Résumé du contenu de la page N° 1
802.11g Wireless USB Adapter
Model # AWLL3028
User’s Manual
Rev. 1.1
Résumé du contenu de la page N° 2
Table of Contents 1. Introduction................................................................................................................................. 3 1.1 Package Contents.................................................................................................................. 3 1.2 Features................................................................................................................................. 3 2. Installation.................................
Résumé du contenu de la page N° 3
1. Introduction Thank you for purchasing the 802.11g Wireless USB Adapter. This USB Adapter is designed to comply with IEEE 802.11g Wireless LAN standard and is suitable for notebook computers or desktop computers with a USB 2.0 port. This Adapter supports WiFi Protected Access (WPA2-PSK and WPA-PSK) data encryption for higher security that protects your wireless network from eavesdropping. Client users are required to authorize before accessing the APs or AP Routers, and the data tr
Résumé du contenu de la page N° 4
2. Installation 2.1 Install Driver & Utility This section provides instructions on how to install the Wireless USB Adapter. The driver is installed along with the utility. Insert the USB adapter into an available USB port and turn on your computer. Windows 2000/XP Users: After turning on the computer, Windows will launch the Found New Hardware Wizard. The Found New Hardware Wizard appears differently depending on your operating system. Click Cancel to quit the wizard and
Résumé du contenu de la page N° 5
Once you see this message, continue to Step 1. Step 1 The Autorun screen will pop up. Select Install Utility and Driver from the menu. Note: If the Autorun screen doesn’t appear automatically, or if you get a blank white screen, go to Start, Run, and type D:\Utility\Setup.exe (where D is the letter of your CD drive) and click OK. Windows Vista Users: At this point, you may get a warning message like the one below. Make sure that you click Allow to continue with the instal
Résumé du contenu de la page N° 6
Step 2 Click Next at the welcome screen. 6
Résumé du contenu de la page N° 7
Windows 2000/XP Users: Click Continue Anyway at the Windows Logo Screen. (For Windows 2000, click Yes at the Digital Signature Not Found prompt). Windows Vista Users: When the Windows Security box appears click Install this driver software anyway. Step 3 Click Finish to complete the installation. 7
Résumé du contenu de la page N° 8
2.2 Verify Driver Installation To verify if the driver has been installed successfully, please perform the following steps. Step 1 Right-click on My Computer from your desktop and select Properties. Step 2 If you are using Windows XP/2000 select the Hardware tab, then click on Device Manager. 8
Résumé du contenu de la page N° 9
If you are using Windows Vista, click on the device manager link on the left side of the screen. 9
Résumé du contenu de la page N° 10
Step 3 Click the “+” next to Network adapters from the list and verify that AirLink101 802.11g Wireless USB Adapter is listed and no yellow question mark is beside it. If AirLink101 802.11g Wireless USB Adapter is not listed, or you see a yellow question mark beside it, you will need to reinstall the driver. 10
Résumé du contenu de la page N° 11
3. Configuring the Adapter 3.1 Windows 2000/XP Configuration This section describes how to connect your wireless adapter to a wireless network. Note to Windows XP Users: You must disable the Wireless Zero Configuration Utility in order to use the bundled Wireless Utility. Please follow the steps below to disable XP’s wireless utility. Double-click on the Wireless Network Connection Icon in the system tray and then click on Properties or Advanced. When the new wireless ne
Résumé du contenu de la page N° 12
If there is no Wireless Networks tab, skip ahead to Step 1 Step 1 To open the utility, double click on the Wireless Configuration Utility icon in the system tray at the bottom right-hand corner of your screen. Step 2 Go to the Available Network tab, select the SSID (Network Name) of the wireless network you wish to connect to, and click Add to Profile. 12
Résumé du contenu de la page N° 13
If the network you are attempting to connect to does not have encryption enabled, you will see the following box pop up on your screen: Click OK to connect. If the network you are attempting to connect to is configured for encryption, the following window will appear: 13
Résumé du contenu de la page N° 14
Enter the encryption settings for your router in the appropriate boxes and click OK to connect. Step 3 You should now be connected. Click on the general tab to check the status of your connection. It should say Associated next to status, and there should be green bars next to Signal Strength and Link Quality. 14
Résumé du contenu de la page N° 15
15
Résumé du contenu de la page N° 16
3.2 Windows Vista Configuration Windows Vista has its own built in utility, so the AirLink101 Wireless Configuration Utility is not used. To connect to a network using the Windows Vista utility, right click on the networking icon down in the bottom right hand corner. Then click on Connect to a network. Select your network from the list and click Connect. 16
Résumé du contenu de la page N° 17
If the network you are connecting to does not have encryption enabled, you will see the following warning: Click Connect Anyway to connect to the network. If the network you are attempting to connect to has encryption enabled, a box will appear asking you to enter your encryption key. 17
Résumé du contenu de la page N° 18
Enter your encryption key into the box and click Connect to establish a connection. If you do not know what your encryption key is, contact your router manufacturer for assistance. You should now be connected to your network. To save the connection settings so that you don’t have to go through the connection setup process each time you start your computer, check the boxes for Save this network and Start this connection automatically, then click Close to complete the setup. 3.3
Résumé du contenu de la page N° 19
restart the wireless computer before trying to connect again. Keep going through the channels until you find one that gives you a stable connection. For instructions on changing channels, refer to the documentation that came with your router. 19
Résumé du contenu de la page N° 20
4. Wireless Configuration Utility This section describes the various functions of the Wireless Configuration Utility that you can configure, including the settings of wireless encryption. 4.1 General The General tab provides you with the status of the current connection, including signal, network name (SSID), IP Address and router channel. At the bottom you have a few options for controlling the utility and adapter. Show Tray Icon allows you to show or hide the tray icon for t
