Résumé du contenu de la page N° 1
Agilent N1022A
Active Probe Adapter
User Guide
Résumé du contenu de la page N° 2
Notices © Agilent Technologies, Inc. 2003 Warranty Safety Notices The material contained in this document CAUTION No part of this manual may be repro- is provided “as is,” and is subject to being Caution denotes a hazard. It calls attention duced in any form or by any means changed, without notice, in future edi- to a procedure which, if not correctly per- (including electronic storage and tions. Further, to the maximum extent formed or adhered to, could result in retrieval or translation
Résumé du contenu de la page N° 3
Contents N1022A Active Probe Adapter 1 General Safety Considerations 2 Instrument Markings 3 Using the Probe Adapter 4 Inspecting the N1022A 4 Connecting the N1022A 5 Static-Safe Workstation 8 Reducing ESD Damage 9 Specifications and Regulatory Information 10 Specifications 10 Regulatory Information 13 Declaration of Conformity 14 Service 15 Checking Probe Power Outputs 15 Returning the N1022A 16 Agilent Technologies Service Offices 17 Contents 1
Résumé du contenu de la page N° 4
Contents Contents 2
Résumé du contenu de la page N° 5
N1022A Active Probe Adapter N1022A Active Probe Adapter The N1022A Active Probe Adapter provides the interface to connect an Agilent Infiniimax Active Probe to an Agilent 86100-series Infiniium DCA. To use the N1022A requires that firmware revision A.03.05 or later be installed on the Infiniium DCA. The Infiniimax Active Probes include the following: 1131A, 1132A, and 1134A. Other supported active probes include the 1152A, 1156A, 1157A, and 1158A. CAUTION When using the N1022A, always work at
Résumé du contenu de la page N° 6
General Safety Considerations General Safety Considerations This product has been designed and tested in accordance with the standards listed in the Manufacturer’s Declaration of Conformity, and has been supplied in a safe condition. The product documentation contains information and warnings which must be followed by the user to ensure safe operation and to maintain the product in a safe condition. Before using this product, review the safety information for cautions and warnings. Use this
Résumé du contenu de la page N° 7
Instrument Markings Instrument Markings The instruction manual symbol. The product is marked with this warning symbol when it is necessary for the user to refer to the instructions in the manual. The laser radiation symbol. This warning symbol is marked on prod- ucts which have a laser output. The AC symbol is used to indicate the required nature of the line module input power. The Standby symbol is used to mark the position of the instrument power line switch. The CE mark is a registered tr
Résumé du contenu de la page N° 8
Using the Probe Adapter Using the Probe Adapter There are a few things to consider when connecting the N1022A Active Probe Adapter to an active probe and the Infiniium DCA. The dynamic range of the system will be 3.2 V (6.4 Vp-p), which with probe off- set, covers most digital technologies. The Infiniium DCA provides both power and offset control to the active probe adapter through the plug-in module front panel connector. Probe offset is changed by adjusting the vertical offset contro
Résumé du contenu de la page N° 9
Connecting the N1022A Technologies sales office. If the shipping container is damaged, or the cushioning materials show signs of stress, notify the carrier as well as your Agilent Technologies sales office. Keep the shipping materials for the carrier's inspection. The Agilent office will arrange for replacement of the N1022A at Agilent’s option without waiting for claim settlement. Connecting the N1022A CAUTION When using the N1022A, always work at a static-safe work station and wear a
Résumé du contenu de la page N° 10
Connecting the N1022A panel. Connecting to an Aux Power connector prevents the probe from being automatically calibrated. 3 Connect the probe output to the probe adapter input. The probe tip should not be connected to a device under test at this time. CAUTION The probe power cable connector automatically locks in the mating power connector. To separate the connection, you must pull on the knurled part of the cable connector housing. This releases the lock. If you pull directly on the power
Résumé du contenu de la page N° 11
Connecting the N1022A Figure 1. Probe Channel Dialog Box 6 Click Close. You can now change the probe tips or probe attenuation. You can also perform a probe calibration. You can access information about probe attenuation and probe calibration in the Infiniium DCA Help system. Using modules with 2.4 mm electrical input The N1022A can be directly connected to any 86100-series or 83480-series with a 3.5 mm electrical channel input. You can also connect the probe adapter to a module with 2.4 mm
Résumé du contenu de la page N° 12
Static-Safe Workstation Static-Safe Workstation Electrostatic discharge (ESD) can damage or destroy electronic components. All work on electronic assemblies should be performed at a static-safe work- station. The following figure shows an example of a static-safe work station using two types of ESD protection: Conductive table-mat and wrist-strap combination. Conductive floor-mat and heel-strap combination. Figure 2. Static Safe Workstation 8
Résumé du contenu de la page N° 13
Reducing ESD Damage Both types, when used together, provide a significant level of ESD protection. Of the two, only the table-mat and wrist-strap combination provides adequate ESD protection when used alone. To ensure user safety, the static-safe accessories must provide at least 1 MΩ of isolation from ground. Refer to Table 1 for information on ordering static-safe accessories. WARNING These techniques for a static-safe work station should not be used when working on circuitry with a vol
Résumé du contenu de la page N° 14
Specifications and Regulatory Information Specifications and Regulatory Information This section lists specifications and characteristics and regulatory information of the probe adapter. Specifications The distinction between specifications and characteristics is described as fol- lows: Specifications describe warranted performance over the temperature range 0°C to +55°C and relative humidity <95% (unless otherwise noted). All specifications apply after the temperature of the probe and the
Résumé du contenu de la page N° 15
Specifications Table 2. Environmental Specifications (2 of 2) Storage Humidity (type tested) 90% R.H. (non-condensing) at +65°C (+149°F), 24 hrs Shock (type tested) 30 g (half sine), 11 msec pulse Vibration (type tested) Random, 0.21g rms, 5 to 500 Hz, 10 minutes per axis Sine, 0.5g (0 to peak), 5 to 500 Hz, 1 octave/min Weight 200 g (7 oz) max Dimensions (excludes power cable) Height 34 mm (1.34 in.) Weight 38 mm (1.50 in.) Length 61 mm (2.4 in.) Power Cable Length 200 mm (7.9 in.) from conne
Résumé du contenu de la page N° 16
Specifications Table 3. Performance Specifications (2 of 2) Connector I/O (see figure below) DCA Connector Custom ruggedized 3.5 mm connector Probe Connector Precision BNC connector Power Connector Lemo push-pull 7-pin circular connector (works only with probe power) System Compatibility Compatible with Agilent 86100-series Infiniium DCA *Other Infiniium instruments in compliance with the Autoprobe interface can be added using the Probe dialog box located in the Infiniium graphical user in
Résumé du contenu de la page N° 17
Regulatory Information Regulatory Information Electrostatic Discharge Immunity - IEC 61000-4-2: 1995 passes criterion B. According to IEC 61000-4-2: 1995, system measurement may be affected when electrostatic discharges of 2 kV or more are applied to the outer sur- faces of the N1022A probe adapter when it is connected as part of a measure- ment system. Compliance with This ISM device complies with Canadian ICES-001. Canadian EMC Cet appareil ISM est conforme a la norme NMB du Canada. Requirem
Résumé du contenu de la page N° 18
Declaration of Conformity Declaration of Conformity 14
Résumé du contenu de la page N° 19
Service Service Service for the N1022A Active Probe Adapter is by replacement only. To order a new N1022A, contact your local Agilent Technologies Sales Office. Return the failed probe adapter to your local Agilent service center. If the probe adapter is still under warranty or is covered by an Agilent mainte- nance contract, it will be replaced under the terms of the warranty or con- tract. Refer to “Agilent Technologies Service Offices” on page 17 to contact the Agi- lent Call Center or you
Résumé du contenu de la page N° 20
Returning the N1022A Table 5. Probe Power Outputs Pin Supply Power Output 1+3V 2–3V 3Offset 4NC 5 and ring Probe ID 6NC 7R P 8–12V 9 +12V Returning the N1022A When the probe adapter is returned to an Agilent service office for servicing, it must be adequately packaged and have a complete description of the failure symptoms attached. Please notify the service office before returning your probe adapter for ser- vice. Any special arrangements for the adapter can be discussed at this time. This
