Instruction d'utilisation Thermador MET27B, MET30B

Résumé du contenu de la page N° 1

INSTALLATION
INSTRUCTIONS
Oven
For Built - in Microwave Ovens
Model
MBB
Built-In
Trim Kits
Models:
MET27B
MET30B
(Sold Separately)

Résumé du contenu de la page N° 2

Please read this entire manual before proceeding IMPORTANT: Local codes vary. Installation, electrical connections, circuit breakers and grounding must comply with all applicable codes. Save these instructions for your local electrical inspector's use. INSTALLER: Please leave these Installation Instructions with this unit for the owner. OWNER: Please retain these instructions for future reference. WARNING: Disconnect power at the breaker before installing. Table of Contents Step 1: Unpacking ..

Résumé du contenu de la page N° 3

Step 1: Unpacking A. Tools Needed: Caution: • Tape Measure • Trim kits are designed for use • Drill with 1/16" bit only with the Thermador • Pliers microwave oven models listed • # 2 Phillips Head Screwdriver (See Table 1). • Gloves • Safety Goggles • For safety, do not alter or modify any part of this kit or Microwave Oven Model MBB oven. Remove and discard all packing • Unit is heavy and requires at material. least two people to lift or move. Parts Included: • Care & Use manual (1) • Warranty

Résumé du contenu de la page N° 4

➛ ➝ ➛ ➛ ➝ Step 2: Preparing the Cabinet • Your microwave oven can be installed into a • The cabinet cutout dimensions are shown in cabinet or wall by itself or above any of the Figure 1. following Thermador wall ovens: C271, C301, • It is a good practice when the microwave oven is CM301, S301, SC301. Or, Thermador Warming installed at the end of a cabinet run, adjacent to a Drawers WD27 and WD30 (see Figures 2a and perpendicular wall or cabinet door, to allow at least 2b). 1 /2" (12.7 mm) spac

Résumé du contenu de la page N° 5

Step 3: Preparing the Electric The Thermador microwave oven is equipped with a grounded cord. The wall receptacle must be installed and grounded in accordance with the national electrical code. It can be installed anywhere in the shaded area in Figure 1 (previous page). Electrical connections and grounding must comply with all applicable local codes. The electrical requirements for a separate circuit serving only this microwave oven are: 120V, 60Hz, 15Amp. WARNING: Improper grounding can resu

Résumé du contenu de la page N° 6

Step 5: Installing The Ducts 4. Attach base pan to bottom of microwave at 1. Remove and discard the protective plastic leg holes. Fasten with two (2) 7/16" lag bolts. film from the 4 ducts. Install one bolt through front right leg hole and one through back left hole. Return mi- crowave to right-side-up position. CAUTION 2. Loosen the outer case screw near the vent The ducts have sharp edges. Be careful when on left side of the microwave. handling. 3. Position side duct on left side of oven. Sl

Résumé du contenu de la page N° 7

Step 6: Completing the Installation Caution: The microwave oven is heavy. Al- ways use at least two people to lift the unit. 1. Lift oven into position and rest right rear cor- ner in cabinet cutout. 2. Reach past microwave on left side to insert electrical cord into outlet. 3. Slide oven the rest of the way into the cabi- net. Position microwave in cabinet so that base pan center hole aligns with cabinet centerline. When properly installed, the front end of pan will be flush with the front

Résumé du contenu de la page N° 8

Thermador reserves the right to change specifications or design without notice. Some models are certified for use in Canada. Thermador is not responsible for products which are transported from the United States for use in Canada. Check with your local Canadian distributor or dealer. Thermador, 5551 McFadden Avenue, Huntington Beach, CA 92649. For the most up-to-date critical installation dimensions by fax, use your fax handset and phone 702/833-3600. Use code #8030. BSH Home Appliances Corpora