Instruction d'utilisation American Audio XDM-3633

Résumé du contenu de la page N° 1

XDM-3633
“COMMANDER”
professional preamp mixer
USER INSTRUCTIONS
djs wanted.

Résumé du contenu de la page N° 2

XDM-3633 “COMMANDER” The Ultimate DJ & Club Mixer! Main Features • 3 phono, 6 line, 3 auxiliaries & 3 mic inputs • Balanced outputs • Rotary Kills • High quality Feather Fader™ for smooth, clean crossfades (replaceable/Made in Japan) • Bass, mid, and treble for each channel • 2 independent microphones with separate bass, mid, & treble with Neutrik™ connection - 1/4” (6.3mm)/XLR • 2 zones with bass and treble • Zone 2 is assignable to any of the 4 channels • Mono/Stereo switches on Master & Zon

Résumé du contenu de la page N° 3

Index • Safety Instructions..................................................................................p.3 • Operating Determinations.......................................................................p.4 • Connections.............................................................................................p.4 • Functions (Front Panel)........................................................................p.5-6 • Inputs & Outputs (Rear Panel)..........................................

Résumé du contenu de la page N° 4

Operating Determinations When installing this mixer, please make sure that the device is not exposed to extreme heat, moisture or dust! There should not be any cables lying around. Doing so endangers you as well as others. Do not operate the mixer in extremely hot (more than 30° / 100°F) or extremely cold (less than 5°C / 40°F) surroundings. Keep away from direct sunlight and heaters. Operate the mixer only after becoming familiar with its functions. Do not permit operation by persons not qualif

Résumé du contenu de la page N° 5

Functions (Front Panel) 8 7 6 4 10 9 3 2 34 32 31 28 33 29 30 1 27 11 25 24 13 23 12 14 15 16 17 18 15 19 5 20 21 22 26 (1) POWER SWITCH - Red LED will light when power is ON. (2) LOW / MID / HI CONTROL - Used to increase or decrease the LOWs (bass), MIDs and HIs (treble) of the input signal for each channel. The XDM-3633 features “Rotary Kills” with -30dB to +20dB output control. (3) PHONO / AUX / LINE SWITCH - Used to select the input to be sent to the individual channel. Channels 1 and 2 may

Résumé du contenu de la page N° 6

Functions (Front Panel) Cont. (12) TALKOVER LEVEL - Adjust the TALKOVER volume on MIC 1. (13) MIC 1 / MIC 2 LEVEL FADER - Adjusts the microphone volumes of MIC 1 and MIC 2. MIC 3 levels may be adjust- ed with the CHANNEL 4 FADER (17) when the CH-4 LINE 5/LINE 6/MIC 3 SWITCH is set to MIC 3. (14) ASSIGN SWITCH - Used to switch the crossfader on or off. (15) CHANNEL ASSIGN SWITCH - Used to select which channel is to be mixed with another. (16) FEATHER FADER™ CROSSFADER - Mixes the signals of one c

Résumé du contenu de la page N° 7

Inputs and Outputs (Rear Panel) 35b 35a 42 41 GND GND AC INPUT 115/230V AUX 3 PHONO 3 AUX 2 PHONO 2 AUX 1 PHONO 1 LIGHT CONTROL RIGHT LEFT RECEIVE SEND 115V ZONE 2 ZONE 1 REC MASTER LINE 6 LINE 5 LINE 4 LINE 3 PHONO 3 LINE 2 PHONO 2 LINE 1 PHONO 1 AC VOLTAGE AUX 3 AUX 2 AUX 1 MIC 3 SELECTOR L R BALANCED OUTPUT EFFECT CH-4 CH-3 CH-2 CH-1 OUTPUT FUSE 37 38 45 44 43 40 39 38 49 48 47 46 50 (35a) (35b) GND (GROUND TERMINALS) - Connect the ground lead of the turntables with this terminal. Thi

Résumé du contenu de la page N° 8

Replacing the Crossfader  Disconnect from main power supply  Remove the fader knob.  Remove the two outer screws.  Take the fader out and unplug the connection cables.  Connect the new fader and replace back into mixer. Technical Specifications - model XDM-3633 Inputs: Line: 75mV, 27k Ohm  Microphone: 1.5mV, 600 Ohm  Phono: 1.2mV, 47k Ohm Output: Line: 9V, peak to peak  Headphones: 5W @ 47 Ohm  Distortion: less than 0.03% Signal-To-Noise Ratios: Line: Better than 88dB  Microphone: Bet