Résumé du contenu de la page N° 1
For Quick For Quick
Star Startt Installation Installation
SmartNode 4400
IpChannel Bank
Quick Start Guide
Important
This is a Class A device and is intended for use in a light industrial environment. It is not intended nor approved for use in an industrial
or residential environment.
Sales Office: +1 (301) 975-1000
Technical Support: +1 (301) 975-1007
E-mail: support@patton.com
WWW: www.patton.com
Part Number: 07MSN4400-QS, Rev. B
Revised: January 13, 2010
Résumé du contenu de la page N° 2
Patton Electronics Company, Inc. 7622 Rickenbacker Drive Gaithersburg, MD 20879 USA Tel: +1 (301) 975-1000 Fax: +1 (301) 869-9293 Support: +1 (301) 975-1007 Web: www.patton.com E-mail: support@patton.com Trademark Statement The terms SmartNode, SmartWare, and SmartView are trademarks of Patton Electronics Company. All other trademarks presented in this document are the prop- erty of their respective owners. Copyright © 2010, Patton Electronics Company. All rights reserved.
Résumé du contenu de la page N° 3
SmartNode 4400 Quick Start Guide Safety when working with electricity The SmartNode contains no user serviceable parts. The equipment shall be returned to Patton Electronics for repairs, or repaired by qualified service per- sonnel. Opening the SmartNode case will void the warranty. Mains Voltage: Do not open the case the when the power cord is attached. Line voltages are present within the power supply when the power cords are connected. The mains outlet that is utilized to power the
Résumé du contenu de la page N° 4
SmartNode 4400 Quick Start Guide Introduction This Quick Start Guide leads you through the basic steps to set up a new SmartNode and to download a con- figuration. Please note that this guide does not replace the detailed Software Configuration Guide and the Get- ting Started Guide on the CD-ROM and available online at www.patton.com/voip. SmartNodes can be used for a wide variety of IP and voice over IP applications. To support and ease the config- uration of the SmartNo
Résumé du contenu de la page N° 5
SmartNode 4400 Quick Start Guide Connecting a PC, logging in, and configuring the LAN IP address Connecting power and configuring the default IP address Connect the SmartNode to the mains power supply using the included power supply and cable. When the RUN LED stops blinking and remains lit, the SmartNode is ready. The factory default IP settings are listed in table 1. If these addresses do not work with your network they must be changed. Contact your network administrator
Résumé du contenu de la page N° 6
SmartNode 4400 Quick Start Guide 3. Type administrator as the login prompt and press the Enter key after the password prompt (do not type anything for the password). A prompt will appear consisting of the IP address and > character. login:administrator password: 172.16.40.1> 4. Following log in, the SmartNode is in operator execution mode (indicated by > character in the command line prompt). With the commands en
Résumé du contenu de la page N° 7
SmartNode 4400 Quick Start Guide Connecting the SmartNode to the LAN The 4400 Ethernet ports are auto MDX, therefore a straight-through wired cable can be used for host and switch connections (see figure 3). WAN LAN (ETH 0/0) Network LAN (ETH 0/1) PC or workstation interface or Telnet Internet or WAN (optional) Figure 3. Connecting the SmartNode to the network You can check the connection with the ping command to another host on the local LAN. 172.16.1.99(if-ip)[eth0]#ping <
Résumé du contenu de la page N° 8
SmartNode 4400 Quick Start Guide Downloading a configuration example, adapting it to your network, and loading it onto the SmartNode Patton provides a collection of configuration templates on the CD-ROM that came with the SmartNode device—and also on the support page at www.patton.com/voip/appnotes.shtml—one of which may be simi- lar enough to your application that you can use it to speed up configuring the SmartNode. Simply download the configuration note that matches your application to yo
Résumé du contenu de la page N° 9
SmartNode 4400 Quick Start Guide Compliance EMC compliance: • FCC Part 15, Class A • EN55022, Class A • EN55024 • EN-61000-3-2 Harmonics • EN-61000-3-3 Flicker • EN-61000-4-2 ESD • EN-61000-4-3 Radiated Immunity • EN-61000-4-4 EFT • EN-61000-4-5 Surge • EN-61000-4-6 Low Frequency Common Immunity • EN-61000-4-11 Voltage Dips and Sags Safety compliance: • UL60950-1/CSA C22.2 No. 60950-1 • IEC/EN 60950-1 • AS/NZS 60950-1 CE Declaration of Conformity This equipment conforms to the requirements of C
Résumé du contenu de la page N° 10
SmartNode 4400 Quick Start Guide NOTES NOTES 10
Résumé du contenu de la page N° 11
SmartNode 4400 Quick Start Guide NOTES NOTES 11
Résumé du contenu de la page N° 12
SmartNode 4400 Quick Start Guide NOTES NOTES 12
