Résumé du contenu de la page N° 1
IEEE802.11b
11Mbps
CompactFlash Card
Quick Installation Guide
M73-APO01-560
Résumé du contenu de la page N° 2
REGULATORY STATEMENTS FCC Certification The United States Federal Communication Commission (FCC) and the Canadian Department of Communications have established certain rules governing the use of electronic equipment. Part15, Class B This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interface, and 2) This device must accept any interface received, including interface that may cause undesired operat
Résumé du contenu de la page N° 3
SOFTWARE INSTALLATION FOR WINDOWS CE3.0 Connect your PDA to your PC. Make sure you have the Microsoft ActiveSync Utility installed on your PC to make an active connection. Caution: DO NOT insert the Wireless CompactFlash Card into the PDA BEFORE installing the configuration utility. 1. Insert the device driver CD into the CD-ROM drive. 2. Open the WINCE3.0 folder. 3. Inside the WINCE3.0 folder, click on PrismForPocketCE. For Handheld PC users: Please select PrismForHandHeldCE.
Résumé du contenu de la page N° 4
4. Click Next to continue. 5. Click OK. 6. Click Finish. - 3 -
Résumé du contenu de la page N° 5
7. You can now insert the Wireless CompactFlash Card into the PDA. Then use the Settings on your Windows CE to configure the network settings. - 4 -
Résumé du contenu de la page N° 6
HARDWARE INSTALLATION For PDA Insert the Wireless CF card into the Windows CE-based PDA by aligning the Wireless CF card toward the CF slot. For Notebook PC Note: This section is only for users who had CF to PCMCIA Adapter. Please refer to the manual for more details. 1. Plug the Wireless CF card into the PCMCIA Adapter. The Wireless CF card is then turning into a conventional PCMCIA type II PC Card. 2. Align the PC Card toward the PC Card slot with brand label facing upward, a
Résumé du contenu de la page N° 7
NETWORK CONNECTION FOR WINDOWS CE3.0 Once the driver has been installed, you must make some changes to your network settings. 1. Go to Start Settings Connections. Click on Network Adapters. 2. Highlight PRISM 11Mbps Wireless LAN Adapter, click Properties. - 6 -
Résumé du contenu de la page N° 8
3. Use server-assigned IP address If your network supports DHCP, select Use server-assigned IP address. The IP address and other information will be automatically assigned. Then click ok. Use server-assigned IP address If your network does not support DHCP, select Use specific IP address. You may need to enter the IP address and other information. When you have finished entering settings, click OK. If you forget to click OK, your settings will not take effect! - 7 -
Résumé du contenu de la page N° 9
4. A message as below may appear saying you must remove and re-insert the Wireless CompactFlash Card to have the changes take affect. Click OK. - 8 -
Résumé du contenu de la page N° 10
CONFIGURATION UTILITY FOR WINDOWS CE3.0 After installing the Wireless CompactFlash Card’s driver successfully, go to Start Programs. Click on PRISM Settings, the Network Status icon will appear in the task bar. Network Status Icon & Icon Menu The Status Icon Icon Link Status Green indicates a strong link. Yellow indicates a weak link. Red indicates no or a very poor link. - 9 -
Résumé du contenu de la page N° 11
Icon Menu After clicking on the icon, the icon menu as displayed below will prompt you to configure the Wireless CompactFlash Card. Items Description Wireless Radio On These two items allows you to enable or disable the Wireless Radio Off wireless radio. Remove Status Icon… Removes the Utility icon from the PDA’s system tray. Each time you power on your PDA, the icon will reappear. Clicking these items will Wireless Network launch the Wireless Status Settings window, as
Résumé du contenu de la page N° 12
All settings are categorized into 5 tabs: Link Configuration Encryption Site Survey About Link The Link tab provides you the status of the Wireless CompactFlash Card. Item Description State It displays the connection state of the Wireless CompactFlash Card with the wireless network. - 11 -
Résumé du contenu de la page N° 13
Item Description It displays the selected channel Current that is currently used. (There are Channel 14 channels available, depends on the country.) Click this button to enable/disable Enable Radio the wireless radio. The Wireless / Disable Radio CompactFlash Card will connect/disconnect with the wireless network. Search for all available networks. Rescan Clicking on the button, the device will start to rescan. Current Tx It displays the current transfer Rate rate. It displ
Résumé du contenu de la page N° 14
Item Description Saves values for all previous setting Profile parameters. The default values contain the parameters configured at Name installation. Once the demands for switching between different networking environments are required, you can also set the additional profiles to eliminate the configuration time. To save the current parameters, highlight the Profile field, type a new name, and click on the Apply button. A specific name shared among Network connected Wirele
Résumé du contenu de la page N° 15
Item Description It displays the type of BSS. Network Access Point: allows the Adapter to Type communicate with a wired network which employing an Access Point. Peer-to-Peer: allows PC-to-PC, station-to-station communication without employing an Access Point. To communicate with other Wireless Peer-to-Peer CompactFlash Card, you must specify Channel the same channel. Click the up and down arrow at the right of the Peer-to-Peer Channel to set the desired channel. It displays
Résumé du contenu de la page N° 16
Item Description Encryption WEP is a data privacy mechanism (WEP) based on a 64-bit/128-bit shared key algorithm. Under the drop-down box, you can choose to have WEP encryption Disabled, 64 bit, or 128 bit. Create Keys A Passphrase can be entered to with Passphrase generate four keys used for WEP. For the easiest configuration, the Passphrase method is recommended. Create Keys These four fields can be used to Manually enter WEP keys manually. The method is required to match t
Résumé du contenu de la page N° 17
Key 1: This setting is the configuration Key 2: key used in accessing the wireless Key 3: network via WEP encryption. Key 4: Use WEP Key The default key field can be used for specifying which of the four encryption keys to transmit data on the wireless network. Apply Click Apply to activate the settings. You must use the same value/phrase and WEP key settings for all wireless computers in order for the wireless network to function well. - 16 -
Résumé du contenu de la page N° 18
Site Survey The Site Survey tab shows all the available Access Points or Peer-to-Peer types and their features. Item Description Network The name must be identical for all Name devices and points attempting to connect to the same network. BSSID A set of wireless stations is referred to as a Basic Service Set (BSS). Computers in a BSS must be configured with the same BSS ID. Channel It shows the selected channel that is currently used. Network It displays the type of BSS. Type
Résumé du contenu de la page N° 19
Item Description WEP It displays the status of WEP Encryption Encryption. Signal Level It displays the signal strength of the connection between the Wireless CompactFlash Card and the Access Point it connects. Rescan Search for all available networks. Clicking on the button, the device will start to rescan and list all available sites. Connect To connect with a new access point, highlights the desired one in the left list box and clicks on the Connect button. Wait a while and t
