Résumé du contenu de la page N° 1
X-Monitor
Mixing Console
SERIES
Owner’s Manual
Résumé du contenu de la page N° 2
Specifications X-Monitor owner’s manual frequency response +0/-1dB 20Hz–20kHz ref 1kHz—any input to any output THD THD 20Hz–20kHz @ +15dBu out any output <.01% noise mic ein better-than -128dBu 20Hz–20kHz—150ohm source, 60dB gain crosstalk channel mute >80dB channel routing >80dB channel fader attenuation >90dB aux send attenuation >75dB 20Hz–20kHz—mic-in to main-out phase shift < +/- 30 degrees, XLR 4k ohm balanced—max voltage gain to group balanced out=98dB inputs mic-in TRS >10k ohm
Résumé du contenu de la page N° 3
Table of contents mono input module p. 6 1 Mic and line inputs group module p. 20 2 master section p. 28 3 microprocessor control p. 48 4 power supply p. 66 5 p. 3
Résumé du contenu de la page N° 4
p. 4 GROUP OUT X-MONITOR INPUT POST MAIN X-MONITOR GROUP FADER ( TO METERBRIDGE ) RIBBON GROUP PRE FDR PEAK (24 32 OR 40 FITTED) CONTROL (1 OF 12 SHOWN) Ø POST FDR CABLE +48V PRE-FADER GROUP SOLO CONTROL SOLO LEFT - GROUP FADER AMP & SWITCHING 50 WAY GRP PRE GRP POST BAL OUT TB TO FADER FADER SOLO RIGHT GROUP HPF TB +10 POST-FADER FEED 20 - 400HZ 26dB SIGNAL SOLO PAD PRESENT GROUP XFORMER BALANCED MUTE GAIN HPF LEVEL FREQ LEVEL FREQ LEVEL LEVEL TO OPTION IN 15 - 70 DB 20 - 400HZ NEXT MIX LINE Ø
Résumé du contenu de la page N° 5
How to use this manual Format This manual uses a format that is intended to be easy to read, yet technical for those who need to know all the details. For feature descriptions, this is done by devoting the left side of each page to 1) an overall module picture, 2) a block diagram, and 3) a control closeup.These images all pertain to the features and control descriptions on the right side of the page. Also, for certain features like the micro- processor system and the solo system that appear over
Résumé du contenu de la page N° 6
1 Mono input module X-Monitor owner’s manual Input Block diagram Module +48V 26dB PAD BALANCED GAIN HPF IN 15 - 70 DB 20 - 400HZ LINE Ø LINE P SW XFORMER OPTION LINE SPLIT HPF SW OUT INPUT PREAMP PIN 1 LIFT Controls p. 6
Résumé du contenu de la page N° 7
1 Mono input module Features Phantom power +48V The 48V switch should not be engaged when 48 volts DC is applied to pins 2 and 3 on the mic-input XLR connector. This option using standard (dynamic) is used with condenser microphones and active direct boxes that require an external DC microphones, or other voltage (phantom power) in order to operate. sources that do not use phantom power. Pad The mic-input signal is attenuated by 28dB to prevent some signals (e.g. kick drum or lead vocal) from
Résumé du contenu de la page N° 8
1 Mono input module X-Monitor owner’s manual Input Block diagram Module +48V 26dB PAD BALANCED GAIN HPF IN 15 - 70 DB 20 - 400HZ LINE Ø LINE P SW XFORMER OPTION LINE SPLIT HPF SW OUT INPUT PREAMP PIN 1 LIFT Controls p. 8
Résumé du contenu de la page N° 9
1 Mono input module Features If the channel peak Gain LED is illuminated, first try lowering The Input gain control range is closely related to the status of the PAD switch and the LINE the input gain control. switch. In order to establish proper gain structure in the console, input gain settings must Only when this method is be set correctly. unsuccessful should the pad switch be engaged. LINE—switch-up PAD—switch-up 12 to 72dB of gain can be added the mic-input signal. The impedance at t
Résumé du contenu de la page N° 10
1 Mono input module X-Monitor owner’s manual Input Block diagram Module X-MONITOR INPUT (24 32 OR 40 FITTED) GAIN HPF LEVEL FREQ LEVEL FREQ LEVEL LEVEL - 70 DB 20 - 400HZ EQ ON FADER AMP HF HI MID LOW MID LF 12 KHZ 400 - 8 KHZ 80 - 2 KHZ 100 HZ HPF +10 FOUR BAND EQ NPUT REAMP INPUT METER PRE SOUR SIG -6 0 +8 PEAK NO YES MUTE EQ FDR PRE SOURCE PRE SELECT PRE-SOURCE FADER AMP Controls p. 10
Résumé du contenu de la page N° 11
1 Mono input module Input EQ features Many audio signals coming into the console require some degree of corrective eq in order to be part of a good sounding mix.The X-Monitor Input EQ allows the user to tailor the incoming sound. The input EQ consists of four bands:high,high-mid,low-mid,and low. The high band is shelv- ing, the low band offers shelving cut with a bell boost. The two mid-bands are bell shaped with a Q of 2 and a generous overlap of adjacent operating frequencies. An independent,
Résumé du contenu de la page N° 12
1 Mono input module X-Monitor owner’s manual Input Controls Block diagram Module SOLO LEVEL TO NEXT MODULE EQ ON FADER AMP MUTE LF MUTE 100 HZ AND SOLO +10 CTRL SAFE 1 OF 4 PREVIEW CIRCUITS FROM PRE INPUT CHAN GROUP SENDS PREV SOURCE K MICRO MODULE NO YES 1-4 MUTE ? 1 THRU 12 INTERFACE PRE CARD EQ FDR 1 - LEV MIX 1 PRE 2 - PAN SOURCE MIX 2 SELECT PRE-SOURCE AMP 1-2 LEV/PAN CTRL 3 - LEV EQ FDR MIX 3 4 - PAN MIX 4 PRE DIR OUT POST 3-4 LEV/PAN CTRL 5-8 SELECT PRE 5 - LEV MIX 5 6 - PAN MIX 6 5-6
Résumé du contenu de la page N° 13
1 Mono input module Mix send features The X-Monitor input strip has twelve Mix sends. Pre/Post fader switching is done in three groups of four, 1 through 4, 5 through 8, and 9 through 12.These Mix sends are routed to their corresponding outputs for creating up to twelve individual mono monitor mixes.They can also be configured as stereo pairs,creating up to six stereo mixes.When configured for stereo operation, the odd numbered pot becomes the stereo level control and the even numbered pot beco
Résumé du contenu de la page N° 14
1 Mono input module X-Monitor owner’s manual Input Controls Block diagram Module SOLO LEVEL TO NEXT MODULE EQ ON FADER AMP MUTE LF MUTE 100 HZ AND SOLO +10 CTRL SAFE 1 OF 4 PREVIEW CIRCUITS FROM PRE INPUT CHAN GROUP SENDS PREV SOURCE K MICRO MODULE NO YES 1-4 MUTE ? 1 THRU 12 INTERFACE PRE CARD EQ FDR 1 - LEV MIX 1 PRE 2 - PAN SOURCE MIX 2 SELECT PRE-SOURCE AMP 1-2 LEV/PAN CTRL 3 - LEV EQ FDR MIX 3 4 - PAN MIX 4 PRE DIR OUT POST 3-4 LEV/PAN CTRL 5-8 SELECT PRE 5 - LEV MIX 5 6 - PAN MIX 6 5-6
Résumé du contenu de la page N° 15
1 Mono input module Level meter features Level meter LED LED LED LED LED Each input includes a five-segment LED meter for visually moni- toring signal levels.This is essential for setting up and maintaining proper gain structure. Peak indicator—PK LED The input signal is monitored at several points throughout the channel.These points are the mic preamp, the EQ stage and the fader stage. Overload at any of these stages will cause the red peak-LED to light. The channel gain should reduced if this
Résumé du contenu de la page N° 16
1 Mono input module X-Monitor owner’s manual Input Controls Block diagram Module SOLO LEVEL TO NEXT MODULE EQ ON FADER AMP MUTE LF MUTE 100 HZ AND SOLO +10 CTRL SAFE 1 OF 4 PREVIEW CIRCUITS FROM PRE INPUT CHAN GROUP SENDS PREV SOURCE K MICRO MODULE NO YES 1-4 MUTE ? 1 THRU 12 INTERFACE PRE CARD EQ FDR 1 - LEV MIX 1 PRE 2 - PAN SOURCE MIX 2 SELECT PRE-SOURCE AMP 1-2 LEV/PAN CTRL 3 - LEV EQ FDR MIX 3 4 - PAN MIX 4 PRE DIR OUT POST 3-4 LEV/PAN CTRL 5-8 SELECT PRE 5 - LEV MIX 5 6 - PAN MIX 6 5-6
Résumé du contenu de la page N° 17
1 Mono input module Bus assignment features In addition to providing full variable send capabilities in the Mix section,the X-Monitor also offers audio grouping facilities for sending input signals to the output matrix section, and directly to the A and B output masters for creating additional mixes. All assignments are normally derived Post-fader(post-eq and post-mute). Bus assignments 13, 14, 15 & 16 The input signal is assigned to Buses 13 thru 16 which feed Matrix 1 - 4, located above the m
Résumé du contenu de la page N° 18
1 Mono input module X-Monitor owner’s manual X-Monitor rear-view (28 channel, 40 position frame shown) Input Module Lamp Dim To Meter Bridge Matrix 4 Matrix 3 Matrix 2 Matrix 1 Dir Out Dir Out Dir Out Dir Out Dir Out Dir Out Dir Out Dir Out Dir Out Dir Out Dir Out Dir Out Dir Out Dir Out Dir Out Dir Out Dir Out Dir Out Dir Out Dir Out Dir Out Dir Out Dir Out Dir Out Ext Ext Ext Ext In In In In 12 11 10 9 8 7 6 5 4 3 2 1 Group Out Group Out Group Out Group Out Group Out Group Out Group
Résumé du contenu de la page N° 19
1 Mono input module Rear panel features Direct out 1/4" TRS jack T= OUT + R= G COMP S= GND The input channel's signal is available at this output jack.The D.O.signal is derived Post-fader (post-eq and post-mute).This output jack is ground-compensated. Insert points Separate 1/4" TRS jacks provide the facilities for inserting an external signal processor into the signal path of the input channel. Insert send T= OUT + R= G COMP S= GND This jack serves as an output for connection to the input of
Résumé du contenu de la page N° 20
2 Output groups X-Monitor owner’s manual Group Controls Module Pair Block diagram X-MONITOR GROUP GROUP OUT ( TO METERBRIDGE ) GROUP PRE FDR PEAK (1 OF 12 SHOWN) Ø POST FDR GROUP GROUP FADER AMP BAL OUT TB TO GRP PRE GRP POST FADER FADER GROUP HPF TB +10 FEED 20 - 400HZ SIGNAL PRESENT XFORMER GROUP MUTE OPTION MIX 1 TO 12 HPF ∑ GC GROUP MIX AMP FF LEV Q LEV F Q LEV F Q LEV F LEV GROUP EQ INSERT SEND ON GROUP PRE FDR POST FDR SOLO CONTROL & SWITCHING LOC RTN PRE POST HF HI MID MID LO MID LF 2-16
