Résumé du contenu de la page N° 1
PARTS AND OPERATION MANUAL
PLASTER/ MORTAR MIXERS
EM-900S
EM-900P
Revision #7 (06/26/01)
MULTIQUIP INC. .. . . PARTS DEPARTMENT:
18910 WILMINGTON AVE. 800-427-1244
CARSON, CALIFORNIA 90746 FAX: 800-672-7877
310-537-3700 SERVICE DEPARTMENT:
800-421-1244 800-478-1244
FAX: 310-537-3927 FAX: 310-537-4259
E-mail:mq@multiquip.com � www:multiquip.com
Atlanta • Boise Dallas Houston Newark
Montreal, Canada Manchester, UK
Rio De Janiero, Brazil Guadalajara, Mexico
© COPYRIGHT 2001,
Résumé du contenu de la page N° 2
PAGE 2 — ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01)
Résumé du contenu de la page N° 3
HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING PARTS DEPARTMENT 800-427-1244 or 310-537-3700 FAX: 800-672-7877 or 310-637-3284 SERVICE DEPARTMENT/TECHNICAL ASSISTANCE 800-478-1244 or 310-537-3700 FAX: 310- 537-4259 WARRANTY DEPARTMENT 888-661-4279, or 310-661-4279 FAX: 310- 537-1173 MAIN 800-421-1244 or 310-537-3700 FAX: 310-537-3927 ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01) — PAGE 3
Résumé du contenu de la page N° 4
TABLE OF CONTENTS Here's How To Get Help .......................................... 3 Table Of Contents ................................................... 4 Parts Ordering Procedures ..................................... 5 Rules for Safe Operation & Safety Decals .............. 6 Warranty .................................................................. 7 ESSICK — 900S & 900P Operations ......................................................... 8-11 Specifications ..............................
Résumé du contenu de la page N° 5
PARTS ORDERING PROCEDURES n Dealer account number n Dealer name and address n Shipping address (if different than billing address) n Return fax number n Applicable model number n Quantity, part number and description of each part n Specify preferred method of shipment: UPS Ground UPS Second Day or Third Day* UPS Next Day* Federal Express Priority One (please provide us with your Federal Express account number)* Airborne Express* Truck or parcel post *Normally shipped the same day the
Résumé du contenu de la page N° 6
RULES FOR SAFE OPERATION & SAFETY DECALS Do not operate or service this equipment When towing, an adequate safety chain before reading the operating and must be fastened to the frame, refer to page 9. maintenance instructions manual or serious Keep all inexperienced and unauthorized injury may result. people away from the equipment at all times. Do not operate this equipment unless all Unauthorized equipment modifications will guards and safety devices are attached and void all warrant
Résumé du contenu de la page N° 7
WARRANTY There are no warranties, express or implied, made by Multiquip There are no warranties, express or implied, in addition to the Inc. hereunder on Products manufactured or distributed by it above except as may be provided in writing by Multiquip Inc. except the warranty against defects in material and workmanship MULTIQUIP INC. SHALL NOT BE LIABLE FOR ANY SPECIAL, on new Products to the original purchaser, as hereinafter set INDIRECT OR CONSEQUENTIAL DAMAGES. forth. THE FOREGOING WARRANTI
Résumé du contenu de la page N° 8
EM-900S & 900P — OPERATIONS CONTROLS KILL SWITCH: (Gasoline Engine Only) Located on the side of the engine cover. ENGINE THROTTLE AND CHOKE CONTROLS: Please refer to the engine owners manual for specific instructions. The electric motor switch ( electric motor only) located on the motor — is used to start and stop the mixer. DUMP LATCH: To dump the tub, grasp the dump handle and lift the dump latch, then rotate the tub to discharge the mix. After, discharge, return the tub to the vertical mixing
Résumé du contenu de la page N° 9
EM-900S & 900P — OPERATIONS PADDLE SHAFT BEARING IMPORTANT — DRUM HEAD SEAL CARE The paddle shaft in the Essick Mixer rotates in sealed ball On each end of the mixing drum is a drum head containing self bearings requiring no additional lubrication. adjusting paddle shaft seals. These seals consist of packing rings, split glands and spring actuated adjusters. A properly maintained seal prevents material from working around the BEARING BRACKET paddle shaft, causing excessive wear. The following is
Résumé du contenu de la page N° 10
EM-900S & 900P — OPERATIONS TOWING — Before towing, check with local and state STEP 1 laws for proper compliance. The tow bar and chain must be properly attached to the mixer and towing vehicle prior to towing. Refer to the following DRAW BAR installation instruction: Step 1. Insert the Draw Bar into the main frame. Secure, utilizing the ¾" bolt (grade 5) and nylock nut. Tighten to 100 foot pounds. Step 2. Install the chain through the hole located between the BOLT & NUT frame gusset and frame a
Résumé du contenu de la page N° 11
EM-900S & 900P — OPERATIONS CLEANING — BLADE ADJUSTMENTS Always disconnect the spark plug wire before cleaning the inside of the drum. Never pour or spray water over the gasoline engine or electric motor. For consistent performance, long life and high quality mixing, thoroughly clean the mixer inside and out at the end of each day’s operation. To prevent lumps of dried mortar from forming and contamination of future batches, do not allow a buildup of materials to form on the blades or anywhere i
Résumé du contenu de la page N° 12
EM-900S & 900P — SPECIFICATIONS EM-900S SPECIFICATIONS MODEL U.S.(inch) METRIC CAPACITY ....................................................9 CUBIC FEET ....................................................... 248 LITERS BAG CAPACITY .............................................2½ - 3½ ............................................................ 2½ - 3½ WEIGHT (APPROX.).......................................780 LBS. ............................................................. 395 KG. L X W X H .
Résumé du contenu de la page N° 13
NOTE PAGE ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01) — PAGE 13
Résumé du contenu de la page N° 14
EXPLANATION OF CODE IN REMARKS COLUMN How to read the marks and remarks used in this parts book. Section 1: Items Found In the “Remarks” Column Serial Numbers-Where indicated, this indicates a serial number range (inclusive) where a particular part is used. Model Number-Where indicated, this shows that the corresponding part is utilized only with this specific model number or model number variant. Section 2: Items Found In the “Remarks” Column Serial Numbers-Where indicated, this indicates a ser
Résumé du contenu de la page N° 15
EM-900S & 900P — SUGGESTED SPARE PARTS EM-900 S/P EM-900 S/P 1 to 3 Units 5+ Units Qty. P/N Description Qty. P/N Description 3 ......... EM505834 ........... V-BELT 5 ......... EM505834 ........... V-BELT 3 ......... 491115 ................ V-BELT, w/ELECTRIC MOTOR 5 ......... 491115 ................ V-BELT, w/ELECTRIC MOTOR 6 ......... 491010 ................ LATCH w/ASSY 10 ....... 491010 ................ LATCH w/ASSY 3 ......... EM200863 ........... BLADE KIT STEEL DRUM 5 ......... EM200863 .
Résumé du contenu de la page N° 16
EM-900S & 900P — DRUM HEAD ASSEMBLY PAGE 16 — ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01)
Résumé du contenu de la page N° 17
EM-900S & 900P — DRUM HEAD ASSEMBLY DRUM HEAD ASSEMBLY DRUM HEAD NO. PART NO. PART NAME QTY. REMARKS 4 EM200018 COLLAR 1 5 EM902153 BEARING 2 6 EM507720 DUMP BEARING ..................................................................... 2 ................. STARTING S/N 98624090 6 500076 DUMP BEARING ..................................................................... 2 ................. FROM S/N 9862400 TO 9862489 7 EM916019 GREASE ZERK ...........................................................
Résumé du contenu de la page N° 18
EM-900S, 900P — PADDLE SHAFT ASSEMBLY 46 47 48 49 61 58 59 60 TOW END PAGE 18 — ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01)
Résumé du contenu de la page N° 19
EM-900S, 900P — PADDLE SHAFT ASSEMBLY PADDLE SHAFT ASSEMBLY NO. PART NO. PART NAME QTY. REMARKS 46 EM200297 U-BOLT 2 47 EM968011 NUT HEX ½-13 4 48 EM200292 U-BOLT INSERT 4 49 EM507274 PADDLE SHAFT 50 EM200293 PADDLE ARM-TOW END 1 51 EM200294 PADDLE ARM-CENTER 1 52 EM200296 PADDLE ARM-ENGINE END 1 53 EM200295 PADDLE ARM-CENTER 1 54 # EM203432 CENTER BACK-UP BLADE 4 * 55 # EM203433 END BACK-UP BLADE 2 * 56 EM200212 TOP RUBBER BLADE (STEEL) DRUM ONLY 4 * 56# EM507519 TOP PLASTIC BLADE (POLY) DRUM O
Résumé du contenu de la page N° 20
EM-900S — STEEL DRUM STEEL DRUM 109 110 111 108 PAGE 20 — ESSICK EM-900S & 900P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01)
