c xConfiguration Dialplan Entry 4 Property 1 Name: "allowredirectep" *c xConfiguration Dialplan Entry 4 Property 1 Value: "0" *c xConfiguration Dialplan Entry 4 Property 2 Name: "entry1_label" *c xConfiguration Dialplan E
Résumé du contenu de la page N° 14
TANDBERG 3G Gateway Data port Command Interface User Guide *c xConfiguration Dialplan Entry 4 Property 14 Name: "entry5_label" *c xConfiguration Dialplan Entry 4 Property 14 Value: "Menu" *c xConfiguration Dialplan Entry 4 Property 15 Name: "entry5_nettype" *c xConfiguration Dialplan Entry 4 Property 15 Value: "H323" *c xConfiguration Dialplan Entry 4 Property 16 Name: "entry5_bnumber" *c xConfiguration Dialplan Entry 4 Property 1
Résumé du contenu de la page N° 15
TANDBERG 3G Gateway Data port Command Interface User Guide • Authentication Mode configures the use of authentication against a gatekeeper. • Authentication ID Configures the user name used within an authentication challenge • Authentication Password sets the password used within the authentication process. NOTE! Authentication Password is write only. Example of H323Gatekeeper feedback: Xconf H323Gatekeeper Authentication *c xConfi
Résumé du contenu de la page N° 16
TANDBERG 3G Gateway Data port Command Interface User Guide used when the 3G Gateway is connected to a LAN using DHCP. When using this mode, IP-address and IP-subnet mask are not used because the DHCP server supplies these parameters. • Address: Sets the static IP address for the given LAN interface. • Subnetmask: Sets the subnet mask variable. Subnet mask defines the network class. If the setting is 255.255.255.0 the local network will supp
Résumé du contenu de la page N° 17
TANDBERG 3G Gateway Data port Command Interface User Guide *c xConfiguration ISDN InternationalPrefix: "00" Loadlimit Sets the processor-load percentage at which calls should be routed to another 3G Gateway. LoadLimit: <0..100> Example of Loadlimit feedback: *c xConfiguration LoadLimit: 85 Session Sets a timeout time for sessions like telnet, ssh etc. Session TimeOut: <0..65535> Example of Session feedback: *c xConfiguration
Résumé du contenu de la page N° 18
TANDBERG 3G Gateway Data port Command Interface User Guide SNMP HostIPAddr [1..3]: --- parameters: • Mode: < On/Off/ReadOnly/TrapsOnly > • Community Name: Text string of maximum 16 characters. • System Contact: Text string of maximum 70 characters • System Location: Text string of maximum 70 characters • Host IP Addr: The IP addresses of max 3 SNMP trap hosts sub-commands: • Mode enables or sets the mode of SNMP support
Résumé du contenu de la page N° 19
TANDBERG 3G Gateway Data port Command Interface User Guide Telnet Enables or disables telnet interface on the 3G Gateway Telnet Mode: --- Example of Telnet feedback: *c xConfiguration Telnet Mode: On D1320203 19
Résumé du contenu de la page N° 20
TANDBERG 3G Gateway Data port Command Interface User Guide 4.2.2. General 3G Gateway Commands Command: Description: ExternalManager This command sets the path and address of the TMS server. A message is sent to TMS when the 3G Gateway starts up to signal TMS that the 3G Gateway is ready. ExternalManager Path: or ExternalManager Address: -- sub-commands: • Path • Address, the IP address of the manager Exam
