Résumé du contenu de la page N° 1
NWZ-X1050/X1051/
X1060/X1061
US Model
SERVICE MANUAL
NWZ-X1051/X1061
Ver. 1.0 2009.05
Canadian Model
Taiwan Model
NWZ-X1060
AEP Model
UK Model
E Model
Note:
Australian Model
Be sure to keep your PC used for service and
checking of this unit always updated with the
Chinese Model
latest version of your anti-virus software.
In case a virus affected unit was found during
Tourist Model
service, contact your Service Headquarters.
NWZ-X1050/X1060
Photo: NWZ-X1050
SPECIFICATIONS
Supported file form
Résumé du contenu de la page N° 2
NWZ-X1050/X1051/X1060/X1061 Maximum recordable number of photos that can be transferred (Approx.) OpenMG, ATRAC, ATRAC3, ATRAC3plus, ATRAC Advanced Lossless and their logos are trademarks of Sony Corporation. Max. 20,000 “WALKMAN” and “WALKMAN” logo are registered trademarks of Sony Corporation. Recordable number of photos may be less depending on file sizes. Microsoft, Windows, Windows Vista and Windows Media are trademarks or registered trademarks of Microsoft Corporation in the United Stat
Résumé du contenu de la page N° 3
NWZ-X1050/X1051/X1060/X1061 SECTION 1 SERVICING NOTES TABLE OF CONTENTS CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. 1. SERVICING NOTES ............................................. 3 2. DISASSEMBLY UNLEADED SOLDER 2-1. Disassembly Flow ........................................................... 8 Boards requiring use of unleaded solder are printed with the lead- 2-2. Panel (Rear) .........................................
Résumé du contenu de la page N° 4
NWZ-X1050/X1051/X1060/X1061 NOTE THE MAIN BOARD REPLACING When the MAIN board is replaced, process it according to the fol- lowing. 1. Format Format You can format the built-in flash memory of the player. Notes If the memory is formatted, all data (songs, videos, photos, etc., including sample data installed at the factory) will be erased. Be sure to verify the data stored in memory prior to formatting and export any important data to the hard disk of your computer. Be sure not to init
Résumé du contenu de la page N° 5
NWZ-X1050/X1051/X1060/X1061 • Please cut out along the dotted line and use it. Note: Note: The MAC address of this set was changed along with this repair. The MAC address of this set was changed along with this repair. Please set it again if you are using the MAC address fi ltering function Please set it again if you are using the MAC address fi ltering function of access point device of connection destination. of access point device of connection destination. Please refer to the operation guide
Résumé du contenu de la page N° 6
NWZ-X1050/X1051/X1060/X1061 MEMO 6
Résumé du contenu de la page N° 7
NWZ-X1050/X1051/X1060/X1061 Connection location: Note: Refer to page 27 for the schematic diagram. Refer to page 28 for the printed wiring boards. – MAIN Board (Side B) – METHOD OF JUDGING RIGHT AND WRONG OF S881 PARTS RELATED TO SWITCH (HOLD SW) 2 S881 In this set, only a part of parts that relate to the switch are supplied. 1 Exchange the entire mounted board when parts that do not corre- spond to it are defective. The right and wrong of the switch can be judged by the following
Résumé du contenu de la page N° 8
NWZ-X1050/X1051/X1060/X1061 SECTION 2 DISASSEMBLY • This set can be disassembled in the order shown below. 2-1. DISASSEMBLY FLOW SET 2-2. PANEL (REAR) (Page 9) 2-3. HOLD ASSY (Page 9) 2-4. MAIN BOARD ASSY (INCLUDING BATTERY ASSY) (Page 10) 2-6. 5PIN HP JACK ASSY (J001), 2-5. BATTERY ASSY CHASSIS SECTION (BATT1), (Page 11) MAIN BOARD (Page 10) 2-8. EL INDICATOR 2-10. BUTTON (VOL), 2-7. KEY FLEXIBLE PRINT 2-9. HOME KEY BOARD, ELEMENT (EL01) KNOB (NC) BOARD (FPC1), GUARD (MULTI) (
Résumé du contenu de la page N° 9
NWZ-X1050/X1051/X1060/X1061 Note: Follow the disassembly procedure in the numerical order given. 2-2. PANEL (REAR) Note 1: This illustration sees the set from rear side. panel (rear) 8 Note 2: Please work noting that the panel (rear) is damaged. two adhesive sheet 7 (rear) panel rear section 3 claw hold assy 4 5 claw 2 Peel off panel (rear) section of (panel) the hold assy side in the adhesive 6 plate (rear) sheet (rear) two places. 1 two screws (M1.4) 2-3. HOLD ASSY Note: This il
Résumé du contenu de la page N° 10
NWZ-X1050/X1051/X1060/X1061 2-4. MAIN BOARD ASSY (INCLUDING BATTERY ASSY) Note: This illustration sees the set from rear side. MAIN board assy (including battery assy) q; 5pin HP jack assy flexible board 5 Move the MAIN board assy 7 (CN301) 9 EL indicator element in the direction of the arrow. flexible board (CN801) 6 two screws (M1.4) 1 cushion (B connector) 3 key flexible print board (CN881) battery connector 2 (CN901) 8 Open the MAIN board assy in the 4 touch panel modul
Résumé du contenu de la page N° 11
NWZ-X1050/X1051/X1060/X1061 2-6. 5PIN HP JACK ASSY (J001), CHASSIS SECTION Note 1: This illustration sees the set from rear side. 1 two screws (M1.4) holder (jack) 2 3 5pin HP jack assy (J001) insulation sheet 4 (O-FPC) 5 two screws (M1.4) 7 chassis section 6 Open the EL indicator element in the direction of the arrow. Note 2: Please work noting that the EL indicator element flexible board is damaged. 11
Résumé du contenu de la page N° 12
NWZ-X1050/X1051/X1060/X1061 2-7. KEY FLEXIBLE PRINT BOARD (FPC1), CHASSIS 1 two claws 3 lid (top) Note 1: Please work noting that the key flexible print board (FPC1) is damaged. 6 Peel off key flexible print board (FPC1) of the base (top) top side. 4 two adhesive sheets (button) 2 5 button (top) 8 base (top) qd key flexible print board (FPC1) 7 adhesive sheet (top) 9 spacer (vol) qs Peel off key flexible print board (FPC1) of the chassis. Note 2: Please work noting that the key fle
Résumé du contenu de la page N° 13
NWZ-X1050/X1051/X1060/X1061 2-9. HOME KEY BOARD, GUARD (MULTI) Note: This illustration sees the set from rear side. – front side – three claws 2 adhesive sheet 6 3 button (home) assy (home PWB) 4 HOME KEY board is lightiy pushed from button side. 5 HOME KEY board 1 dot connector (CN001) guard (multi) 8 Note 2: They are important parts. Do not forget to install it. 7 two claws 2-10. BUTTON (VOL), KNOB (NC) Note: This illustration sees the set from rear side. 1 button (vol) 2 bracke
Résumé du contenu de la page N° 14
NWZ-X1050/X1051/X1060/X1061 2-11. TOUCH PANEL MODULE (TPM1), FRAME 8 adhesive sheet (lid) 9 adhesive sheet (lid.B) 4 Please work noting that the touch panel module section is damaged of the frame. q; frame 3 adhesive sheet (catch) adhesive sheet (window) 7 Note 2: Adhesive sheet (window) cannot re-used. please replace to brand-new part ones adhesive sheet (window) is removed. 5 cushion (OLED) 1 spacer (window) 6 touch panel module (TPM1) 2 Peel off touch panel module flexible board
Résumé du contenu de la page N° 15
NWZ-X1050/X1051/X1060/X1061 SECTION 3 TEST MODE 4-1-1. Power supply voltage check (VCHK) Note 1: Information on the test mode must correspond in enough This mode is used in case power supply voltage in the state where security. When the leakage has been revealed by any chance, the source of information is specifi ed. all power supply lines are starting is checked. Note 2: Execute “EXITTEST” when you release the test mode. Checking method: 1. Enter the test mode. 1. SETTING THE TEST MODE 2
Résumé du contenu de la page N° 16
NWZ-X1050/X1051/X1060/X1061 4-1-3. Standby current check (DSVCHK) 4-1-5. Battery voltage detection check (BATTCHK) This mode is used in case standby current is checked. This mode is used in case battery voltage is checked. Checking method: Checking method: 1. Enter the test mode. 1. Enter the test mode. 2. Press the [ ]/[ ] key to select the “POWER”, and press 2. Press the [ ]/[ ] key to select the “POWER”, and press > . > . the [u] key to enter the minor item. the [u] key to enter the minor it
Résumé du contenu de la page N° 17
NWZ-X1050/X1051/X1060/X1061 4-2-1. Output check (OUTPUT) 4-2-3. Frequency characteristic 1 check (F1) “1 kHz 0 dBs L-ch/R-ch VOLUME: 25” audio signal is outputted. “20 Hz 0 dBs L-ch/R-ch VOLUME: 25” audio signal is outputted. Checking method: Checking method: 1. Enter the test mode. 1. Enter the test mode. 2. Press the [ ]/[ ] key to select the “AUDIO”, and press 2. Press the [ ]/[ ] key to select the “AUDIO”, and press > . > . the [u] key to enter the minor item. the [u] key to enter the minor
Résumé du contenu de la page N° 18
NWZ-X1050/X1051/X1060/X1061 4-2-5. CH separation (L-ch) check (SEPLR) 4-2-7. Maximum output check (MAXOUT) “1 kHz 0 dBs L-ch VOLUME: 25” audio signal is outputted. “1 kHz 0 dBs L-ch/R-ch VOLUME: 30” (Headphone output when AVLS operates: “1 kHz 0 dBs L-ch/R-ch VOLUME: 14”) audio Checking method: signal is outputted. 1. Enter the test mode. 2. Press the [ ]/[ ] key to select the “AUDIO”, and press Checking method: > . the [u] key to enter the minor item. 1. Enter the test mode. 3. Press the [>]/
Résumé du contenu de la page N° 19
NWZ-X1050/X1051/X1060/X1061 4-2-9. Sound pressure regulation level check (SPCHK) 4-2-11. User specifi cation contents playback 1 (USER1) “1 kHz 0 dBs L-ch/R-ch VOLUME: 30” audio signal is outputted. “/User1.oma” is reproduced. Checking method: Checking method: 1. Enter the test mode. 1. Enter the test mode. 2. Press the [ ]/[ ] key to select the “AUDIO”, and press 2. Press the [ ]/[ ] key to select the “AUDIO”, and press > . > . the [u] key to enter the minor item. the [u] key to enter the minor
Résumé du contenu de la page N° 20
NWZ-X1050/X1051/X1060/X1061 4-2-13. User specifi cation contents playback 3 (USER3) 4-3-1. LCD display check (LCD) “/User3.oma” is reproduced. Screen display is checked. Checking method: Checking method: 1. Enter the test mode. 1. Enter the test mode. 2. Press the [ ]/[ ] key to select the “AUDIO”, and press 2. Press the [ ]/[ ] key to select the “VIDEO”, and press > . > . the [u] key to enter the minor item. the [u] key to select the “LCD”. 3. Press the [>]/[.] key to select the “USER3”. 3. Pre
