Résumé du contenu de la page N° 1
Installation Over the Range
Instructions Microwave Oven
1-800-944-9044(US)
Questions? Call or Visit our Website at:
http://www .frigidaire.com
1-800-265-8352(Canada)
BEFORE YOU BEGIN
Read these instructions completely and carefully.
• Note to Consumer – Keep these
instructions for future reference.
•
IMPORTANT – Save these
• Skill level – Installation of this appliance requires
instructions for local inspector’s use.
basic mechanical and electrical skills.
•
IMPORTANT – Observe all • Proper in
Résumé du contenu de la page N° 2
Installation Instructions Adapting Microwave Blower CONTENTS – for Outside Back Exhaust................17 18 General information Mount the Microwave Oven ................19 Important Safety Instructions .................................. 3 Recirculating ........................................20 –22 C Electrical Requirements .......................................... 3 Attach Mounting Plate to Wall ............20 Damage – Shipment/Installation.............................. 4 Preparation of Top C
Résumé du contenu de la page N° 3
Installation Instructions IMPORTANT SAFETY INSTRUCTIONS This product requires a three-prong grounded outlet. You should have the wall receptacle and circuit checked The installer must perform a ground continuity check by a qualified electrician to make sure the receptacle is on the power outlet box before beginning the properly grounded. installation to insure that the outlet box is properly Where a standard two-prong wall receptacle is grounded. If not properly grounded, or if the outlet enco
Résumé du contenu de la page N° 4
INSTALLATION INSTRUCTIONS Installation Instructions PARTS INCLUDED (CONT.) DAMAGE—SHIPMENT/ INSTALLATION ADDITIONAL PARTS • If the unit is damaged in shipment, return the PART QUANTITY unit to the store in which it was bought for repair or replacement. Top Cabinet 1 TOP CABINET TEMPLATE Template • If the unit is damaged by the customer, repair or replacement is the responsibility of the customer. • If the unit is damaged by the installer (if other than the customer), repair or replacement mus
Résumé du contenu de la page N° 5
Installation Instructions TOOLS YOU WILL NEED Ruler or tape measure and straight edge Pencil Carpenter square # 1 Phillips screwdriver (optional) Tin snips (for cutting damper, if required) Scissors 3 1 5 Electric drill with ⁄16“, ⁄2“ and ⁄8“ (to cut template, if necessary) drill bits Filler blocks or scrap wood pieces, if needed for top cabinet spacing (used on recessed bottom cabinet installations only) Gloves Saw (saber, hole or keyhole) Stud finder or Hammer (optional) Duct and masking t
Résumé du contenu de la page N° 6
Installation Instructions PLACEMENT OF THE MOUNTING PLATE 1 A. REMOVING THE MICROWAVE B . FINDING THE WALL STUDS OVEN FROM THE CARTON/ REMOVING THE MOUNTING PLATE 1 Remove the installation instructions, filters, glass tray and the small hardware bag. Do not remove the Styrofoam protecting the front of the oven. Wall Studs Fold back all 4 carton flaps fully against carton 2 sides. Then carefully roll the oven and carton over onto the top side. The oven should be resting in the Styrofoam. Cente
Résumé du contenu de la page N° 7
At least 30 ″ (76.2 cm), up to 36 ″ (91.4 cm) Installation Instructions DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET C. Plate position—beneath framed recessed Plate position—beneath flat bottom cabinet bottom cabinet Mounting Plate Tabs Mounting Plate Tabs Touching the Cabinet Bottom Touching the Back Frame 30 ″ (76.2 cm) to Cooktop Plate position—beneath recessed bottom Your cabinets may have decorative trim that cabinet with front overhang interferes with the microwave installatio
Résumé du contenu de la page N° 8
Installation Instructions D. ALIGNING THE WALL PLATE Hole B Hole A Draw a Vertical Line on Wall from Center of Centerline Top Cabinet Notches Hole D CAUTION: Wear gloves Hole C to avoid cutting fingers on Area E sharp edges. NOTE: If neither C nor D is in a stud, find a stud 1 Draw a vertical line on the wall at the center of the somewhere in area E and draw a fifth circle to line up 30 ″ (76.2 cm) wide space. with the stud. It is important to use at least one wood 2 Use the mounting plate as t
Résumé du contenu de la page N° 9
Installation Instructions 2 INSTALLATION TYPES (Choose A, B or C) This microwave oven is designed for adaptation to NOTE: This microwave is shipped assembled for the following three types of ventilation: Recirculating. Select the type of ventilation required for your installation and proceed to that section. A. Outside Top Exhaust (Vertical Duct) B. Outside Back Exhaust (Horizontal Duct) C.Recirculating (Non-Vented Ductless) OUTSIDE TOP EXHAUST OUTSIDE BACK EXHAUST A B (VERTICAL DUCT) (HORIZONT
Résumé du contenu de la page N° 10
Installation Instructions HOOD EXHAUST NOTE: Read these next two pages only if you plan to vent your exhaust to the outside. If you plan to recirculate the air back into the room, proceed to page 6. OUTSIDE TOP EXHAUST (EXAMPLE ONLY) The following chart describes an example of one possible ductwork installation. EQUIVALENT NUMBER EQUIVALENT DUCT PIECES LENGTH x USED = LENGTH Roof Cap 24 Ft. (7.3 m) x (1) = 24 Ft. (7.3 m) 12 Ft. (3.6 m) Straight Duct 12 Ft. (3.6 m) x (1) = 12 Ft. (3.6 m) (6”/15.2
Résumé du contenu de la page N° 11
Installation Instructions NOTE: If you need to install ducts, note that the total Maximum duct length: 1 duct length of 3 ⁄4” x 10” (8.2 x 25.4 cm) rectangular or For satisfactory air movement, the total duct length of 6” (15.2 cm) diameter round duct should not exceed 1 3 ⁄4” x 10” (8.2 x 25.4 cm) rectangular or 6” (15.2 cm) 120 equivalent feet (36.5 m). diameter round duct should not exceed 120 equivalent Outside ventilation requires a HOOD EXHAUST DUCT. feet (36.5 m). Read the following ca
Résumé du contenu de la page N° 12
Installation Instructions OUTSIDE TOP EXHAUST (Vertical Duct) A INSTALLATION OVERVIEW A1. Attach Mounting Plate to Wall A2. Prepare Top Cabinet A3. Adapting Microwave Blower for Outside Top Exhaust A4. Check Damper Operation A5. Mount Microwave Oven A6. Adjust Exhaust Adaptor A7. Connect Ductwork IMPORTANT NOTES: • Make sure the screws for the blower motor and blower plate are securely tightened when they are reinstalled. This will help to prevent excessive vibration. • Make sure the motor
Résumé du contenu de la page N° 13
Installation Instructions A2. USE TOP CABINET TEMPLATE 2 Carefully pull out the blower unit. The wires will extend far enough to allow you to adjust FOR PREPARATION OF TOP the blower unit. CABINET End B You need to drill holes for the top support screws, a hole large enough for the power cord to fit through, and a cutout large enough for the exhaust adaptor. End A Back of Microwave Roll the blower unit 90° so that fan blade 3 openings are facing out the top of the microwave. Before Rotation Af
Résumé du contenu de la page N° 14
Installation Instructions A5. MOUNT THE MICROWAVE A3. ADAPTING MICROWAVE OVEN BLOWER FOR OUTSIDE TOP EXHAUST Secure blower unit to microwave with the screw 5 removed in Step 1. Make sure the screw is tight. Replace blower plate with the screw removed in 6 Step 1. Make sure the screw is tight. FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN. IMPORTANT: Do not grip or use handle Back of Microwave during installation. NOTE: If your cabinet is
Résumé du contenu de la page N° 15
Installation Instructions A5. MOUNT THE MICROWAVE A6. ADJUST THE EXHAUST OVEN (cont.) ADAPTOR Open the top cabinet and adjust the exhaust adaptor Cabinet Front to connect to the house duct. Cabinet Bottom Shelf Filler Block Back of Damper Blower Plate Microwave Equivalent to Depth of Cabinet Recess Self-Aligning Screw For Front-to-Back or Microwave Oven Top Side-to-Side Adjustment, Slide the Exhaust Adaptor 4 Attach the microwave oven to the top cabinet. as Needed Insert 2 self-aligning scre
Résumé du contenu de la page N° 16
Installation Instructions OUTSIDE BACK EXHAUST (Horizontal Duct) B INSTALLATION OVERVIEW B1. Prepare Rear Wall B2. Remove Blower Plate B3. Attach Mounting Plate to Wall B4. Prepare Top Cabinet B5. Adjust Blower B6. Mount the Microwave Oven IMPORTANT NOTES: • Make sure the screws for the blower motor and blower plate are securely tightened when they are reinstalled. This will help to prevent excessive vibration. • Make sure the motor wiring has been properly routed and secured, and that th
Résumé du contenu de la page N° 17
Installation Instructions ATTACH THE MOUNTING B4. B3. USE TOP CABINET TEMPLATE PLATE TO THE WALL FOR PREPARATION OF TOP CABINET You need to drill holes for the top support screws and a hole large enough for the power cord to fit through. Attach the plate to the wall using toggle bolts. At least one wood screw must be used to attach the plate to a wall stud. 1 Remove the toggle wings from the bolts. • Read the instructions on the TOP CABINET TEMPLATE. 2 Insert the bolts into the mounting plat
Résumé du contenu de la page N° 18
Installation Instructions 7 Place the blower unit back into the opening. ADAPTING MICROWAVE B5. AFTER: Fan Blade BLOWER FOR OUTSIDE Openings Facing Back BACK EXHAUST (cont.) End A Roll the blower unit 90° 3 Before Rotation After Rotation End B CAUTION: Do not pull or stretch the blower unit wiring. Make sure the wires are not Back of pinched, and that they are properly secured. Back of Microwave Microwave NOTE: The blower unit exhaust openings should match exhaust Rotate blower unit counterclo
Résumé du contenu de la page N° 19
Installation Instructions Cabinet Front B6. MOUNT THE MICROWAVE Cabinet Bottom Shelf OVEN Filler Block Equivalent to Depth of Cabinet Recess Self-Aligning Screw FOR EASIER INSTALLATION AND PERSONAL Microwave Oven Top SAFETY, WE RECOMMEND THAT TWO PEOPLE 4 Attach the microwave oven to the top cabinet. INSTALL THIS MICROWAVE OVEN. IMPORTANT: Do not grip or use handle 5 Insert 2 self-aligning screws during installation. through outer top cabinet NOTE: If your cabinet is metal, use the nylon hole
Résumé du contenu de la page N° 20
Installation Instructions RECIRCULATING (Non-Vented Ductless) C INSTALLATION OVERVIEW C1. Attach Mounting Plate to Wall C2. Prepare Top Cabinet C3. Check Blower Plate Mount the Microwave Oven C4. C5. Install or change Charcoal Filter IMPORTANT NOTES: • Make sure the screws for the blower motor and blower plate are securely tightened when they are reinstalled. This will help to prevent excessive vibration. • Make sure the motor wiring has been properly routed and secured, and that the wires are
