Résumé du contenu de la page N° 11
IMPORTANT Note on RDY* Input: •Be sure to input "L" to the RDY* pin of the target system during the user program executing (only while the RUN status LED on the PC4701's front panel is lit). Inputting "L" to the RDY* pin during the user program stopping may cause a malfunction of the emulator. Note on HOLD* Input: • Be sure to input "L" to the HOLD* pin of the target system during the user program executing (only while the RUN status LED on the PC4701's front panel is lit). Inputting "L" to the
Résumé du contenu de la page N° 12
IMPORTANT Notes on Stack Area: • With this product, a maximum 20 bytes of the user stack is consumed as work area. • If the user stack does not have enough area, do not use areas which cannot be used as stack (SFR area, RAM area which stores data, or ROM area) as work area. Using areas like this is a cause of user program crashes and destabilized emulator control. Therefore, ensure the +20 byte maximum capacity used by the user program as the user stack area. •With this product, the interrupt st
Résumé du contenu de la page N° 13
IMPORTANT Notes on EMEM Dialog: Observe the following when setting up EMEM dialog of the emulator debugger. (1) Debug Monitor Bank Address • When "F0" is specified, 64 KB of area starting from F00000h are allocated for use by the debug monitor. • The 64 KB allocated to the debug monitor cannot be used. • The below areas cannot be set for the debug monitor. (1) MCU internal resources (RAM/SFR area) (2) DRAM area or multiplex area (3) Interrupt vector area • It is not possible to view or set the c
Résumé du contenu de la page N° 14
IMPORTANT Note on Differences between Actual MCU and Emulator: •Operations of the emulator differs from those of mask MCUs as listed below. (1) Reset condition (2) Initial values of internal resource data at power-on (3) Interrupt stack pointer (ISP) after releasing reset (4) Internal memories (ROM and RAM) capacities, etc. This emulator system has an MCU with 24KB RAM (0400h - 63FFh). In single-chip mode or memory expansion mode, emulation memory for internal ROM is automatically allocated in t
Résumé du contenu de la page N° 15
IMPORTANT Notes on A-D Input Selection Function: • To use A-D input group selection, it is necessary to set the direction register of port P10 to input. Port 10 corresponds to the pin that performs A-D conversion. Example: To select A-D input for P00-P07, set the direction register of P100-P107 and P00-P07 to input. Also, when the port P0 group and port P2 group are selected for A-D input, port P10 cannot be used as an I/O port. • Because a flexible board and other elements exist between the eva
Résumé du contenu de la page N° 16
MEMO ( 16 / 74 )
Résumé du contenu de la page N° 1
M30803T-RPD-E
Emulation Pod for M16C/80 Group MCUs
User's Manual
Rev. 1.00
July 1, 2003
REJ10J0197-0100Z
Résumé du contenu de la page N° 2
* IC61-1004-051 is a product of Yamaichi Electronics Co., Ltd. * NQPACK, YQPACK, YQSOCKET, YQ-Guide, HQPACK, TQPACK and TQSOCKET are products of Tokyo Eletech Corporation. Keep safety first in your circuit designs! • Renesas Technology Corporation and Renesas Solutions Corporation put the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or
Résumé du contenu de la page N° 3
Preface The M30803T-RPD-E is an emulation pod for the M16C/80 Group of Renesas 16-bit MCUs. It's used with a PC4701 emulator. This user's manual mainly describes specifications of the M30803T-RPD-E emulation pod and how to setup it. For details on the following products, which are used with M30803T-RPD-E, refer to each product's user's manual. • Emulator: PC4701 User's Manual • Emulator debugger: M3T-PD308 User's Manual All the components of this product are shown in "Table 2.1 Package component
Résumé du contenu de la page N° 4
Contents Chapter 1. Precautions for Safety ..........................................................................................7 1.1 Safety Symbols and Meanings .............................................................................8 Chapter 2. Preparation .........................................................................................................17 2.1 Terminology .......................................................................................................
Résumé du contenu de la page N° 17
Chapter 2. Preparation This chapter describes the package components, the system configuration and the preparation for using this product for the first time. 2.1 Terminology ............................................................................................................................... 18 2.2 Package Components.................................................................................................................. 19 2.3 Other Tool Products Required for Development......
Résumé du contenu de la page N° 18
Chapter 2. Preparation 2.1 Terminology Some specific words used in this user's manual are defined as follows: Emulator system This means an emulator system built around the PC4701 emulator. The PC4701 emulator system is configured with an emulator main unit, emulation pod, host machine and emulator debugger. Emulator main unit (Hereafter PC4701) This means a generic name for emulators for 8 and 16-bit MCUs. For details on specific models of PC4701, visit Renesas Tools Homepage. Homepage URL h
Résumé du contenu de la page N° 19
2.2 Package Components The M30803T-RPD-E package consists of the following items. When unpacking, check to see if your M30803T-RPD-E contains all of these items. Table 2.1 Package components Item Quantity M30803T-RPD-E emulation pod main unit 1 FLX120-RPD flexible cable for connecting emulator main unit 1 FLX160-PRB converter board for connecting FLX160 to M30800T-PTC 1 (mounted on FLX160) M30800T-PTC converter board for 100-pin LCC package 1 OSC-2 oscillator circuit board (bare-board) 1 Hardw
Résumé du contenu de la page N° 20
2.4 Name of Each Part (1) System Configuration Figure 2.1 System configuration (1) to (4) in Figure 2.1 are included in this product package. (1) Emulation pod (M30803T-RPD-E) This emulation pod contains an evaluation MCU, emulation memory and circuit to feature the debugging function. (2) Flexible cable (FLX120-RPD) This 120-pin flexible cable connects the PC4701 emulator and the emulation pod. (3) Flexible cable (FLX160) This 160-pin flexible cable connects the emulation pod and the target s
Résumé du contenu de la page N° 5
4.4 Self-check ...........................................................................................................53 (1) Self-check Procedure ...............................................................................53 (2) If an Error is Detected in the Self-check ..................................................53 Chapter 5. Specifications .....................................................................................................55 5.1 Specifications .................
Résumé du contenu de la page N° 6
MEMO ( 6 / 74 )
Résumé du contenu de la page N° 7
Chapter 1. Precautions for Safety This chapter describes precautions for using this product safely and properly. For precautions for the emulator main unit and the emulator debugger, refer to each user's manual included with your product. 1.1 Safety Symbols and Meanings ..................................................................................................... 8 WARNING Warning for Installation ...........................................................................................
Résumé du contenu de la page N° 8
Chapter 1. Precautions for Safety In both the user's manual and on the product itself, several icons are used to insure proper handling of this product and also to prevent injuries to you or other persons, or damage to your properties. This chapter describes the precautions which should be taken in order to use this product safely and properly. Be sure to read this chapter before using this product. 1.1 Safety Symbols and Meanings If the requirements shown in the "WARNING" sentences are ignored,
Résumé du contenu de la page N° 9
WARNING Warning for Installation: • Do not set this product in water or areas of high humidity. Make sure that the main unit does not get wet. Spilling water or some other liquid into the main unit can cause an unrepairable damage. Warnings for Use Environment: • The emulation pod is air-cooled with the ventilation slot. Therefore, do not block the ventilation slot. When heated to high temperatures, the emulation pod may not work properly. • This equipment is to be used in an environment with a
Résumé du contenu de la page N° 10
IMPORTANT Notes on Downloading Firmware: • Before using this product for the first time, it is necessary to download the dedicated firmware (control software for the emulation pod built into the PC4701). Please note that, to do this, it is necessary to start up the PC4701 in maintenance mode. For firmware download procedures, see "4.2 Downloading Firmware" (page 48). Once the firmware has been downloaded, the product can be used by simply turning on the power. • Do not shut off the power while d
