Résumé du contenu de la page N° 1
Perle PoE/PoE+
10/100/1000 Ethernet
Media Converters
Installation Guide
S-1110P
S-1110PP
S-1110DP
S-1110DPP
P/N 5500317-11
Résumé du contenu de la page N° 2
Overview This document contains instructions necessary for the installation and operation of the Perle Standalone PoE/PoE+ 10/100/1000 rate converting Media Converters (S-1110P). These products have the ability to convert 10/100/1000Base-T cable connections (copper) to 100/1000Base-X connections (fiber). The Perle media converters function as a PoE switch, and support a variety of port configurations, including single or dual UTP and fiber ports. These media converters function as Power
Résumé du contenu de la page N° 3
PoE (P) Connector Mode Wavelength PoE+ (PP) (xx) Distance (TX/RX) S-1110P-S1SC80U SM SC 1510/1590 nm S-1110PP-S1SC80U 80 km/50 mi. S-1110P-S1SC80D SM SC 1590/1510 nm S-1110PP-S1SC80D 80 km/50 mi. S-1110P-S2xx120 SM SC/ST 1550 nm S-1110PP-S2xx120 120 km/74.6 mi. S-1110P-S1SC120U SM SC 1510/1590 nm S-1110PP-S1SC120U 120 km/74.6 mi. S-1110P-S1SC120D SM SC 1590/1510 nm S-1110PP-S1SC120D 120 km/74.6 mi. S-1110P-S2xx160 SM SC/ST 1550 nm S-1110PP-S2xx160 160 km/100 mi. S-1110P-SF
Résumé du contenu de la page N° 4
Dual Copper / PoE (DP) Connector Mode Wavelength Dual Copper / PoE+ (DPP) (xx) Distance (TX/RX) S-1110DP-S1SC80D SM SC 1590/1510 nm S-1110DPP-S1SC80D 80 km/50 mi. S-1110DP-S2xx120 SM SC/ST 1550 nm S-1110DPP-S2xx120 120 km/74.6 mi. S-1110DDP-S1SC120U SM SC 1510/1590 nm S-1110DDPP-S1SC120U 120 km/74.6 mi. S-1110DP-S1SC120D SM SC 1590/1510 nm S-1110DPP-S1SC120D 120 km/74.6 mi. S-1110DP-S2xx160 SM SC/ST 1550 nm S-1110DPP-S2xx160 160 km/100 mi. S-1110DP-SFP SFP Note 1 S-1110
Résumé du contenu de la page N° 5
Installation The default DIP switch settings (all switches in the UP position) will work for most installations. These are the steps required to configure the Perle S-1110P Ethernet media converter: 1. Insert SFP Module (SFP Model only). 2. Set the Auto-MDIX jumper setting (optional). 3. Set the DIP switch settings (if required). 4. Set the Powering Option Jumpers (if required). 5. Install and connect the fiber cable(s). 6. Install and connect the copper cable(s). 7. Power up the m
Résumé du contenu de la page N° 6
Power Sourcing Pinouts Note: The factory settings for Power Sourcing Pinouts will work for most installations as 802.3a and 802at-2009 ( POE/POE+) devices will detect and sync to the correct POE option. However, in the rare case that you need to modify the settings, the procedure is below. When Power Sourcing is enabled on a copper port, the S-1110P will provide power to the connected PD device over the Ethernet cable (see PSE function on Dip Switch configurations). The wire pairs on th
Résumé du contenu de la page N° 7
Powering Options Jumper Settings In order to select a powering option, the Power Options Jumper settings must be set. Each copper port has a set of Power Option jumpers. To access the Powering Options Jumper settings, unscrew the six side screws on the case and remove the cover plate. Locate the Power Option jumper set and strap the option pins as detailed below. Perle PoE/PoE+ 10/100/1000 Ethernet Media Converter 7 Installation Guide
Résumé du contenu de la page N° 8
DIP Switches The DIP switches are accessible through the opening in the side of the enclosure. Bank 1 Bank 2 Bank 1 Bank 2 Note: All switch changes take effect immediately. Switch changes will cycle power to the PD only if the PD Reset switch is set to On or you make changes to the PSE Power switches. 8 Perle PoE/PoE+ 10/100/1000 Ethernet Media Converter Installation Guide
Résumé du contenu de la page N° 9
DIP Switch Settings Bank 1 Auto Negotiation copper (Switch 1) Switch Position Copper 1 Copper 2 Up (default) Auto Auto Down Off Auto Note: Auto negotiation should only be turned off, if the copper link partner does not support Auto Negotiation and fixed settings are required by the copper link partner. Auto: When enabled, the media converter will negotiate with its link partner to determine the most optimal parameters for this connection. The S-1110P will advertise capabilities of 10,
Résumé du contenu de la page N° 10
of link on either the fiber or copper port can occur without affecting the other connection. Smart Link Pass-Through In this mode, the link state on one connection is directly reflected through the media converter to the other connection. If link is lost on one of the connections, then the other link will be brought down by the media converter. If the media converter has 2 copper or 2 fiber connections, then both must go down in order to affect the other connection(s). If the installati
Résumé du contenu de la page N° 11
Illustration of the FFA The following diagram is an illustration of the operation of this feature. (A) – Remote Media Converter setup for Fiber Fault Alert Enabled, Fiber Negotiation – OFF and Link Mode – Standard. (B) – Local Media Converter setup for Fiber Fault Alert Enabled, Smart Link Pass-Through On and Fiber Negotiation - OFF 1 – (A) Loses fiber connection on its receiver. 2 – (A) Sends FFA. 3 – (B) Detects FFA signal and shuts down the fiber link. 4 – (B) Drops link on copper
Résumé du contenu de la page N° 12
Speed copper (Switch 5) Switch Position Copper port 1 Copper port 2 Up (default) 100 NA Down 10 NA Note When Auto Negotiation (SW1) is set to Off, the media converter will use this switch setting for copper port 1 speed. 100: When Switch 5 is in the Up position, the S-1110P will force the speed to 100 Mbps. 10: When Switch 5 is in the Down position the media converter will force the speed to 10 Mbps. Auto Fiber Negotiation (Switch 6) Switch Fiber 1 Fiber 2 Position 1000 Mbps 1000 M
Résumé du contenu de la page N° 13
Full Duplex: The Media Converter Module will be set to Full Duplex mode on its fiber link. Half Duplex: The Media Converter Module will be set to Half Duplex mode on its fiber link. Loopback Fiber-1 (Switch 7) Loopback Fiber-2 (Switch 8) Switch Position Mode Up (default) Disabled Down Enabled Disabled: The loopback feature is disabled. This is default position for normal operation. The switch must be set to this position in order for data to pass through the media converter. Enabled:
Résumé du contenu de la page N° 14
Down Down PSE disabled These switches must be set in order to enable the power sourcing function and to indicate the type of device detection required. If the device type is unknown, the default should be used as per IEEE802.3af/at standards. Enabled: When enabled, the media converter will perform Power Sourcing Equipment (PSE) functions as per IEEE802.3af (POE) or 802.3at-2009 (POE+) standards. Disabled: When disabled the media converter will not perform PSE functions. PD Power Reset
Résumé du contenu de la page N° 15
Fiber Redundancy (Switch 7) Dual fiber models only Switch Position Mode Up (default) Disabled Down Enabled Disabled: When this feature is disabled, both fiber ports will operate as independent ports on a switch. Normal switch rules and functions will apply. Enabled: When this feature is enabled, fiber port 1 will be the primary active fiber connection port and fiber port 2 will be in standby and in an inactive state. Should a loss of link occur on fiber port 1, fiber port 2 will be a
Résumé du contenu de la page N° 16
Installing the SFP Fiber Module SFP models only. 1. Locate the appropriate fiber module and insert the SFP into the opening on the front of the media converter. 2. Ensure the SFP module is properly seated. The release latch of the SPF fiber transceiver must be in the closed (up) position before insertion. 3. The SFP module may be inserted before or after applying power to the media converter. 4. Proceed with cable connections. Installing the Duplex Fiber Cable 1. Locate a 1000Base-X
Résumé du contenu de la page N° 17
Installing the Copper Cable 1. Locate 10/100/1000Base-T compliant copper cables with the appropriate connectors. 2. Connect the RJ-45 cable between the Perle media converter and the device. Note: The Perle media converter supports Auto-MDIX which allows connection of a straight-through or cross-over Ethernet cable. See Auto-MDIX Jumper Settings in this guide for jumper positions. Grounding the Media Converter If your installation requires additional grounding the following procedure
Résumé du contenu de la page N° 18
2. Attach the grounding lug to the chassis and secure with the grounding screw(s). Attaching the Power cord strain relief clip 1. Feed the power cord through the opening in the power cord relief clip. 2. Attach the power cord relief clip to the chassis and secure with the provided screw. 3. Plug the power cord into the AC power connector at the rear of the chassis. 4. Plug the other end of the power cord into an appropriate power outlet. Powering up the Perle Media Converter 1. Co
Résumé du contenu de la page N° 19
Operation Status LED The Perle PoE/PoE+10/100/1000 Rate converting Media converters have status LEDs located on the front panel of the unit. PWR On – Power is applied to the unit Blinking (slow) – Loopback mode (one or both fiber interfaces are in loopback mode) Blinking (fast) Power On failure. See LED Pattern to determine pattern combination and failure cause LED Pattern FDF LKF FDC PSE Off Off On On SFP incompatible Internal hardware All other LED patterns failure FD
Résumé du contenu de la page N° 20
SPD-(Copper Port 1/2) Green – 1000 Mbps Orange – 100 Mbps Off – 10 Mbps (if link is currently established) FDC-1/2 (Duplex on Copper 1/2) On – Full Duplex Mode Off – Half Duplex Mode LKC-1/2 (Link Status on Copper port 1/2) On – Copper link is present Off – No copper link present Blinking (slow) – Copper link appears functional – Copper link has been brought down by Smart Link Pass-Through. Blinking (fast) – Copper link up and receiving data PSE-1/2 Solid Green (Active) – The PS
