Résumé du contenu de la page N° 1
MIC-3321
3U CompactPCI Pentium M
760 2.0G High-performance
Controller
User Manual
Résumé du contenu de la page N° 2
Copyright Notice This document is copyrighted, 2004. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable. However, the original manufacture
Résumé du contenu de la page N° 3
Product Warranty Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech, or which have been subject to misuse, abuse, accident or improper instal- lation. Advantech assumes no liability under the terms of this warranty as a consequen
Résumé du contenu de la page N° 4
Technical Support and Assistance Step 1. Visit the Advantech web site at www.advantech.com/support where you can find the latest information about the product. Step 2. Contact your distributor, sales representative, or Advantech's cus- tomer service center for technical support if you need additional assistance. Please have the following information ready before you call: - Product name and serial number - Description of your peripheral attachments - Description of your software (operating
Résumé du contenu de la page N° 5
Contents Chapter 1 Hardware Configuration ................................ 2 1.1 Introduction ....................................................................... 2 1.2 Specifications .................................................................... 3 1.2.1 Standard SBC Functions ................................................ 3 1.2.2 Display ...........................................................................4 1.2.3 Mechanical and Environmental Specifications .............. 4 1.3
Résumé du contenu de la page N° 6
4.2.5 PNP/PCI Configuration Setup ..................................... 29 Figure 4.6:PNP/PCI configuration screen ................... 29 4.2.6 PC Health Status .......................................................... 30 Figure 4.7:PC Health Status setup screen .................... 31 4.2.7 Spread Spectrum Control ............................................ 32 Figure 4.8:PC Health Status setup screen .................... 32 4.2.8 Load Optimized Defaults .......................................
Résumé du contenu de la page N° 7
22 1 Hardware Configuration CHAPTER
Résumé du contenu de la page N° 8
Chapter 1 Hardware Configuration 1.1 Introduction MIC-3321 is a 3U, all-in-one, controller board, compliant with PICMG 2.0 R2.1 CompactPCI specifications. For high computing performance, MIC-3321 uses an Intel Pentium M 760 2.0GHz CPU and Intel 915GM chipset. This CPU provides high performance with its on-chip 2 MB L2 cache and is delivered in a Micro-FCBGA 479 package. MIC-3321 offers powerful functions on a 3U-sized board for perfor- mance-demanding applications like real-time machi
Résumé du contenu de la page N° 9
1.2 Specifications 1.2.1 Standard SBC Functions • CPU: MIC-3321 supports Intel Pentium M 2.0 GHz • Optional: Celeron M 1.0GHz/ Celeron M 800MHz (non cache) • BIOS: Award 4 Mb flash memory • Chipset: Intel 915GM Graphics and Memory Controller Hub (GMCH) Intel 82801FBM I/O Controller Hub (ICH6M) • System Memory: Directed Soldered 512MB DDR2 533 SDRAM (MIC-3321/3321S) Directed Soldered 512MB DDR2 400 SDRAM (MIC-3321C/3321CS) Directed Soldered 256MB DDR2 400 SDRAM (MIC-3321LS)
Résumé du contenu de la page N° 10
1.2.2 Display • Controller: Intel Graphics Media Accelerator 900 • VRAM: DVMT3.0 128MB • Resolution: Up to 2048x1536 with 32-bit color at 75Hz 1.2.3 Mechanical and Environmental Specifications • Board Size (W x H) : 160 x 100 mm (3U) • Operating Temperature:0 ~ 50° C (MIC-3321 Pentium M 2.0GHz) 0~50° C (MIC-3321LS Celeron M 800MHz) -25 ~ 70° C (MIC-3321C Celeron M 1.0G) • Storage Temperature: -40 ~ 80° C • Board Weight: 0.6 kg 1.3 Function Block Diagram Figure 1.1: MIC-3321 Function
Résumé du contenu de la page N° 11
1.4 Board Dimensions 160 mm 100 mm Figure 1.2: MIC-3321 Board Dimensions 1.5 Dip Switch Settings Since MIC-3321 is composed of one main board and one daughter board, for ease of understanding and a convenient naming, we will use 1F (1st level) to represent the main board, and 2F (2nd level) to represent the daughter board hereafter in this manual. Before setting the switches, you need to disassemble the MIC-3321 to 1F and 2F as in Figures 1.3 and 1.4. 5 Chapter 1
Résumé du contenu de la page N° 12
1.5.1 Switch Locations Table 1.1 lists the switch functions of MIC-3321 (be sure that the switch is white one). Figure 1.3 and Figure 1.4 show the locations of S1 and S2, respectively. Table 1.1: MIC-3321 Switch Descriptions DIP-SW Mode Setting Function 1F-S1 Mode Bit-1 : ON LAN1 on Rear I/O Bit-2 : OFF CF : Slave Bit-1 : OFF LAN1 on Front I/O Bit-2 : ON CF : Master 2F-S2 Mode Bit-1 : ON LAN2 on Rear I/O Bit-2 : OFF N/C Bit-1 : OFF LAN2 on Front I/O Bit-2 : ON N/C Figure 1.3: MIC-3321 S1 Locat
Résumé du contenu de la page N° 13
Figure 1.4: MIC-3321 S2 Location (2F) 1.6 Safety Precautions Follow these simple precautions to protect yourself and the products. 1. To avoid electrical shock, always disconnect the power from your PC chassis before you work on it. Don't touch any components on the CPU card or other cards while the PC is on. 2. Disconnect power before making any configuration changes. The sudden rush of power as you adjust a switch or install a card may damage sensitive electronic components. 3. Always g
Résumé du contenu de la page N° 14
MIC-3321 User Manual 8
Résumé du contenu de la page N° 15
22 2 Connecting Peripherals CHAPTER
Résumé du contenu de la page N° 16
Chapter 2 Connecting Peripherals 2.1 Connectors Figure 2.1 and 2.2 show MIC-3321 connector locations. Figure 2.3 shows MIC-3521 connector location. Figure 2.1: MIC-3321 Connector Locations (1F) Figure 2.2: MIC-3321 Connector Locations (2F) MIC-3321 User Manual 10
Résumé du contenu de la page N° 17
Figure 2.3: MIC-3521 Connectors 11 Chapter 2
Résumé du contenu de la page N° 18
Table 2.1: MIC-3321 Connectors Overview Number Function Description 1F-CN1 USB1 USB1 Type-A Female on Front side panel. 1F-CN3 USB2 USB2 Type-A Female on Front side panel. 1F-CN2 CF CompactFlash socket 1F-CN5 VGA D-Sub 15-pin (Female) on Front side panel. 1F-RJ1 LAN1 10/100/1000Base-TX Ethernet on Front side panel. 1F-S1 LAN1 MODE, Bit-1 Setting: LAN1 Front I/O or Rear I/O CF MODE Bit-2 Setting: CF master or slave mode 2F-CN7 COM1 Serial port: RS-232 on Front I/O 2F-CN8 PS2 Standard Mini-DIN 6-
Résumé du contenu de la page N° 19
2.2 Card Installation The CompactPCI connectors are firm and rigid, but require careful han- dling while plugging and unplugging. Improper installation of a card can easily damage the backplane of the chassis. The inject/eject handle of MIC-3321 helps you install and remove the card easily and safely. Follow the procedure below to install the MIC- 3321 into a chassis: To install a card: 1. Hold the card vertically. Be sure that the card is pointing in the cor- rect direction. The componen
Résumé du contenu de la page N° 20
To remove a card: 1. Unscrew the four screws on the front panel. 2. Press the lower handle down to release the card from the backplane. 3. Slide the card out. Figure 2.4: Chassis Installation/Removal MIC-3321 User Manual 14
