Résumé du contenu de la page N° 1
®
Hotwire Shelf Concentration and Processing (SCP) Card
Installation Instructions
Document Number 8400-A2-GZ40-10
October 2003
Hotwire Shelf Concentration and Processing Card
®
A Hotwire Shelf Concentration and Processing (SCP) card is a circuit card
assembly that comprises a parent card with an ATM switch, a backplane interface,
a processor, a cell multiplexer/demultiplexer, and an uplink childcard. The
childcard determines the type of ATM uplink supported by the SCP card.
When the SCP card
Résumé du contenu de la page N° 2
Product Documentation Online Complete documentation for this product is available at www.paradyne.com. Select Support → Technical Manuals → Hotwire DSL Systems. Select the following documents: 8400-A2-GB20 Hotwire Shelf Concentration and Processing (SCP) Card User’s Guide 8620-A2-GN20 Hotwire 8620 GranDSLAM Installation Guide 8820-A2-GN20 Hotwire 8820 GranDSLAM Installation Guide 8900-A2-GB20 Hotwire ATM Line Cards, Models 8955, 8965, and 8985, User’s Guide To order a paper copy of a Paradyne d
Résumé du contenu de la page N° 3
SYSTEM OK Alm Test ETHERNET TX RX Coll DSL PORT 1 2 3 4 SYSTEM OK Alm Test ETHERNET TX RX Coll T Te T o SYS EM OK Alm st ETHERNET X RX C ll POWER ALARMS A B Fan Major Minor CLOCK SERIAL AC LAN/WAN SLOT A MCC ALARM 2 4 6 8 A 10 12 14 16 18 B SERIAL ALARM 1 3 5 7 9 B 11 13 15 17 CLOCK SMCM POWER ENTRY MODULE POWER ENTRY MODULE LEFT UNIT: LINE A LEFT UNIT: LINE A RIGHT UNIT: LINE B RIGHT UNIT: LINE B WARNING! POWER MUST BE DISCONNECTED AT THE SOURCE WARNING! POWER MUST BE DISCONNECTED AT THE SOURC
Résumé du contenu de la page N° 4
Installing Two SCP Cards in the Same DSLAM Two SCP cards may be installed in one DSLAM to provide redundancy or load sharing. There are three basic configurations for paired SCP cards: Y-Cable – The OC3 ports of the two SCP cards are connected to the same uplink device. If the active SCP card fails, the backup SCP card automatically becomes the uplink. See Equipment List on page 15 for available Y-cables. Dual Link – Automatic switching occurs in the event of failure, but the SCP cards
Résumé du contenu de la page N° 5
SYSTEM Active Standby Alarm Test ETHERNET TX RX UPLINK LK 1 DS3 Uplink SCP cards with a DS3 uplink have two BNC jacks: one for the transmit direction and one for the receive direction. To cable an SCP card with an DS3 uplink: 1. Connect the input cable to the RX jack on the faceplate of the SCP card. 2. Connect the output cable to the TX jack on the faceplate of the SCP card. 3. If the chassis is mounted in a rack, direct the cables toward the nearest rail and fasten them with cable ties. 03-
Résumé du contenu de la page N° 6
SYSTEM Active Standby Alarm Test ETHERNET TX RX UPLINK LK 1 OC3 Uplink SCP cards with an OC3 uplink use an SFP transceiver that accepts an LC-type connector. To cable an SCP card with an OC3 uplink: 1. Remove the plastic dustcover from the SFP socket. 2. Insert the LC connector of your fiber optic cable into the SFP socket. 3. Observing the minimum bend radius for your cable, fasten it with cable ties in such a way that it will not be kinked or snagged in the course of other cabling. If you d
Résumé du contenu de la page N° 7
SYSTEM Active Standby Alarm Test ETHERNET TX RX UPLINK LK5 LK1 LK6 LK2 LK7 LK3 LK8 LK4 IMA Uplink SCP cards with an IMA uplink have an RJ45M-type 50-position connector with eight Tip/Ring and eight Tip1/Ring1 connections that conforms to ANSI T1.403-1999. The following splitter cables are available: Feature Number 8026-F1-001 for the Model 8416 SCP card terminates in eight 8-pin modular jacks. See Table 2, Feature Number 8026-F1-001 Pin Assignments, on page 12. To connect the SCP card to a
Résumé du contenu de la page N° 8
SYSTEM Active Standby Alarm Test SYSTEM Active ETHERNET Standby TX Alarm RX Test ETHERNET TX UPLINK RX LK 1 UPLINK LK 1 SYSTEM Active Standby Alarm Test ETHERNET TX RX UPLINK LK5 LK1 LK6 LK2 LK7 LK3 LK8 LK4 SCP Card LEDs The following table describes the meaning and states of the LEDs on the Hotwire SCP card faceplate. Example faceplates are shown at left. Type LED LED is . . . Indicating . . . SYSTEM Active Green, This SCP card is the active card Slow-cycling and is functioning normally. Slo
Résumé du contenu de la page N° 9
Using the Default Management Address The SCP card uses Transaction Language 1 (TL1) language for Command Line Interface (CLI) commands and messages. The CLI can be used to configure and maintain the system, but the web interface is recommended. You can access the web interface using the default management address or a network address you specify using the CLI (see Setting the Management Address Using the CLI). Procedure To use the default management address: 1. Connect a PC to the Ethernet p
Résumé du contenu de la page N° 10
Setting the Management Address Using the CLI The management address can be set using the CLI. Procedure To set the management address of the SCP card using the CLI: 1. Using the supplied cable and DB9 adapter, connect a PC with a terminal emulation program to the SERIAL SCM jack of your GranDSLAM. This gives you access to the CLI. 2. Log in to the SCP card using the ACT-USER command: ACT-USER::SUPERUSER:::ASN#1500 The default password, ASN#1500, will appear as asterisks on your screen. 3. Assi
Résumé du contenu de la page N° 11
Using the Web Interface To access the web interface: Procedure 1. Open your web browser. (Internet Explorer Version 6 or above is recommended.) 2. Type http:// and the IP address of the SCP card into the Address field of your browser window. This is 10.10.10.10 by default, or the address you set using the CLI. For example: 3. A login window appears. Enter the default User ID (SUPERUSER) and Password (ASN#1500), and click on OK. The web interface screen appears. 4. Click on the menu tab appro
Résumé du contenu de la page N° 12
BNC Jacks The following table shows the connections for BNC jacks (Model 8411). Table 1. BNC Jack Connections Connector Label Connection Description Transmit TX Pin Transmit signal Shell Transmit signal return Receive RX Pin Receive signal Shell Receive signal return IMA Interface Pin Assignments Table 2 lists connector pin assignments for Model 8416, and the Model 8417 when used with modular connectors for a 120-ohm E1 connection. Table 3 lists connector pin assignments for the Model 8417 whe
Résumé du contenu de la page N° 13
Table 2. Feature Number 8026-F1-001 Pin Assignments (2 of 2) 8026-F1-001 DS1 or 120 Ohm 50-Position Telco RJ48C Connector E1 Port Connector Pinouts Pinouts Function Port 5 39 5 Data Out (Tip) 14 4 Data Out (Ring) 38 2 Data In (Tip) 13 1 Data In (Ring) Port 6 42 5 Data Out (Tip) 17 4 Data Out (Ring) 41 2 Data In (Tip) 16 1 Data In (Ring) Port 7 45 5 Data Out (Tip) 20 4 Data Out (Ring) 44 2 Data In (Tip) 19 1 Data In (Ring) Port 8 48 5 Data Out (Tip) 23 4 Data Out (Ring) 47 2 Data In (Tip) 22 1 D
Résumé du contenu de la page N° 14
Table 3. Feature Number 8027-F1-001 Pin Assignments (2 of 2) 50-Position Telco 75 Ohm E1 Port Function Connector Pinouts BNC Connector Port 3 Data In 7 Shell (Ring) 32 Pin (Tip) Data Out 8 Shell (Ring) 33 Pin (Tip) Port 4 Data In 10 Shell (Ring) 35 Pin (Tip) Data Out 11 Shell (Ring) 36 Pin (Tip) Port 5 Data In 13 Shell (Ring) 38 Pin (Tip) Data Out 14 Shell (Ring) 39 Pin (Tip) Port 6 Data In 16 Shell (Ring) 41 Pin (Tip) Data Out 17 Shell (Ring) 42 Pin (Tip) Port 7 Data In 19 Shell (Ring) 44 Pin
Résumé du contenu de la page N° 15
Equipment List The following feature numbers may be used to order SCP cards, line cards, and related cables. Table 4. Feature Numbers Description Feature Number Cards SCP Card: DS3 8411-A1-000 SCP Card: OC3/STM1 Multimode Fiber 8412-A1-000 SCP Card: OC3/STM1 Single Mode Fiber Intermediate Reach 8413-A1-000 SCP Card: OC3/STM1 Single Mode Fiber Long Reach 8414-A1-000 SCP Card: 8-Port DS1 IMA 8416-A1-000 SCP Card: 8-Port E1 IMA 8417-A1-000 MCP GranDSLAM 3.0 8900-B1-211 ADSL2 ATM Line Card 24 port
Résumé du contenu de la page N° 16
SCP Card Technical Specifications Table 5. SCP Card Technical Specifications (1 of 2) Specifications Criteria Size Length: 10.4 inches (26.42 cm) Height: 11.15 inches (28.32 cm) Width: 1.0 inches (2.54 cm) Weight Approximately 1.7 lbs. (0.76 kg) Approvals Safety Certifications Refer to the equipment’s label for approvals on product. Power The SCP card contains a DC-to-DC converter that requires 48V power input. The 48V power is distributed through the Hotwire chassis backplane. Power Dissipati
Résumé du contenu de la page N° 17
Table 5. SCP Card Technical Specifications (2 of 2) Specifications Criteria OC3 Uplink Specifications Number of ports 1 OC3 Connector Type Duplex LC Socket Standards Supported ANSI T1.105.06-94 Jitter, ANSI T1.105.09 94 Jitter, ANSI T1.117.06-91, ITU-T G.957 7/95 Frame Formats OC3 or STM-1 Operation, Direct Mode only Line Type Non-Return to Zero Data Rates Supported 155.52 Mbps Facility Datalink Protocol ANSI T1.105 Format, ANSI T1.646 HEC, ITU-T I.432 Scrambler Cable Distance Model 8412 (MMF)
Résumé du contenu de la page N° 18
Warranty, Sales, Service, and Training Information Contact your local sales representative, service representative, or distributor directly for any help needed. For additional information concerning warranty, sales, service, repair, installation, documentation, training, distributor locations, or Paradyne worldwide office locations, use one of the following methods: Internet: Visit the Paradyne World Wide Web site at www.paradyne.com. (Be sure to register your warranty at www.paradyne.com
