Instruction d'utilisation AC International UPP

Résumé du contenu de la page N° 1

Pocket Programmer Model UPP











UPB Pocket Programmer
User Guide

Résumé du contenu de la page N° 2

Pocket Programmer Model UPP DESCRIPTION IMPORTANT SAFETY INSTRUCTIONS The Pocket Programmer (model UPP) provides many of the features When using electrical products, basic safety precautions should of UPStart UPB configuration software in a portable hand held device. always be followed, including the following: The Pocket Programmer comes with a handy carrying case and AC power cord that plugs into any standard rec

Résumé du contenu de la page N° 3

Pocket Programmer Model UPP INSTALLATION The Pocket Programmer is designed for indoor use. Simply plug the appropriate end of the provided AC cord into the top of the UPP, the other end into any 120-volt outlet anywhere in the house. Once the Pocket Programmer completes its start up procedure the top two (of six) selections of the main menu are on the display and it is ready UP for use. MENU LEFT ENTER RIGHT R

Résumé du contenu de la page N° 4

Pocket Programmer Model UPP FUNCTION: Toggles the backlight on the LCD display. USING THE POCKET PROGRAMMER The pocket programmer mirrors the functionality of UPStart LED: The diagnostic LED operates Configuration software. If the installer is familiar with UPStart then just as the LED on the Computer most of the UPP menus and functions are intuitive and easy to use. If Interface Module. In Run CIM mode ther

Résumé du contenu de la page N° 5

Pocket Programmer Model UPP Access Network is used on an installed UPB network. It is useful when viewing or editing devices. Devices can be added or deleted. Links may also be added or deleted. The same functions are available in UPStart under the Device, Link and Network menus. 5

Résumé du contenu de la page N° 6

Pocket Programmer Model UPP New Network is used to create a UPB network by starting with a Network ID and 1 1)Access Network Password. The Network ID can be from 1 – 250. It is recommended to use a New Network 2)New Network different Network ID for each installation. The password is 4 hexidecimal characters, 0 – 9 and A – F. Once the UPB network is created devices and Links

may be added. Nothing is sto

Résumé du contenu de la page N° 7

Pocket Programmer Model UPP Add Device is used to add installed UPB devices to the UPB network. If a device is not found: 1. Make sure there is only one device in set up mode. 2. Check the wiring to ensure the connections are proper and the wire nuts are on tight. 3. Check the phase coupler to ensure it is properly installed and operational. 7

Résumé du contenu de la page N° 8

Pocket Programmer Model UPP Edit Device is used to change the settings on a previously added device. For instance, the dimming can be disabled under the Options sub-menu. - 8 -

Résumé du contenu de la page N° 9

Pocket Programmer Model UPP 9

Résumé du contenu de la page N° 10

Pocket Programmer Model UPP 10

Résumé du contenu de la page N° 11

Pocket Programmer Model UPP Edit Device Sub-Menu – Transmit Links 1 1)ID 2)Receive Links 1)ID 2)R 2 eceive Links 2)Receive Links 0 01)Link=241 02)Link=--- 08)Link=---

3 3)Transmit Links Super Toggler Super Toggler ... Super Toggler 3)Transmit Links 01)Link=241 01)Link=242 Field rolls over. 4 4)Options Super Toggler

Résumé du contenu de la page N° 12

Pocket Programmer Model UPP 12

Résumé du contenu de la page N° 13

Pocket Programmer Model UPP 1 1)ID 2)Receive Links Edit Device - Advanced 1)ID 2)Re 2 ceive Links 2)Receive Links 3 3)Transmit Links

1)X 1 mit Type: Transmit Type= Transmit Type= 2)Xmit Atmpts: Link Direct 3)Transmit Links 4)O 4 ptions 1)Xmit Type: TX Attempts=2 1 to 4 2 2)Xmit Atmpts: 4)Optio

Résumé du contenu de la page N° 14

Pocket Programmer Model UPP 1 1)Add Device View Device 2)Edit Device View is Read Only

1)Add Device View Device is used to check the 2 2)Edit Device current settings of a UPB device. Settings can be observed but not changed. 2)Edit Device 3 3)View Device To desired Select DevID=001 Select DevID=002 Device ID Select DevID=001 Err: ELSE Device Not

Résumé du contenu de la page N° 15

Pocket Programmer Model UPP Add Link is used to create and add 1 1)Access Network Add Link 2)New Network a Link to one or more UPB devices.

To desired Select Net ID=001 Select Net ID=002 Network ID Continue until Select Net ID=001 Select Net ID=001 Select Net ID=001 desired Select Pswd=0000 Select Pswd=1000 Select Pswd=1000 Password 1 1)Add Device 2)Edit Devi

Résumé du contenu de la page N° 16

Pocket Programmer Model UPP . 16

Résumé du contenu de la page N° 17

Pocket Programmer Model UPP UPB Explorer – Smart Transmit 1 1)Access Network 2)New Network 1)Smar 1 t Transmit Select Type=LINK Select Type=Link To select 2)Smart Receive Select NetID=001 Network ID 1)Access Network 2)Ne 2 w Network 1)Smart Transmit Select Type=DIRCT Link = 001 To select 2)Smar 2 t Receive 1)Activate Link ID

Résumé du contenu de la page N° 18

Pocket Programmer Model UPP . Smart Receive is used to observe UPB transmissions. 18

Résumé du contenu de la page N° 19

Pocket Programmer Model UPP . 19

Résumé du contenu de la page N° 20

Pocket Programmer Model UPP Simply Automated, Incorporated 5825 Avenida Encinas, Suite 101, Carlsbad, CA 92008 USA Technical Support: www.simply-automated.com or 800-630-9234 452-0031-0001 Rev. A Revised: May 16, 2006 20